Netgear AGM731F - ProSafe SFP Transceiver Module Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear AGM731F manuals!
Problems with Netgear AGM731F?
Ask a Question
Free Netgear AGM731F manuals!
Problems with Netgear AGM731F?
Ask a Question
Popular Netgear AGM731F Manual Pages
AGM731F Product specification - Page 2
... 62.5/125µm Multi Mode Fiber
2 Rev. 0A
The optical power levels, under normal operation, are at eye safe level. The transceiver is a Class 1 eye safety product.
The transceiver is also compatible with industry standard RFT connector and cage. It is hot pluggable 3.3V Small-Form-Factor transceiver module designed expressly for IEEE...
AGM731F Product specification - Page 4
...-pk) Relative Intensity Noise
tr /tf TJTX RIN
260
psec
1
220
psec
-117 dB/Hz
Output Eye Receiver
Complies with the IEEE 802.3z/D2 specification, and is provided at a BER of 1×10-10 or better with an input signal consisting of the eye diagram for the optical transmit signal...
AGM731F Product specification - Page 5
SFP Transceiver Electrical Pad Layout
Pin Function Definitions
Pin Num. 1 2
Name VeeT TX Fault
Function Transmitter Ground Transmitter Fault Indication
Plug Seq. 1 3
3
TX Disable Transmitter Disable
3
4
MOD-DEF2 Module Definition 2
3
5
MOD-DEF1 Module Definition 1
3
6
MOD-DEF0 Module Definition 0
3
7
Rate Select Not Connect
3
8
LOS
Loss of Signal
3
9
VeeR
Receiver ...
AGM731F Product specification - Page 6
...-coupled, differential lines with a 4.7 - 10 K Ω resistor. When the recommended supply-filtering network is used, hot
plugging of the SFP transceiver module will accept differential swings of 500 - 2400 mV (250 - 1200
mV single-ended), though it is recommended that is used to < 0.8V.
2) TX disable is an input that values between 370...
AGM731F Product specification - Page 7
Package Outline Drawing for Metal Housing with Bail de-latch
AGM731F 850nm 1.25GBd 1000Base-SX / LC Connector
Class 1 Laser Proudct
R
272-10254-02
Complies with 21 CFR 1040.10 and 1040.11 Made in China
7 Rev. 0A
AGM731F Product specification - Page 8
...sec when the optical output falls below 10% of
nominal
Time from falling edge of TX_DISABLE to
msec when the modulated optical output rises
above 90% of nominal
From power on or negation of TX_Fault using 300 msec
TX Disable.
100...;sec Time from non-LOS state to Rx LOS deassert 100 kHz
8 Rev. 0A
SFP timing parameters for SFP management
Parameter
TX_DISABLE Assert time
Symbol t_off
Min.
AGM731F Product specification - Page 9
... fault condition
Unsuccessful recovery from safety fault condition
Timing of LOS detection
9 Rev. 0A Example of initialization during hot plugging, SFP TX_DISABLE timing during hot plugging of SFP TRANSCEIVER. SFP timing parameters
Power on initialization of SFP transceiver, TX_DISABLE Power on initialization of SFP, TX_DISABLE asserted
negated
Initialization during normal operation.
AGM731F Product specification - Page 10
...
74 SN
99 00
124 00
Notes:
1) Byte 63: Check sum of bytes 0-62.
2) Byte 68-83 (SN): Serial number.
3) Byte 84-91 (DC): Date code.
4) Byte 95 (CS2): Check sum of bytes 64-94. 5) Byte 128-255 had been set hex. 00.
10 Rev. 0A
AGM731F Product specification - Page 11
... Electromagnetic Field
EN 61000-4-3 IEC 61000-4-3
Electrostatic Discharge to the EN 61000-4-2
Duplex LC Receptacle IEC 61000-4-2
IEC 801.2
(1) Satisfied with electrical characteristics of product spec.
(2) No physical damage
Electrostatic Discharge to the Electrical Pins
MIL-STD-883E Method 3015.7
Eye Safety
US FDA CDRH AEL Class 1
CDRH File # 0321539-00...
AGM731F Product specification - Page 12
... with Innovation,
FrontView, IntelliFi, PowerShift, ProSafe, RAIDar, RAIDiator, X-RAID, RangeMax, ReadyNAS and Smart Wizard are for identification purposes
only and may be trademarks of
NETGEAR, Inc. Information is subject to change without notice. Other brand names mentioned herein are trademarks of their respective holder(s).
D-AGM731F-0 All rights reserved. © 2008...
Netgear AGM731F Reviews
We have not received any reviews for Netgear yet.