AJD850 User Guide
Page 43
... (IN point) where voice-over editing is pressed. - 43 - The audio signals can be recorded to the channel which the sound is to be recorded. AJ-D850 TV monitor 1 Select INT_VO as the setup menu No. 322 (AUD MEM MODE) setting. 2 Select the same setting for the channel (CH1 or CH2) on...
... (IN point) where voice-over editing is pressed. - 43 - The audio signals can be recorded to the channel which the sound is to be recorded. AJ-D850 TV monitor 1 Select INT_VO as the setup menu No. 322 (AUD MEM MODE) setting. 2 Select the same setting for the channel (CH1 or CH2) on...
AJD850 User Guide
Page 45
... the sound is to be recorded. 7 Enter the IN and OUT points of the AG-A850. - 45 - ANALOGUE AUDIO IN* VIDEO OUT REMOTE IN/OUT AJ-D850 RECORDER CONTROLLER AG-A850 1 Select INT_VO as the setup menu No. 322 (AUD MEM MODE) setting. 2 Select the same setting for the channel (CH1 or... button. 9 While watching the TV monitor, input the audio signals to be recorded between the IN point and OUT point into the VTR. 4 Set the CONTROL switch on the VTR to the REMOTE position. 5 Set the controller's SOURCE selector to AUX1. 6 Press the insert button for the channel (CH1 or CH2) on...
... the sound is to be recorded. 7 Enter the IN and OUT points of the AG-A850. - 45 - ANALOGUE AUDIO IN* VIDEO OUT REMOTE IN/OUT AJ-D850 RECORDER CONTROLLER AG-A850 1 Select INT_VO as the setup menu No. 322 (AUD MEM MODE) setting. 2 Select the same setting for the channel (CH1 or... button. 9 While watching the TV monitor, input the audio signals to be recorded between the IN point and OUT point into the VTR. 4 Set the CONTROL switch on the VTR to the REMOTE position. 5 Set the controller's SOURCE selector to AUX1. 6 Press the insert button for the channel (CH1 or CH2) on...
AJD850 User Guide
Page 46
... INPUT A INPUT B + MIXER CH1 OUT MIXER CH2 OUT MIXER REMOTE IN/OUT AUDIO AUDIO CHI1 IN CHI1 OUT AUDIO CHI2 IN RECORDER AJ-D850 IN Event 1 OUT CH1 Fig. 1 CH2 CH1 Fig. 2 CH2 IN Up to be edited. - 46 - Event 2 CH1 insert start Cross fading by operating the mixer ...
... INPUT A INPUT B + MIXER CH1 OUT MIXER CH2 OUT MIXER REMOTE IN/OUT AUDIO AUDIO CHI1 IN CHI1 OUT AUDIO CHI2 IN RECORDER AJ-D850 IN Event 1 OUT CH1 Fig. 1 CH2 CH1 Fig. 2 CH2 IN Up to be edited. - 46 - Event 2 CH1 insert start Cross fading by operating the mixer ...
AJD850 User Guide
Page 47
... connectors. (The same audio signals will be set the channel on which the signals are to 14. Proceed with the following settings for the unit (AJ-D850). 1. For audio cross channel editing, set up to perform voice-over editing or audio cross channel editing using the audio memory unit...
... connectors. (The same audio signals will be set the channel on which the signals are to 14. Proceed with the following settings for the unit (AJ-D850). 1. For audio cross channel editing, set up to perform voice-over editing or audio cross channel editing using the audio memory unit...
AJD850 User Guide
Page 97
... EAE: AUTO EDIT EON: EDIT ON (MANUAL EDIT) EPV: PREVIEW ERV: REVIEW [STX] data [ETX] This command is for inquiring about the VTR used. It is only the execution message which is listed in this table. • In the case of commands not listed in the table, ER001... (invalid command) is for the return (completion) message, [ACK] is first returned when data is received, and the execution message is subsequently returned. data = AJ-D850 - 97 - data = f w gh mm ss ff f =F w =S gh = CTL: g = SP (20h): for a plus display - (2Dh): for a minus display h = 0 - 9: hours TC: gh = 00 - 23: hours...
... EAE: AUTO EDIT EON: EDIT ON (MANUAL EDIT) EPV: PREVIEW ERV: REVIEW [STX] data [ETX] This command is for inquiring about the VTR used. It is only the execution message which is listed in this table. • In the case of commands not listed in the table, ER001... (invalid command) is for the return (completion) message, [ACK] is first returned when data is received, and the execution message is subsequently returned. data = AJ-D850 - 97 - data = f w gh mm ss ff f =F w =S gh = CTL: g = SP (20h): for a plus display - (2Dh): for a minus display h = 0 - 9: hours TC: gh = 00 - 23: hours...