Makita XT262R Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XT262R manuals!
Problems with Makita XT262R?
Ask a Question
Free Makita XT262R manuals!
Problems with Makita XT262R?
Ask a Question
Popular Makita XT262R Manual Pages
Instruction Manual - Page 2
...Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Do not use any way. A wrench or a key left attached to a rotating part...ignite the dust or fumes. 3. Prevent unintentional starting. Do not overreach. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XSF03
Capacities
Self drilling screw Drywall screw
6 mm (1/4") 5 mm (3/16")
No load speed ...
Instruction Manual - Page 3
... a qualified
repair person using the tool in moving parts.
16. ...replacement parts. Hold the tool firmly. 4. Do not use . in the hands of any adjustments, changing accessories, or storing power tools.
Service 28. Dress properly. Do not wear loose clothing or jewellery. SAVE THESE INSTRUCTIONS...from those intended could result in this instruction manual may cause burns or a fire....
Instruction Manual - Page 4
...; direct current
・ no load speed
・ revolutions or reciprocation per minute
IMPORTANT SAFETY INSTRUCTIONS
ENC007-8
FOR BATTERY CARTRIDGE
1. Never recharge a fully charged battery cartridge. Let a hot battery...your local regulations relating to disposal of battery. Overcharging shortens the battery service life.
3. USD301-5
Symbols
The followings show the symbols used for ...
Instruction Manual - Page 5
... the trigger. Switch action
CAUTION: • Before inserting the battery cartridge into place.
Installing or removing battery cartridge
1. Button
1
3. Insert it all the way until the
red... the driver bit will start the tool, simply pull the switch trigger. To install the battery cartridge, align the tongue on , tool is shutdown. CAUTION: • Always install the...
Instruction Manual - Page 6
Button
015163
To turn on . The lamp goes out approximately 10 seconds after switch trigger release, have tool serviced at a Makita service center. To turn on to draw an abnormally high current, the tool automatically stops without any indications. In push drive mode with the switch trigger ...
Instruction Manual - Page 7
...
7
Locator
B
015165
The depth can be pulled.
CAUTION: When not operating the tool, always set the reversing switch lever to change in the neutral position, the switch trigger cannot be adjusted by...; Never hook the tool at high location or on again. Depth adjustment
B
1 A
A
1. Installing or removing the bit
1. Drive a trial screw into your material or a piece of the locator ...
Instruction Manual - Page 8
...out of the workpiece to push in this manual. OPTIONAL ACCESSORIES
CAUTION: • These accessories ... install the bit, push it out. Then install the locator by Makita Authorized or Factory Service Centers, always using Makita replacement parts. To install ...To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should ...
Instruction Manual - Page 9
... OF THE PRODUCT. This Warranty does not apply where:
repairs have been made to the tool. This Warranty gives you specific legal rights, and you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. Some states do not allow limitation on...
XSF03Z Parts Breakdown - Page 2
...1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 1 SET 2 PC. 0 1 7 PC. 3 PC. 1 1 1 PC. 1 PC. 1 SET 2 PC. 0 1 1 PC. 1 PC. 2 PC. 1 3 PC. Model XSF03Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
Q'ty Unit
001
455591-0 LOCK RING
002
424235-3 SEAL RING 30
... COMPLETE
029
233619-2 TORSION SPRING 3
030
187968-8 HOUSING SET
030 C10 263005-3 RUBBER PIN 6
030 D10
INC. 38...
Makita DC18RC Instruction Manual - Page 3
...damaged, ask Makita authorized
service center to replace it will not be.... IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
1. This manual contains important safety and operating instructions for use or... it stops adjusting to the guide of time. 6. aged in...light will begin with pulling out the battery cartridge. 3. ENGLISH
Specifications
Model Input Output Weight
DC18RA
DC18RC
A.C. 120 V 50 - 60 ...
Makita DC18RC Instruction Manual - Page 4
...flash for cooling. • The products should be sent to repair or maintenance, if the yellow warning light will begin after the...no sound of cooling air comes out during cooling, which means no trouble on the charger, which is for heated battery in the charger cools ...is too hot, charging will begin after the cooling fan installed in order to enable the battery to direct sunlight for...
Makita XT262R Reviews
Do you have an experience with the Makita XT262R that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!