Makita XLC08ZB Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XLC08ZB manuals!
Problems with Makita XLC08ZB?
Ask a Question
Free Makita XLC08ZB manuals!
Problems with Makita XLC08ZB?
Ask a Question
Popular Makita XLC08ZB Manual Pages
Instruction Manual - Page 2
... ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. Do not use and before servicing.
2....instructions)
SPECIFICATIONS
Model:
XLC08
Capacity
730 mL
Continuous use the battery cartridges and chargers listed above may not be available depending on wet surfaces. Do not allow to our continuing program of any other battery cartridges and chargers may differ from appliance when not in this manual...
Instruction Manual - Page 3
...parts of body away from the appliance before use with the charger specified by a qualified repair person using only identical replacement parts. Read this instruction manual and the charger instruction manual...pack from openings and moving parts.
9. Have servicing performed by the manufacturer. ... accidentally occurs, flush with specifically designated battery packs.
This appliance...
Instruction Manual - Page 4
... symbols used for cracks or damage before operation.
5. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
2....with the battery cartridge. To reduce your eyesight.
5.
volts
direct current
Important safety instructions for battery cartridge
1. It may cause fire, injury and/ or property damage. ...
Instruction Manual - Page 5
...5 ENGLISH Installing the batteries to cause burns.
16. It may result in burns or personal injury.
17.
SAVE THESE INSTRUCTIONS. Do not..., and grooves of battery.
12. Unless the tool supports the use near a high-voltage electrical power lines....is severely damaged or is completely worn out. Overcharging shortens the battery service life.
3. A battery short can explode in a fire.
8....
Instruction Manual - Page 6
... brought to a temporary halt or stop automatically. Charge the battery(ies) or replace it into place. FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched...the figure, it may cause injury. ENGLISH Fig.1
Installing or removing battery cartridge
CAUTION: Always switch off your local Makita Service Center. Protections against other causes that causes it locks...
Instruction Manual - Page 7
...installing the battery cartridge into the tool, set the slide switch to "O" side and check that the switch trigger actuates properly and returns to "O" side: To start the tool, simply pull the switch trigger. The lamp goes out immediately after you stop the cleaner, set... depends on .
Slide switch 2. While the cleaner is set the slide switch to "O" side and release the switch trigger...
Instruction Manual - Page 9
...high performance filter. Clean out the fine dust and lightly tap to rectify problem. Handle 3. If the problem as described later occurs, high performance filter is not loaded correctly, dust ...9658; 1 . High performance filter Twist high performance filter in the direction of arrow to set a garbage bag beneath capsule. Attach the capsule. Securing lip
NOTE: When using cleaner.
Fig...
Instruction Manual - Page 10
...Groove of cleaner housing
Installing or removing stay / HEPA filter
Optional accessory
For the stay and sponge filter
To remove the stay, push up the bottom part of pillars of the ...on the cleaner. Insert the sponge filter between the pillars and set it to secure. To remove, follow the installation procedure in cleaner. Problem Example
The securing lip of high performance filter is too much ...
Instruction Manual - Page 11
... the air vent when operating the cleaner. The nozzle slips on the wall etc. Hook 4.
Suction inlet 2. Nozzle
1
Fig.22
2
► 1 .
Release button
NOTICE: When installing the attachment with the hook on the attachment. OPERATION
CAUTION: Do not move your hand on easily.
Instruction Manual - Page 13
...in the clogged condition may cause poor suction and shorten the service life of the cleaner using Makita replacement parts. Fig.34 13 ENGLISH Clean out also the suction opening and...the filter from time to re-install them thoroughly before use the cleaner without any other support may result.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment...
Instruction Manual - Page 14
...clogged? Is the nozzle/pipe inlet blocked? Insert the sponge filter between the pillars and set it in the nozzle, pipe or suction inlet of dust?
Is the battery cartridge ... beam or column, where the wall mount for repairs, check the following points. Is the battery cartridge discharged?
Bottom edge of pillar
Troubleshooting
Before asking for cordless cleaner can be investigated Is...
Instruction Manual - Page 15
...These accessories or attachments are recommended for use with your local Makita Service Center. • Extension wand (Straight pipe) • Nozzle...
3
Fig.37 ► 1 . The use the cleaner in this manual. They may result in a motor malfunction.
15 ENGLISH Hook 3. Extension ...cyclone attachment
Using the cleaner with the filters installed, even when using the cyclone attachment. ...
Instruction Manual - Page 16
... washing the cyclone attachment, dry it thoroughly before use the cyclone attachment without lock function.
NOTE: To install or remove the cyclone attachment, refer to the surface of dust" for the removal procedure.)
Dry the parts thoroughly before reinstallation and use.
2
3
1 2
Fig.38 ► 1 .
Button (two locations)
4. Insert the dust case all...
Instruction Manual - Page 17
... WARRANTY
Please refer to the annexed warranty sheet for the most current warranty terms applicable to the warranty details set forth at below website for your respective country. If annexed warranty sheet is installed securely.
2 3
1
Fig.42 ► 1 . Remove the dust on the mesh filter and then wash it with the port...
Parts Breakdown - Page 2
Model XLC08ZB Price List
Item#
Part#
Description
Q'ty
001
183Y64-0 HOUSING SET
1
001 C10 263005-3
RUBBER PIN 6
2
001 C20 422974-9
...SEAL
1
017
629B87-1 MOTOR ASSEMBLY
1
018
413645-9
MOTOR COVER F
1
019
266429-2
TAPPING SCREW 3X16
4
020
183Y64-0 HOUSING SET
1
020 C10 263005-3
RUBBER PIN 6
2
020 C20 422974-9
SPONGE SHEET
2
020 C30 8059A7-0 CAUTION LABEL
1
020 D10...
Makita XLC08ZB Reviews
We have not received any reviews for Makita yet.