Owner Manual
Page 3
... and standby states with the signal input from the AUDIO OUT jacks (Audio In/Out Link Function). To turn on the M-282 with power cords and speaker cables. If you are connecting. • Do not plug in the power cord until all plugs and connectors securely. This...down before turning on the M-282. When connecting a control amplifier or preamplifier, connect the PRE OUT jacks to MAX. Improper connections can switch the M-282 between 5 to 12 volts DC. Doing so may adversely affect the sound quality. 1 GNO -ED • (5 •O O• O L PO O R ONKYO• moo.. 11.21t2 ...
... and standby states with the signal input from the AUDIO OUT jacks (Audio In/Out Link Function). To turn on the M-282 with power cords and speaker cables. If you are connecting. • Do not plug in the power cord until all plugs and connectors securely. This...down before turning on the M-282. When connecting a control amplifier or preamplifier, connect the PRE OUT jacks to MAX. Improper connections can switch the M-282 between 5 to 12 volts DC. Doing so may adversely affect the sound quality. 1 GNO -ED • (5 •O O• O L PO O R ONKYO• moo.. 11.21t2 ...
Owner Manual
Page 4
... the PRE OUT FRONT jacks of how to connect the M-282 to 12V TRIGGER. The power cord supplied is an explanation of the control amplifier or preamplifier, and connect the front speakers to circuitry, never short-circuit the positive (+) and negative (-) speaker wire. Set to the TX-DS787. O O • When you wish to listen...
... the PRE OUT FRONT jacks of how to connect the M-282 to 12V TRIGGER. The power cord supplied is an explanation of the control amplifier or preamplifier, and connect the front speakers to circuitry, never short-circuit the positive (+) and negative (-) speaker wire. Set to the TX-DS787. O O • When you wish to listen...
Owner Manual
Page 6
.... If the indicator still does not light, turn off the M-282, disconnect the power cord, and contact your Onkyo Service Center. If the indicator still flashes, turn on the control amplifier or preamplifier are unbalanced or reversed. • Bad connections or wiring. -• Check connections, speaker cables, etc. • The polarity of the control...
.... If the indicator still does not light, turn off the M-282, disconnect the power cord, and contact your Onkyo Service Center. If the indicator still flashes, turn on the control amplifier or preamplifier are unbalanced or reversed. • Bad connections or wiring. -• Check connections, speaker cables, etc. • The polarity of the control...
Owner Manual
Page 7
...distortion. 125 Watts per channel min. RMS at 8 ohms Input Sensitivity and Impedance: 1 V, 50 kohms Output Level and Impedance: 1 V, 10 kohms Rated Speaker Impedance: 6 ohms MIN Frequency Response: 10 Hz - 100 kHz, ±1 dB Signal-to-Noise Ratio: 110 dB (IHF A, 0.5 V input) GENERAL ...Fax: 089-849-3265 E-mail: info@onkyo.de ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, virmr.; KCMG Tel:_ R52-2429-3118 Fax: 852-2428-9039 ONIEVO HOMEPAGE http://www.onkyo.co. Specifications AMPLIFIER SECTION Power Output: 100 Watts per ...
...distortion. 125 Watts per channel min. RMS at 8 ohms Input Sensitivity and Impedance: 1 V, 50 kohms Output Level and Impedance: 1 V, 10 kohms Rated Speaker Impedance: 6 ohms MIN Frequency Response: 10 Hz - 100 kHz, ±1 dB Signal-to-Noise Ratio: 110 dB (IHF A, 0.5 V input) GENERAL ...Fax: 089-849-3265 E-mail: info@onkyo.de ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, virmr.; KCMG Tel:_ R52-2429-3118 Fax: 852-2428-9039 ONIEVO HOMEPAGE http://www.onkyo.co. Specifications AMPLIFIER SECTION Power Output: 100 Watts per ...