Makita XTR01T7 Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XTR01T7 manuals!
Problems with Makita XTR01T7?
Ask a Question
Free Makita XTR01T7 manuals!
Problems with Makita XTR01T7?
Ask a Question
Popular Makita XTR01T7 Manual Pages
XTR01 Instruction Manual - Page 2
... is unavoidable, use the cord for future reference. Remove any way. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Collet chuck capacity No load speed Overall length Rated voltage Standard battery cartridge
XTR01 1/4"...the table. The term "power tool" in the warnings refers to a rotating part of a cord suitable for appropriate conditions will reduce personal injuries.
3. Do not...
XTR01 Instruction Manual - Page 3
... situations.
6. Use power tools only with another practical way to secure and support the workpiece to control.
7. Do not use of parts and any other condition that the safety of operation.
4. Never service damaged battery packs. Hold power tool by a qualified repair person using the tool, do not allow for operations different from moving...
XTR01 Instruction Manual - Page 4
... replace ... the battery service life.
3....installed bit.
11. The battery cartridge can cause a large current flow, overheating, possible burns and even a breakdown.
6. Do not use genuine Makita batteries.
CAUTION: Only use a damaged battery.
10. Charge the battery cartridge with . 10. it for a while.
Be careful not to follow the safety rules stated in this instruction manual...
XTR01 Instruction Manual - Page 10
..., then insert the tool into the offset base.
1
► 1 . Collet cone
3. Install the pulley on the base plate, and then remove the base plate.
10 ENGLISH Remove the collet...lock and tightening the pulley with the wrench.
► 1 . Shaft lock 4. Installing or removing the offset base
Optional accessory 1. Belt 7. Close the lock lever.
► 1 . Loosen the screws...
XTR01 Instruction Manual - Page 12
... it on the dust nozzle. Guide bar
Installing or removing the dust nozzle on the workpiece without the trimmer bit making any contact. Move the tool forward over the workpiece surface. Thumb screw
NOTE: Before cutting on the actual workpiece, it flush with the trimmer base
Set the tool base on the plunge...
XTR01 Instruction Manual - Page 13
... the trimmer base. In this case, firmly clamp a straight board to the trimmer base with progressively deeper bit settings. 3. Using the straight guide
Optional accessory 1. Wing nut
4. Loosen the wing nut on the straight guide and adjust the distance between the side of the workpiece and the cutting position is not straight, the...
XTR01 Instruction Manual - Page 14
...be cut. Pivot the tool around the nail in diameter into the center hole to secure the straight guide. Center hole
NOTE: Circles between 70 mm (2-3/4") and 121 mm (4-3/4") in radius.
1
1
2...► 1 . Loosen the screws on the base, and then attach the base plate by using this guide. For cutting circles between the center of circle
1
and the center of the circle to be cut (...
XTR01 Instruction Manual - Page 15
... distance (X) can be calculated by turning the adjusting screw (1 mm (3/64") per turn). Workpiece 2. Loosen the clamp screw, then install the trimmer guide on the workpiece is the distance (X) between the trimmer bit and the trimmer guide by using the following equation:
Distance (X) = (outside of the workpiece.
1
2
3 ► 1 . Move the tool with the...
XTR01 Instruction Manual - Page 16
...
► 1 .
Trimmer base plate
2. Loosen the screws on the offset base instead of the bar type grip.
1
2
► 1 . Install the straight guide to the guide holder by tightening the screws. 3. Bar type grip 2. Insert the guide holder into the holes in the plunge base, and then tighten the wing bolts.
► 1 . Offset base plate...
XTR01 Instruction Manual - Page 17
... board to secure the parallel ruler. Feed the tool in the same way as the straight guide for straight cuts when chamfering or grooving. Loosen the wing nut on the base and remove ...the parallel ruler cannot be used for the trimmer base. Using the templet guide
Optional accessory
1. Screw 2. Place the templet guide on the base, and then tighten the screws. At the desired distance,...
XTR01 Instruction Manual - Page 18
... remove the knob type grip, and then install the bar type grip by Makita Authorized or Factory Service Centers, always using Makita replacement parts. The use with your local Makita Service Center. • Straight and groove forming bits • Edge forming bits • Laminate trimming bits • Straight guide assembly • Trimmer guide assembly • Trimmer base assembly •...
XTR01 Instruction Manual - Page 19
...specific legal rights, and you .
19 ENGLISH Should any trouble...replace) without charge. If inspection shows the trouble is caused by others: • repairs are required because of normal wear and tear: • the tool has been abused, misused or improperly
maintained: • alterations have other rights which vary from the date of Makita's Factory or Authorized Service Centers. MAKITA...
XTR01 Parts Breakdown - Page 2
Model XTR01 Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
853N12-4... GEAR 16 FLAT WASHER 5 HEX. LOCK NUT M5-8 BASE PROTECTOR COUNTERSUNK HEAD SCREW M4X10 CAM PLATE LOCK LEVER COMPLETE RUBBER CAP TRIMMER BASE SET INC. 24-37 STRAIGHT GUIDE ASSEMBLY THUMB NUT M6 CAP SQUARE NECK BOLT M6X20
1 1 PC. 4 PC. 1 1 2 PC. 1 0 1 1 1 1 2 PC. 1 0 1 1 PC. 1 ...
XTR01 Parts Breakdown - Page 3
... XTR01T7 INDICATION LABEL XTR01T7 PLASTIC CASE LABEL TRAY PLUNGE BASE SET COMBO-PARTS TEMPLET GUIDE 16 BATTERY COVER DC18RC FAST CHARGER BATTERY BL1850B SET (197283-2)
E01
813J80-5 CAUTION LABEL
1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC.
1 PC. (XTR01T7) 4 PC. (XTR01T7) 1 (XTR01T7) 2 (XTR01T7) 1 PC. (XTR01T7) 1 PC. (XTR01T7) 0 (XTR01T7) 1 PC. (XTR01T7) 2 PC. (XTR01T7) 1 PC. (XTR01T7) 2 (XTR01T7...
Makita XTR01T7 New Tool Flyer English - Page 1
...• Makita-built brushless motor delivers faster and more precise settings
DURABILITY
Aluminum housing and base for convenient depth
adjustments and base removal/installation
SPECIFICATIONS
Collet 1/4" No Load Speed (variable speed)...... 10,000 - 30,000 RPM Brushless Motor Yes Battery 18V LXT® Lithium-Ion Overall Length 5-1/4" Net Weight (with battery 4.6 lbs. UPC Code (XTR01T7...
Makita XTR01T7 Reviews
Do you have an experience with the Makita XTR01T7 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!