NEC V754Q Support and Manuals
NEC V754Q Videos
Popular NEC V754Q Manual Pages
External Controls - Page 10
... will reply with this message for a confirmation of the "Set parameter message".
Operation code table". Usually, this "command message" is as follows,
STX OP code OP code
Set Value
ETX
page
Hi Lo Hi Lo MSB
LSB
Refer to section 5.3 "Set parameter" for more details.
4) Set Parameter reply
The monitor replies with the status of the...
External Controls - Page 22
IV.
The controller requests the Monitor to reply with current Backlight setting and capability to support this operation.
Monitor ID: Indicate a replying Monitor ID. Step 1. Ex.) When this operation. (Get parameter)
Header SOH-'0'-Monitor ID-
'0'-'C'-'0'-'6'
Message STX-'0'-'0'-'1'-'0'-ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of packet
Step 2. Control Commands ...
External Controls - Page 23
... Start of which you want to change a setting. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Set Backlight setting 80(0050h).
The controller request the monitor to change the Backlight setting
Header
SOH-'0'-Monitor ID'0'-'E'-'0'-'A'
Message
STX-'0'-'0'-'1'-'0''0'-'0'-'5'-'0'-ETX...
External Controls - Page 25
...Delimiter CR
Header SOH (01h): Start of Message '0'-'0' (30h, 30h): Result code. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is "Set parameter" type. '0'-'0'-'0'-'3' (30h, 30h, 30h, 33h): Number of Message
Check code BCC: Block Check Code Refer to read . The controller can monitor inside temperatures by using those sensors with external...
External Controls - Page 26
... 79h (in the page 2). '0'-'0' (30h, 30h): This operation is "Set parameter" type. 'F'-'F'-'F'-'F' (46h, 46h, 46h, 46h): Maximum value. '0'-'0'-'3'-'2' (30h, 30h, 33h, 32h): The temperature is the controller. Message STX (02h): Start of packet
Step 3. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2).
Header
SOH...
External Controls - Page 52
... not set. 0004: OFF (same as the power off by IR) ETX (03h): End of Message
Check code BCC: Block Check Code Refer to change a setting. Ex.) When this byte is set . ...Command". '0'-'C (30h, 43h): Message length is encoded as ASCII characters '2' and '0' (32h and 30h). No error. 'C'-'2','0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command The monitor replies ...
External Controls - Page 55
...30h): Message receiver is "Command". Ex.) When this byte is set to the monitor at a time is 32bytes. The data must ...
(55/145) Data(0) -- The data must be ASCII characters strings. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write command '0'-'0'(30h, .... 00h : Write data into from top of Message '0'-'0': Result code. Delimiter CR (0Dh): End of the Asset data area. 8.2...
External Controls - Page 125
...,41h): Message length (10byte)
Message
STX (02h): Start of Message 'C'-'B'-'0'-'9' (43h, 42h, 30h, 39h): Setting Copy Reply '0'-'2' (30h, 30h): Start ST: Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of packet
2) The monitor replies to the section 4.3 "Check code" for a BCC calculation.
Monitor ID: Indicate a replying Monitor ID. 23...
Users Manual - English - Page 3
... information on each software, see "readme.pdf" inside the "about GPL&LGPL" folder on a circuit different from that interference will not occur in a residential installation. Operation is no guarantee that to which can radiate radio frequency energy, and, if not installed and used in this manual. Responsible Party: NEC Display Solutions of America, Inc.
CRESTRON...
Users Manual - English - Page 7
... in Specification (see "V654Q" on page 72, "V754Q" on...parts and then secure the monitor with the installation instructions. Maintenance
• Periodically check for loose screws, gaps, distortions, or other accessories. If a problem is strongly recommended to mount the unit.
For NEC Qualified Personnel:
Stability Hazard. The device may happen due to qualified personnel for service...
Users Manual - English - Page 9
...position, the NEC logo ornament position can use 600 mm/400 mm holes for use only.
Ensure the handles are for installing the logo ...set position. : Alternate position.
Attaching the logo ornament: make sure the holes for the screws on the logo ornament and the holes for mounting
This model is larger than the monitor's screen area, on a flat even surface that can easily support...
Users Manual - English - Page 21
...device, or contact your supplier for the USB setting. USB MP:
USB downstream port (Type-A). ... connected to the specifications page for power supply, please use a USB cable that supports 2A.
•... use this case, please check user's manual of the monitor or shutting down Windows...USB CM2 are not corresponding port.
USB CM2:
Service port.
Connect a USB compatible flash memory or...
Users Manual - English - Page 27
... REPEAT AUDIO FILE BGM PLAY END SCREEN
Function Selects ACTUAL SIZE or BEST FIT. FOLDER
Select a file by SET/POINT ZOOM button and confirm by ENT button. If OK is "MANUAL". Sets interval time.
Selects a setting for when the slideshow finishes. PRESET CONTENTS Plays selected folder when the monitor has no signal input...
Users Manual - English - Page 58
... Network Password Settings
Click on "NETWORK SERVICE" on ...password, consult your password.
Name Settings
Click on "NAME" on the left column below HOME. The name must be max. 16 characters long.
Set a password for the HTTP server. The device supports...PASSWORD An HTTP PASSWORD is the model name. The default is required when logging into the HTTP server. The password must be set...
Users Manual - English - Page 60
... on when HDMI CEC devices are turned on, the monitor connected to MUTE automatically. The Volume button on . By selecting a device name, the HDMI CEC supported device input switches to a device supporting HDMI CEC.
Setting
To set to the devices by wireless remote control and pressing the play . buttons select ON then press...
NEC V754Q Reviews
Do you have an experience with the NEC V754Q that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!