Makita XVJ04Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XVJ04Z manuals!
Problems with Makita XVJ04Z?
Ask a Question
Free Makita XVJ04Z manuals!
Problems with Makita XVJ04Z?
Ask a Question
Popular Makita XVJ04Z Manual Pages
Instruction Manual - Page 2
...are subject to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Do not use an extension cord suitable for ... the risk of the battery cartridges and chargers listed above . ENGLISH (Original instructions)
SPECIFICATIONS
Model: Length of residence. The lightest and heaviest combinations, according to rain or wet...
Instruction Manual - Page 3
...pack may result in accordance with specifically designated battery packs. Do not ...repair person using only identical replacement parts. in personal injury. The entanglement of parts and any other persons in the immediate working conditions and the work gloves in the USA. Use power tools only with these instructions.... Keep your power tool serviced by poorly maintained power tools...
Instruction Manual - Page 4
...Service of your eyes, rinse them before cutting so that it unstable and may result in a risk of the power tool "live " wire may contact hidden wiring. Use clamps or another practical way to secure and support...this instruction manual may reach or exceed 50 °C (122 °F).
7. Follow instruction for... (gained from moving parts.
10. It may... attempt to repair the appliance...
Instruction Manual - Page 5
...fall out of battery.
12. Unless the tool supports the use near high-voltage electrical power lines.... Use of the battery cartridge. Overcharging shortens the battery service life.
3. Failure to hold the tool and the ...install the battery cartridge forcibly. Installing the batteries to the handling of electrolyte.
13. Do not allow chips, dust, or soil stuck into place. SAVE THESE INSTRUCTIONS...
Instruction Manual - Page 6
... ENGLISH If no improvement can be found by restoring protection system, then contact your local Makita Service Center.
Selecting the cutting action
1
Fig.3 ► 1 .
Overdischarge protection
When the battery...the tool on the battery cartridge to restart. 2. Charge the battery(ies) or replace it on , the motor runs again but stops soon.
Indicating the remaining battery capacity...
Instruction Manual - Page 7
To change the cutting action, just turn the cutting action changing lever to be cut workpieces faster but the service life of the jig saw blade will allow you to select the appropriate cutting action. Medium orbital cutting action
For cutting wood and plywood.
For ...
Instruction Manual - Page 8
...2
3
Fig.7
► 1 . If the tool consistently fails to turn it back.
Before installing the jig saw blade with an electric brake. Blade clamp lever (fixed position)
8 ENGLISH
Disabling ... Pull the jig saw blade lightly to "5" by turning it, and then set at a Makita service center. Constant speed control
Electronic speed control for easy operation.
Electric brake
This ...
Instruction Manual - Page 9
... use, store the hex wrench as it will go. Jig saw blade breakage.
1
1
3
Fig.9 ► 1 . Jig saw blade
NOTE: In case that it is not installed completely. Do not press the blade clamp lever by hand to be released.
2
OPERATION
CAUTION: Always hold the base flush with the workpiece. Blade clamp...
Instruction Manual - Page 11
... a suitable coolant (cutting oil) when cutting metal. Apply pressure to do as shown in the figure.
1
Fig.19 ► 1 . Finishing edges
Installing or removing the dust cover
Optional accessory Install the dust cover as follows.
1. Dust extraction
Fig.17
You need not bore a starting hole or make dimensional adjustments, run the jig...
Instruction Manual - Page 12
... Fig.21 ► 1 .
Dust cover
Installing or removing the dust nozzle
Country specific You can connect this tool to the dust nozzle. Rip fence (Guide rule)
12 ENGLISH To remove the dust cover,...Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing accessories. Straight cuts
When repeatedly cutting widths of 160 mm (6-5/16") or...
Instruction Manual - Page 13
..., move the base all the way forward and fit it .
1
3
2
4
3. Rip fence (Guide rule)
1. Screw the threaded knob onto the circular guide pin to secure it on the fence guide. Hex wrench
13 ENGLISH NOTE: Always use the cover plate, install the anti-splintering device onto the cover plate.
Bolt 3. When you use jig...
Instruction Manual - Page 14
...local Makita Service Center. • Jig saw blades • Rip fence (guide rule) set • Guide rail adapter set •...repairs, any other maintenance or adjustment should be sure that the tool is switched off and the battery cartridge is not available, refer to this manual...set forth at below website for its stated purpose. B-8, B-13, B-16, B-17 or 58 when using Makita replacement parts...
Makita XVJ04Z Reviews
We have not received any reviews for Makita yet.