Oki X400 Support and Manuals
Popular Oki X400 Manual Pages
T400, T410, X400 Safety, Warranty and Regulatory Information (English, Fran栩s, Espa?ol, Portugu鱩 - Page 2
...repair work. If the cord becomes damaged or frayed, replace ...8226; Place your product serviced by all warning and instruction labels on the product...to defeat the grounding.
• Install the product near water. Do not... read the provided setup and operating instructions.
• Save...instructions.
2 -
Safety, Warranty and Regulatory Information
Safety Information, 120-Volt Models...
T400, T410, X400 Safety, Warranty and Regulatory Information (English, Fran栩s, Espa?ol, Portugu鱩 - Page 4
...or installation,...model and serial numbers of the warranted item.
The Product to you .
Overnight Exchange US and Canada Only
Oki Data offers Overnight Exchange of the exchange unit.
A written receipt for pickup by Oki Data or its functional equivalent, at its option, replace, with the exchange product.
If they determine that your local Oki Data authorized service...problem...
T400, T410, X400 Safety, Warranty and Regulatory Information (English, Fran栩s, Espa?ol, Portugu鱩 - Page 5
If you have a problem that you purchased your machine • Error message interpretation/solutions • Parts and supplies identification • Consumer relations
Note: Customer Support Representatives are available 24 hours a day, 7 days a week. Mt. Just take a few minutes setting it up -to state. Get started today by visiting http://MY.OKIDATA.com. Please consult your Oki ...
X400 User's Guide - English - Page 13
... the printer.
Other ribbon/media combinations may or may be installed in the printer when calibrating in the Program.pdf file for further information. See the Programming Guide for details. Selecting the Label Sensor Type
OKIPOS X400 printers can use printer commands to set up the printer mode and sensing method. Refer to the...
X400 User's Guide - English - Page 16
... using Windows, contact our Service Hotline. The file OKIPOS X400 Manual.pdf on the CD-ROM...set up the printer, start your label printing program, and follow its instructions.
You can be ignored even if the ERROR indicator
becomes lit.
This program will change, but should be downloaded free of the manual... output ASCII text (including the control codes). If you need to the printer...
X400 User's Guide - English - Page 18
... or cabling problem. If ERROR and POWER indicators are flashing in the OKIPOS X400 Manual.pdf file ...installed.
3. If you are closed.
4. Print a self-test label as described on both ERROR and POWER indicators are flashing alternately, it means media error (media out or gap was not detected).
2. If these steps do not correct the problems, contact your dealer or our
Technical Support...
X400 User's Guide - English - Page 25
... your dealer for the disk with the driver, enter X:\Drivers\ and select the OKI printer model from the list. It supports all OKI printers. Please contact your computer. Enter X:\START.EXE (where X is opened.
Follow the instructions on the Label Gallery Free CD-ROM included with each OKIPOS X400 printer. Label Gallery Free requires a Pentium based...
X400 User's Guide - English - Page 26
... driver is located in the OKIPOS X400 Printer Programming Guide found on the CD-ROM. Calibration is contained in the Drivers directory on the OKIPOS X400 series Ready-To-Go CD-ROM.
24 The driver can be installed using the Label Gallery Free START.EXE setup wizard or can be configured. These supplies have to give acceptable results. Instructions...
X400 Programming Command Manual - Page 1
TABLE OF CONTENTS
OKIPOS X400 Programming Guide
Introduction 1 The Oki Data Programming Language 1 Selecting Protocol Control Codes 2 Using Basic 2 Printing with the Parallel Port 3 Printing with the RS232 Port 4 The Print Area 4 Rotated Fields 8 Command Default Settings 8 Printer Configuration 9 Label Sensing 9 Command Code Page Reference 10
Barcodes 12 Barcodes, Expansion 17 ...
X400 Programming Command Manual - Page 3
...the internal intelligence of code to be assembled into an organized block of the printer. OKIPOS X400 PROGRAMMING GUIDE
INTRODUCTION
This section ...Codes, contain non-printable ASCII characters (such as one data stream to the printer, which in this format tell the printer to perform a specific action which are referred to most programmers. Typically there are four types of firmware...
X400 Programming Command Manual - Page 11
...models in that lists the active settings in effect until a new command is received. Test Labels can be printed that they do not use eye-mark (black bar), gap or notch label sensing. The parameters that can be configured are:
Sensor Calibration Protocol Codes...and notch sensor is a transmissive or see User's Guide).
COMMAND
DEFAULT
NOTE
Print Rotation
0o
(1)
Vertical Reference...
X400 Programming Command Manual - Page 84
... symbols in the set , when used in a structured append format 1~8. For Domestic US UPS shipments. 3 For Mode 3 Structured Carrier Message. For International UPS shipments. 4 Standard symbol. 5 Not currently supported. 7 Reader programming.
See Appendix B for specific information on a label. c = 2 For Mode 2 Structured Carrier Message. dd...dd 9 digit numeric Postal Code. gg..g = Data...
X400 Programming Command Manual - Page 85
Please refer to UPS Publication "Guide to Bar Coding with UPS Online Version 5" for the UPS secondary message data format requirements and the latest format requirements.
2. Special Notes 1. The following modes are supported.
MODE 2
3
4 6
POSTAL CODE COUNTRY CODE SERVICE CLASS
9 digits max
3 digits max
3 digits max
numeric only
numeric only
numeric only
6 digits fixed
3 digits max...
X400 Programming Command Manual - Page 91
...=25
NULL=2A
OFFLINE=7E
Special Notes 1. Custom Protocol Command Codes Download
Command Structure LD,a,b,c,d,e,f,g,h,i
a = Replacement character for STX in ASCII or hex format b = Replacement character for ETX in ASCII or hex format c = Replacement character for ESC in ASCII or hex format d = Replacement character for ENQ in ASCII or hex format e = Replacement character for CAN in ASCII or hex...
X400 Programming Command Manual - Page 101
... format 1~8. c = 2 For Mode 2 Structured Carrier Message. dd...dd 9 digit numeric Postal Code. eee = 3 digit numeric Country Code. BWaabbb
Bar Code Expansion. BTabbccddee
Bar codes.
specification. For International UPS shipments.
4 Standard symbol.
5 Not currently supported.
8 Reader programming. fff = 3 digit Service Class. Prints a duplicate of Maxicode symbols in the set...
Oki X400 Reviews
Do you have an experience with the Oki X400 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Oki yet.
Earn 750 points for your review!