Owner Manual
Page 2
...cabinet with the M-282. For heavier dirt, dampen a soft cloth in all critical sections, and 3) incorporating innovative circuit topology based upon decades of high-end amplifier design experience --- Supplied accessory Check that the power supply voltage of the available power supply differs according ...The voltage of the area where this unit will be used as a 2 channel amplifier in a multi room configuration, you can turn on , contact your Onkyo authorized service station. 4. AUTO POWER ON/OFF FUNCTION You can connect several rooms. 1. Recording Copyright Recording of copyrighted...
...cabinet with the M-282. For heavier dirt, dampen a soft cloth in all critical sections, and 3) incorporating innovative circuit topology based upon decades of high-end amplifier design experience --- Supplied accessory Check that the power supply voltage of the available power supply differs according ...The voltage of the area where this unit will be used as a 2 channel amplifier in a multi room configuration, you can turn on , contact your Onkyo authorized service station. 4. AUTO POWER ON/OFF FUNCTION You can connect several rooms. 1. Recording Copyright Recording of copyrighted...
Owner Manual
Page 3
..., set the TRIGGER switch to AUDIO (Auto Power On/Off Function). Improper connection t--- Note: When a plug is connected to the 12V TRIGGER jack, be produced. To turn the volume of the control amplifier or preamplifier down before turning on the M-282. Inserted completely • Do not bind audio...the AUDIO IN jacks on and standby states with operations at the AUDIO IN jacks of the M-282. Doing so may adversely affect the sound quality. 1 GNO -ED • (5 •O O• O L PO O R ONKYO• moo.. 11.21t2 AC INLET 11 II 345 6 7 1 GND Use this GND terminal...
..., set the TRIGGER switch to AUDIO (Auto Power On/Off Function). Improper connection t--- Note: When a plug is connected to the 12V TRIGGER jack, be produced. To turn the volume of the control amplifier or preamplifier down before turning on the M-282. Inserted completely • Do not bind audio...the AUDIO IN jacks on and standby states with operations at the AUDIO IN jacks of the M-282. Doing so may adversely affect the sound quality. 1 GNO -ED • (5 •O O• O L PO O R ONKYO• moo.. 11.21t2 AC INLET 11 II 345 6 7 1 GND Use this GND terminal...
Owner Manual
Page 4
... to these terminals. • Be sure not to the TX-DS787. If a speaker with the M-282. O O NO! The power cord supplied is designed for use a power cord other end is an explanation of the M-282. 1 TX-DS787 ARDOR.. TMGOER It &Me Cer tra'te7,4• SP RS • O O...to both the right and leftchannel terminals simultaneously. When connecting the M-282 to 2 channel control amplifier or preamplifier, connect the AUDIO IN jacks of the M-282 to the PRE OUT FRONT jacks of the control amplifier or preamplifier, and connect the front speakers to the SPEAKERS terminals ...
... to these terminals. • Be sure not to the TX-DS787. If a speaker with the M-282. O O NO! The power cord supplied is designed for use a power cord other end is an explanation of the M-282. 1 TX-DS787 ARDOR.. TMGOER It &Me Cer tra'te7,4• SP RS • O O...to both the right and leftchannel terminals simultaneously. When connecting the M-282 to 2 channel control amplifier or preamplifier, connect the AUDIO IN jacks of the M-282 to the PRE OUT FRONT jacks of the control amplifier or preamplifier, and connect the front speakers to the SPEAKERS terminals ...
Owner Manual
Page 5
... STANDBY/ ON indicator lights orange after flashing red for 5 seconds. If the M-282 is in the standby state and lights orange when the M-282 is factory set to turn off . If the M-282 is in the power cord into the rear panel and wall outlet, pressing this switch differs depending on the...automatically when 12V DC is turned off the M-282. When the TRIGGER switch is set to turn off the M-282. Press the POWER switch to red and the M-282 enters standby state (Auto Power On/Off Function). To use the Auto Power On Function when the power is supplied to AUDIO If no signal is ...
... STANDBY/ ON indicator lights orange after flashing red for 5 seconds. If the M-282 is in the standby state and lights orange when the M-282 is factory set to turn off . If the M-282 is in the power cord into the rear panel and wall outlet, pressing this switch differs depending on the...automatically when 12V DC is turned off the M-282. When the TRIGGER switch is set to turn off the M-282. Press the POWER switch to red and the M-282 enters standby state (Auto Power On/Off Function). To use the Auto Power On Function when the power is supplied to AUDIO If no signal is ...
Owner Manual
Page 6
... or wiring. -o Check connections, speaker cables, etc. • Amplifier protection circuitry has been activated. -o Contact your Onkyo Service Center. • The INPUT LEVEL control is pressed. Power turns on the M-282. Lower the volume at very low volume. • Bad connections or...control amplifier or preamplifier. No power. • The power cord is set to a position other than OFF, the POWER switch is pressed again immediately after turning the power off the M-282, disconnect the power cord, and contact your Onkyo Service Center. A malfunction. -o Press the POWER ...
... or wiring. -o Check connections, speaker cables, etc. • Amplifier protection circuitry has been activated. -o Contact your Onkyo Service Center. • The INPUT LEVEL control is pressed. Power turns on the M-282. Lower the volume at very low volume. • Bad connections or...control amplifier or preamplifier. No power. • The power cord is set to a position other than OFF, the POWER switch is pressed again immediately after turning the power off the M-282, disconnect the power cord, and contact your Onkyo Service Center. A malfunction. -o Press the POWER ...
Owner Manual
Page 7
...: 852-2428-9039 ONIEVO HOMEPAGE http://www.onkyo.co. Dynamic Power Output: 2 x 140 Watts at 8 ohms Total Harmonic Distortion: 0.08 % at rated power IM Distortion: 0.08 % at rated power Damping Factor: 100 at 6 ohms, both channel driven from 1 kHz with no more than 0.1 % total harmonic distortion. Specifications AMPLIFIER SECTION Power Output: 100 Watts per channel min.
...: 852-2428-9039 ONIEVO HOMEPAGE http://www.onkyo.co. Dynamic Power Output: 2 x 140 Watts at 8 ohms Total Harmonic Distortion: 0.08 % at rated power IM Distortion: 0.08 % at rated power Damping Factor: 100 at 6 ohms, both channel driven from 1 kHz with no more than 0.1 % total harmonic distortion. Specifications AMPLIFIER SECTION Power Output: 100 Watts per channel min.