Makita XRH03Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XRH03Z manuals!
Problems with Makita XRH03Z?
Ask a Question
Free Makita XRH03Z manuals!
Problems with Makita XRH03Z?
Ask a Question
Popular Makita XRH03Z Manual Pages
XRH03Z Instruction Manual - Page 2
...risk of electric shock. 5.
When operating a power tool outdoors, use . ENGLISH (Original instructions)
SPECIFICATIONS
Model
XRH03
Concrete
24 mm (7/8")
Capacities
Steel
13 mm (1/2")
Wood
26 mm (1-1/16")
No load speed... specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts....
XRH03Z Instruction Manual - Page 3
... with specifically designated...instructions, taking into account the working conditions and the work to control. 23. Properly maintained cutting tools with the charger specified by insulated gripping surfaces, when performing an operation where the cutting accessory may affect the power tool's operation. avoid contact. Service...qualified repair person using only identical replacement parts....
XRH03Z Instruction Manual - Page 4
...in every six months if you do not use ) replace strict adherence to safety rules for tool. ･ ...instruction manual may reach or exceed 50 ﾟ C (122 ﾟ F). 7. Operate the tool
only when hand-held. 12. Do not touch the bit or parts... lubrication. Always stop operating immediately. Overcharging shortens the battery service life. 3. Without proper warm-up, hammering operation is ...
XRH03Z Instruction Manual - Page 5
... a Makita service center. If the tool does not start the tool, simply pull the switch trigger. Switch action
1. FUNCTIONAL DESCRIPTION
CAUTION: • Always be seen. Installing or removing battery cartridge
1. Button
1
3. Install it fully until it locks in the housing and slip it to become overloaded. In this situation, remove and recharge the battery...
XRH03Z Instruction Manual - Page 6
... knob to the neutral position. Changing the direction of rotation before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to the
symbol. This will be sure that the action mode changing knob is released. When this tool. Reversing switch action...
XRH03Z Instruction Manual - Page 7
... beforehand with a small amount of times. Bit shank
1
2. Then insert the bit again. After installing, always make sure that the teeth on the grip fit in , remove the bit. To change ...it engages.
1. Bit 2. Loosen 6. This chuck lubrication assures smooth action and longer service life.
Installing or removing the bit Clean the bit shank and apply bit grease before carrying out any...
XRH03Z Instruction Manual - Page 8
...bounce around, uncontrolled. Adjust the depth gauge to the symbol.
Dust cup
1. Dust cup
1
Set the action mode changing knob to the desired depth and tighten the side grip. Instead, run ... (auxiliary handle) and firmly hold the tool by both hands.
Chipping/Scaling/Demolition
008833
008837
Set the action mode changing knob to prevent dust from falling over the tool and on the tool...
XRH03Z Instruction Manual - Page 9
...8226; A stuck bit can be damaged. Recesed part 2. Discoloration, deformation or cracks may back out... bit, decrease the tool performance and shorten the service life of hole breakthrough. Drilling in the holders....replaced at the time of the tool. • There is installed on the tool. Replace when they wear down device.
001145
Remove and check the carbon brushes regularly. Set...
XRH03Z Instruction Manual - Page 10
... gives you specific legal rights, and you need any other maintenance or adjustment should be performed by defective workmanship or material, Makita will repair (or at our option, replace) without charge. MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. THIS DISCLAIMER...
XRH03Z Parts Breakdown - Page 2
Model XRH03Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
Q'ty Unit
001
286263-4
002
233940-9
003
417629-9
004
257241...-2
047
961003-8
048
233343-7
049
227179-4
050
324668-1
CAP 35 RING SPRING 19 CHUCK COVER RING 21 GUIDE WASHER CONICAL COMP. WASHER GRIP BASE GRIP 36 COMPLETE HEX. NUT M8 CHANGE LEVER COMPRESSION SPRING 3 LOCK BUTTON...
XRH03Z Parts Breakdown - Page 3
... BEARING 627DDW
073
267816-8 WAVE WASHER 15
074
815F25-5 XRH03 NAME PLATE
075
187817-9 HOUSING SET
075 C10 802W15-9 CAUTION LABEL
075 D10
INC. 82
... PC. 1 PC. 1 PC. 1 PC. 0 1 PC. 1 PC. 1 PC. 1 1 1 0 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 1 0 2 PC. 2 PC. 1 SET 1 PC. 1 PC. 1 PC. 1 PC. 7 PC. 1 PC. 1 PC. 2 PC. 0 1 PC. 1 PC. 1 PC. 2 PC. 0 2 PC. 1 PC. 1 PC. 051
331992-5 CLUTCH CAM
052
219014-0...
Makita XRH03Z Reviews
We have not received any reviews for Makita yet.