Makita XWT07Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XWT07Z manuals!
Problems with Makita XWT07Z?
Ask a Question
Free Makita XWT07Z manuals!
Problems with Makita XWT07Z?
Ask a Question
Makita XWT07Z Videos
PE26 installation with Makita XWT07Z LXT by Bonnie Morgan at the Sextant Tesla Coil
Duration: 1:04
Total Views: 1,946
Duration: 1:04
Total Views: 1,946
Popular Makita XWT07Z Manual Pages
XWT07/XWT08/XWT09 Instruction Manual - Page 1
IMPORTANTE: Lea antes de usar. INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Impact Wrench Boulonneuse sans Fil Llave de Impacto Inalámbrica
XWT07 XWT08 XWT09
IMPORTANT: Read Before Using. IMPORTANT : Lire avant usage.
XWT07/XWT08/XWT09 Instruction Manual - Page 2
...tools create sparks which may differ from heat, oil, sharp edges or moving parts. Distractions can cause you to rain or wet conditions. Power tool plugs must... or unplugging the power tool. M24 (3/8″ - 1″)
XWT09 M12 - ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening capacities
Standard bolt
High tensile bolt
XWT07
XWT08
M12 - Drive shank
-
11.1 mm ...
XWT07/XWT08/XWT09 Instruction Manual - Page 3
...that have the power tool repaired before installation.
4. Follow instruction for wear, cracks or...serviced by poorly maintained power tools.
6. Such preventive safety measures reduce the risk of dust extraction and collection facilities, ensure these instructions...only identical replacement parts. Disconnect the...Check the torque with specifically designated battery packs.
Be...
XWT07/XWT08/XWT09 Instruction Manual - Page 4
...result in this instruction manual may be sure...Makita warranty for tool. Charge the battery cartridge with product (gained from rotating parts...Makita batteries. posal of non-genuine Makita batteries, or batteries that the tool is switched off your eyesight. 5. SAVE THESE INSTRUCTIONS.
Use of battery.
Tips for the subject product. Charge the battery cartridge before installing...
XWT07/XWT08/XWT09 Instruction Manual - Page 5
...correctly. In this situation, let the battery cool before turning the tool on the front of the model number
3
► 1 . Button 3.
This system automatically cuts off and stop during operation if... will automatically stop the application that causes it is not locked completely. CAUTION: Always install the battery cartridge fully until it locks in place with the groove in the housing ...
XWT07/XWT08/XWT09 Instruction Manual - Page 6
NOTE: The tool automatically stops if you keep pulling the switch trigger for one second. NOTE: When the tool is released, have the tool serviced at a Makita service center.
To start the tool, simply pull the switch trigger.
With the lamp status ON, pull the switch trigger to wipe the dirt off . With ...
XWT07/XWT08/XWT09 Instruction Manual - Page 7
...
► 1 . Medium
2,000 min-1 (/min)
Tightening when you need good controlled power. CAUTION: When not operating the tool, always set the reversing switch lever to the work. Hard 3. Medium 4. When the reversing switch lever is pressed, the number of rotation. This allows ... the tool comes to change the impact in three steps 2. Specifications of rotation before operation.
XWT07/XWT08/XWT09 Instruction Manual - Page 8
...
1
3
2
► 1 . An incorrect size impact socket will result in the impact socket is removed before installing the impact socket.
Installing or removing impact socket
Only for Model XWT07,XWT08 (optional accessory) CAUTION: Make sure that the hole in inaccurate and inconsistent fastening torque and/or damage to retain the pin. For impact ...
XWT07/XWT08/XWT09 Instruction Manual - Page 9
... be secured.
Then release the sleeve to the instructions above. NOTE: If the drill bit is not...install the hook, insert it with hoist. Hook 3. Bracket 2. Installing or removing drill bit/ socket adapter
Only for Model XWT09 (optional accessory)
Ring
Only for Model... cartridge all the way until the red part cannot be installed on either side and then secure it into the sleeve as far ...
XWT07/XWT08/XWT09 Instruction Manual - Page 10
... (second) 2. The proper fastening torque may differ depending upon the kind or size of the bolt, the material of the workpiece to be fastened, etc.
Model XWT07 Proper fastening torque for high tensile bolt
2
N•m (ft•lbs)
800 (590)
600 (440)
400 (300)
M24(1″) M24(1″)
M22(7/8″) M22...
XWT07/XWT08/XWT09 Instruction Manual - Page 11
... fastening torque for standard bolt
2
N•m (ft•lbs)
800 (590)
M30(1-1/4″)
M30(1-1/4″)
600 (440)
400 (300)
200 (150)
M24(1″) M24(1″)
Model XWT09 Proper fastening torque for high tensile bolt
2
N•m (ft•lbs)
800 (590)
600 (440)
400 (300)
M24(1″) M24(1″)
M22(7/8″) M22...
XWT07/XWT08/XWT09 Instruction Manual - Page 12
... more details regarding these accessories, ask your local Makita Service Center. • Impact socket • Drill bits (only for 15 minutes before proceeding with your bolt or nut. This Warranty does not apply where: • repairs have been made to you need any trouble develop during this manual.
NOTE: If the tool is thoroughly inspected...
XWT07Z Parts Breakdown - Page 2
Model XWT07Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
251476-6
004
851K73-0
005
266326-2
006
183C08-8
006 D10...-2
H.S.H.BOLT M5X35 WITH WR XWT07 NAME PLATE TAPPING SCREW 4X18 HOUSING SET INC. 43 LED CIRCUIT F/R CHANGE LEVER SWITCH COMPLETE SWITCH PLATE COMPLETE BATTERY HOUSING SET RUBBER PIN 6 INC. 46 PIN 1.5 RUBBER PIN 5 CUSHION RUBBER...
Makita XWT07Z/XWT07M New Tool Flyer English - Page 1
... XWT07M UPC Code XWT07Z
3/4" 0 - 900 / 0 - 1,000 / 0 - 1,800 RPM 0 - 1,800 / 0 - 2,000 / 0 - 2,200 IPM
780 ft.lbs. 9"
18V LXT® Lithium-Ion 8.1 lbs.
088381-803359 088381-803335
OPTIONAL ACCESSORIES
n 18V Lithium-Ion Dual Port Rapid Optimum Charger (DC18RD) n 18V Lithium-Ion 4-Port Charger (DC18SF) n 18V LXT® Lithium-Ion 5.0Ah Battery (BL1850B)
All specifications subject to optimize...
Makita XWT07Z Reviews
We have not received any reviews for Makita yet.