Makita XRT02ZK Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XRT02ZK manuals!
Problems with Makita XRT02ZK?
Ask a Question
Free Makita XRT02ZK manuals!
Problems with Makita XRT02ZK?
Ask a Question
Popular Makita XRT02ZK Manual Pages
Instruction Manual - Page 2
...installed in the arm.
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications...on your region of residence. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XRT02
Tie wire (Optional accessory) Annealing ...guide B complete (EG) is not designed for high tying strength.
-
-
-
2 ...
Instruction Manual - Page 3
... liquids, gases or dust. Keep cord away from heat, oil, sharp edges or moving parts. Use of a cord suitable for outdoor use the cord for carrying, pulling or unplugging ... create sparks which may ignite the dust or fumes. 3. Save all safety warnings, instructions, illustrations and specifications provided with earthed (grounded) power tools. Power tool plugs must match the outlet. ...
Instruction Manual - Page 4
... when using only identical replacement parts. When battery pack is an employer's responsibility to a rotating part of injury.
6. Never service damaged battery packs. Use personal protective equipment. Prevent unintentional starting the power tool accidentally.
4. Store idle power tools out of the reach of the tool in personal injury.
5. Follow instruction for which may result...
Instruction Manual - Page 5
... place your finger on the trigger. When installing the battery cartridge, be sure to the tool.... Otherwise, your wrist may be twisted or your local Makita Service Center for repairs. Otherwise, your hand may be caught by yourself. When working... you may get caught in the rotating part and cause an accident.
6. Be careful not to the error display. (Ask your footing and cause ...
Instruction Manual - Page 6
... of electrolyte.
13. Unless the tool supports the use near high-voltage electrical power lines. SAVE THESE INSTRUCTIONS. Tips for battery cartridge
1. Always stop...been altered, may reach or exceed 50 °C (122 °F).
7. Installing the batteries to water or rain. Do not allow chips, dust, or ... the battery service life.
3. When not using battery.
2. Charge the battery cartridge if you...
Instruction Manual - Page 9
...10 ► 1 . When you may be injured.
Tying strength setting
CAUTION: Be sure to lock the trigger before carrying out any work on the tool. The error tone will continue to sound until the power is shown on the .... Display panel
If the wire is extremely low, the error tone may cause the tool to the binding or rotating parts of the tool tip.
After tying, check the twisted ...
Instruction Manual - Page 14
...-related problem, do not intend to use it, an accident may be pulled. If you may occur. Ask your local Makita Service Center for repairs. Checking the curl guide
To prevent the operator from touching the binding or rotating parts of the tool is abnormal. Checkout for repairs. If the tool operates and if no error is...
Instruction Manual - Page 15
...Otherwise, you may
be sure to release your limbs or face close to the binding or
4
rotating parts of the
1
tool tip. NOTICE: Make sure that the battery cartridge is removed and the trigger ...the battery cartridge into the tool, and turn the power on , never touch the binding or rotating parts of the tool tip. Tying mode lamp
Single actuation mode
1. CAUTION: When the power is turned on...
Instruction Manual - Page 16
... wire has clung to hook the arm on the rebars, and then pull the tool up. The wire will be careful not to the binding part of the tool tip, turn the power of the tool off. After tying, be tied. Fig.38 ► 1 . Fig.37
45° 45°
Fig...
Instruction Manual - Page 17
...Fig.41
17 ENGLISH Fig.42 • If tying strength is completed.
• The tool tip rotating part (hook) twists the wire during the wire tying process, the wire will be repelled a second time. ...is displayed. Fig.40
Cautions on the hook, which may cause an accident. 1. 4.
Replace with no tie wire left, an error is not pulled by the tool.
• Do not touch the wires during the ...
Instruction Manual - Page 18
..., follow the steps below.
1. Insert the battery cartridge into the guide little by Makita Authorized or Factory Service Centers, always using tools such as nippers or pliers.
1
Fig.45 ► 1 .
Remove the wire breaks using Makita replacement parts.
2
Fig.46 ► 1 . In this state, replace the wire reel with the lock lever.
1
MAINTENANCE
CAUTION: Always...
Instruction Manual - Page 19
.... Wire brush 5. Close the reel cover.
1 Fig.50 ► 1 . Guide
Cleaning with disassembly
If the cutter section is clogged or a wire is enough with ... caught in the tool package.
1
Fig.52 ► 1 .
Gear 2. Guide 3. Reel cover
Fig.51 ► 1 . Air duster gun 2. Then bring the air duster gun close
to the guide and blow the air. Arm 2. 1
Using the air duster gun
2
Open...
Instruction Manual - Page 20
... A 3. Bolt B 3. Bolt B will be removed using the hex wrench.
2. Cutter B 3. Install cutter A and link arm A to the following procedure.
1. 4. Bolt B 3. Wire guide B
20 ENGLISH Remove bolt A, and remove wire guide B.
1
5 Fig.57
► 1 . Arm plate A
Assembling
When cleaning is finished, assemble the parts according to fit the shape of the arrow and remove it...
Instruction Manual - Page 22
...Service Centers for repairs.
Close the curl guide.
CAUTION: When you may be injured.
Error tone and display
If an error occurs, an error tone will sound, and an error number will be sure to the binding or rotating parts...tip. Cool the battery cartridge down . Replace the battery cartridge with a recharged one. CAUTION: If an error tone sounds, or if the tool malfunctions...
Instruction Manual - Page 23
...regarding these accessories, ask your local Makita Service Center. • Tie wire • Wire guide B complete (EG) • Wire... brush • Extension handle • Makita genuine battery and charger NOTE: Some items in the list may differ from country to the warranty details set...to this manual. OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are...
Makita XRT02ZK Reviews
We have not received any reviews for Makita yet.