Makita XWT07T Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XWT07T manuals!
Problems with Makita XWT07T?
Ask a Question
Free Makita XWT07T manuals!
Problems with Makita XWT07T?
Ask a Question
Popular Makita XWT07T Manual Pages
Makita DC18RC Instruction Manual - Page 3
...it stops adjusting to the guide of batteries may not start. 16.
tery, and (3) product using battery charger, read all instructions and cautionary markings on ,...service center to replace it within another five seconds after this action makes the melody sound change. 3.
Other types of charger. Do not expose charger to cover or clog the charger vents. ENGLISH
Specifications
Model...
Makita DC18RC Instruction Manual - Page 4
...charging will begin after the cooling fan installed in this case. Charging will begin after...red light going out and the melody sound preset at which means no trouble on charger and battery for warning in spite of battery with dust.
... be sent to cold air. The battery employed in a location exposed to repair or maintenance, if the yellow warning light will flash for cooling. •...
XWT07/XWT08/XWT09 Instruction Manual - Page 1
IMPORTANTE: Lea antes de usar. INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Impact Wrench Boulonneuse sans Fil Llave de Impacto Inalámbrica
XWT07 XWT08 XWT09
IMPORTANT: Read Before Using. IMPORTANT : Lire avant usage.
XWT07/XWT08/XWT09 Instruction Manual - Page 2
...Water entering a power tool will reduce risk of electric shock.
4. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening capacities
Standard bolt
High tensile bolt
XWT07
XWT08
M12 - Drive shank
-...the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts.
...
XWT07/XWT08/XWT09 Instruction Manual - Page 3
...only identical replacement parts. Keep your...of control can be controlled with specifically designated battery packs. Do not ...medication. If damaged, have the power tool repaired before installation.
4. in personal injury.
5. Battery tool...with your power tool serviced by insulated gripping surfaces...instructions, taking into account the working conditions and the work to a rotating part...
XWT07/XWT08/XWT09 Instruction Manual - Page 4
...replace strict adherence to drop or strike battery. 9. Do not short the battery cartridge: (1) Do not touch the terminals with room temperature at 10 °C - 40 °C (50 °F - 104 °F).
Charge the battery cartridge before installing... instruction manual may cause them out with product (gained from rotating parts.... Overcharging shortens the battery service life.
3. It may...
XWT07/XWT08/XWT09 Instruction Manual - Page 5
...abnormally high current.
Then turn the tool off power to the tool to restart. To install the battery cartridge, align the tongue on the battery cartridge with a little click. Star .... CAUTION: Do not install the battery cartridge forcibly. Indicator lamps 2. The battery may differ slightly from the tool while sliding the button on the upper side of the model number
3
►...
XWT07/XWT08/XWT09 Instruction Manual - Page 6
... trigger. Be careful not to turn off , release it may lower the illumination. Reversing switch lever
6 ENGLISH Tool speed is released, have the tool serviced at a Makita service center. With the lamp status ON, pull the switch trigger to scratch the lens of light directly.
► 1 . NOTE: Use a dry cloth to the...
XWT07/XWT08/XWT09 Instruction Manual - Page 7
.... Changing the impact force
This tool has a reversing switch to a complete stop.
Specifications of blows changes in three steps: hard, medium and soft mode. CAUTION: Use ...
2,000 min-1 (/min)
Tightening when you need good controlled power.
CAUTION: When not operating the tool, always set the reversing switch lever to the work. Button
You can be pulled.
1
2 5
3
4
► ...
XWT07/XWT08/XWT09 Instruction Manual - Page 8
... High tensile bolt
M20 - M20 M10 -
Pin
Move the O-ring out of the impact socket with O-ring and pin
Only for Model XWT07
1
3
2
► 1 . To remove the impact socket, follow the installation procedures in the impact socket and square drive. M16 (1/2″ - 3/4″) (9/16″ - 3/4″) (3/8″ - 5/8″)
Soft
M12 - M16 M12...
XWT07/XWT08/XWT09 Instruction Manual - Page 9
...instructions above. Sleeve
To install the drill bit, pull the sleeve in the direction of the tool. In this case, try re-inserting the drill bit according to the air with hoist. Groove 2. This can see the red part...will not return to secure the drill bit. Installing or removing drill bit/ socket adapter
Only for Model XWT09 (optional accessory)
Ring
Only for Model XWT09
2 1
A 3
A=11.2 mm...
XWT07/XWT08/XWT09 Instruction Manual - Page 10
Model XWT07 Proper fastening torque for high tensile bolt
2
N•m (ft•lbs)
800 (590)
600 (440)
400 (300)
M24(1″) M24(1″)
M22(7/8″) M22(7/8&#...
XWT07/XWT08/XWT09 Instruction Manual - Page 11
...)
M24(1″) M24(1″)
200 (150)
M20(3/4″) M20(3/4″)
00
1
2
3
1
1. Model XWT08 Proper fastening torque for standard bolt
2
N•m (ft•lbs)
800 (590)
M30(1-1/4″)
...M30(1-1/4″)
600 (440)
400 (300)
200 (150)
M24(1″) M24(1″)
Model XWT09 Proper fastening torque for high tensile bolt
2
N•m (ft•lbs)
800 (590)...
XWT07/XWT08/XWT09 Instruction Manual - Page 12
...attempted by Makita Authorized or Factory Service Centers, always using Makita replacement parts. When the battery cartridge is discharged...impact socket
will be performed by others: • repairs are recommended for a longer period of bolts are...trouble develop during this manual. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. This Warranty gives you specific...
XWT07Z Parts Breakdown - Page 2
Model XWT07Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
251476-6
004
851K73-0
005
266326-2
006
183C08-8
006 D10...-2
H.S.H.BOLT M5X35 WITH WR XWT07 NAME PLATE TAPPING SCREW 4X18 HOUSING SET INC. 43 LED CIRCUIT F/R CHANGE LEVER SWITCH COMPLETE SWITCH PLATE COMPLETE BATTERY HOUSING SET RUBBER PIN 6 INC. 46 PIN 1.5 RUBBER PIN 5 CUSHION RUBBER...
Makita XWT07T Reviews
We have not received any reviews for Makita yet.