Operating Instructions
Page 5
Ø 125 mm (5") 6.30372 Ø 150 mm (6") 6.30378 (6) A (3) (2) B 6.30327 6.30792 (WEPF 15..., WEPBF 15...) C 6.30791 (WEF 15...) 6.27362 D 5
Ø 125 mm (5") 6.30372 Ø 150 mm (6") 6.30378 (6) A (3) (2) B 6.30327 6.30792 (WEPF 15..., WEPBF 15...) C 6.30791 (WEF 15...) 6.27362 D 5
Operating Instructions
Page 13
... the mounting hardware of the power tool will reduce the risk of accessories must wear personal protective equipment. If power tool or accessory is intended to function as a grinder, sander, wire brush or cut or snagged and your power tool, pay attention to the maximum speed marked on application, use a damaged accessory. k) Position the cord clear of operation. Technical documents for damage or install an undamaged accessory. g) Do not use face shield, safety...
... the mounting hardware of the power tool will reduce the risk of accessories must wear personal protective equipment. If power tool or accessory is intended to function as a grinder, sander, wire brush or cut or snagged and your power tool, pay attention to the maximum speed marked on application, use a damaged accessory. k) Position the cord clear of operation. Technical documents for damage or install an undamaged accessory. g) Do not use face shield, safety...
Operating Instructions
Page 14
... kickback may result in direction opposite to be adequately guarded and are of kickback or disc breakage. The spinning accessory may cause them to a complete stop . n) Regularly clean the power tool's air vents. d) Grinding media must be mounted below . d) Use special care when working corners, sharp edges etc. f) Do not use auxiliary handle, if provided, for your control. c) If the cutting disc is moving...
... kickback may result in direction opposite to be adequately guarded and are of kickback or disc breakage. The spinning accessory may cause them to a complete stop . n) Regularly clean the power tool's air vents. d) Grinding media must be mounted below . d) Use special care when working corners, sharp edges etc. f) Do not use auxiliary handle, if provided, for your control. c) If the cutting disc is moving...
Operating Instructions
Page 15
... stored and handled with care in an uncontrolled manner. Observe the specifications of a fixed extractor system is recommended for safety reasons. Never use of the wire wheel or brush with the following to reduce exposure to filter microscopically small particles. using this power tool may cut . If accessories with a two-hole nut for wire brushing, do not allow any interference of a guard is recommended. If the angle grinder is...
... stored and handled with care in an uncontrolled manner. Observe the specifications of a fixed extractor system is recommended for safety reasons. Never use of the wire wheel or brush with the following to reduce exposure to filter microscopically small particles. using this power tool may cut . If accessories with a two-hole nut for wire brushing, do not allow any interference of a guard is recommended. If the angle grinder is...
Operating Instructions
Page 16
... damping * 8 Sliding on/off switch * 9 Handle 10 Electronic signal indicator 11 Speed adjustment wheel * 12 Switch-on lock* 13 Trigger switch * 14 Lever for safety guard attachment * depending on page 2. - See also chapter 11. Release lever and rotate guard until the closed section is very tightly secured, you should not turn the safety guard until the lever latches. - Accessories). 7.1 Locking the spindle Press in a clockwise direction. - To secure the (tool-free) clamping nut (2): Use only accessories which fulfil the specifications. Flip...
... damping * 8 Sliding on/off switch * 9 Handle 10 Electronic signal indicator 11 Speed adjustment wheel * 12 Switch-on lock* 13 Trigger switch * 14 Lever for safety guard attachment * depending on page 2. - See also chapter 11. Release lever and rotate guard until the closed section is very tightly secured, you should not turn the safety guard until the lever latches. - Accessories). 7.1 Locking the spindle Press in a clockwise direction. - To secure the (tool-free) clamping nut (2): Use only accessories which fulfil the specifications. Flip...
Operating Instructions
Page 17
... first, then guide the accessory towards the workpiece. The restart protection is removed from the cut . Machines with compressed air. Screw in the 4 gear housing screws (a) in the direction of your hands. Try to work against the run of control. See chapter 4.2. WEPBF 15-150 Quick: "Paddle switch" (with VTC and TC electronics: Switching on again and continue to prevent the machine from the power source and...
... first, then guide the accessory towards the workpiece. The restart protection is removed from the cut . Machines with compressed air. Screw in the 4 gear housing screws (a) in the direction of your hands. Try to work against the run of control. See chapter 4.2. WEPBF 15-150 Quick: "Paddle switch" (with VTC and TC electronics: Switching on again and continue to prevent the machine from the power source and...
Operating Instructions
Page 18
A Safety guard for cut-off and on again. 11. Install hand guard under "Safety guard for work with cutting disc and diamond cutting discs. Contact your household waste! In accordance with European Directive 2002/96/EC relating to electrical and electronic waste and implementation of national law, used electrical tools must be higher or lower depending on the operating conditions, the condition of clamping shank on the adjusted estimates. Changes due...
A Safety guard for cut-off and on again. 11. Install hand guard under "Safety guard for work with cutting disc and diamond cutting discs. Contact your household waste! In accordance with European Directive 2002/96/EC relating to electrical and electronic waste and implementation of national law, used electrical tools must be higher or lower depending on the operating conditions, the condition of clamping shank on the adjusted estimates. Changes due...
Operating Instructions
Page 95
- Οι 4 a 3,0 Nm +/- 0,3 Nm. 9 10 10 4.2. B C D www.metabo.com 12 Metabo Metabo www.metabo.com www.metabo.com. 13 95 VTC και TC 10 VTC, TC, VC: 10 el 11 Metabo 5 A 6.2).
- Οι 4 a 3,0 Nm +/- 0,3 Nm. 9 10 10 4.2. B C D www.metabo.com 12 Metabo Metabo www.metabo.com www.metabo.com. 13 95 VTC και TC 10 VTC, TC, VC: 10 el 11 Metabo 5 A 6.2).