Panasonic AWRC400N - PAN/TITLT HEAD Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic AWRC400N manuals!
Problems with Panasonic AWRC400N?
Ask a Question
Free Panasonic AWRC400N manuals!
Problems with Panasonic AWRC400N?
Ask a Question
Popular Panasonic AWRC400N Manual Pages
AWRC400N User Guide - Page 2
... generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may be required to provide reasonable protection against harmful interference when the equipment is on the bottom of the FCC Rules.
NO USER SERVICEABLE PARTS INSIDE.
Cet appareil numérique de la classe A est...
AWRC400N User Guide - Page 4
...6 Accessories 6 Precautions for use 6 Installation precautions 7 Parts and their function 8 Installation 12
$ Assembling the pan/tilt head 12 $ Setting the mounting direction switch 14 $ Setting the PCB switches 15 $ Installing the pan/tilt head 16 $ Mounting the camera 17 $ Attaching the wire 18 Replacing the consumable parts 19 Specifications 20
AW-RC400 Cable Compensation Unit 38...
AWRC400N User Guide - Page 6
... consumable parts" (page 19). Replace the lithium battery here.
6 Indoor Pan/Tilt Head AW-PH400
Introduction
≥ The stand-alone indoor pan/tilt head can be rotated through 300 degrees in the vertical direction and 400 degrees in the horizontal direction.
≥ Operations can be performed at the end of its service life...
AWRC400N User Guide - Page 7
... it to strong impact may cause malfunctioning.
≥ Do not turn the unit's rotating part by hand. Use the unit in places where the humidity is less than 32°F...around the monitor when installing the unit.
≥ When mounting the camera on the unit, take sufficient steps to be used if the unit will be set definite movement limits.
7 AW-PH400
Installation precautions
Indoor Pan/...
AWRC400N User Guide - Page 9
...accessories) These parts are used to secure the camera mounting base to the rotary arm.
6 Tally lamp (accessory) This is 2A. Parts and their ...Camera mounting base Mount the convertible camera on ; When the prompter is connected, the pan/tilt head's speed is turned on this base.
: Pan/tilt head mounting holes These four holes are used when installing the pan/tilt head.
; when it is set...
AWRC400N User Guide - Page 10
...connector on the AW-PB504 SDI card or other card installed in the convertible camera. G CONTROL IN IP/RP connector [IP/RP]...control panel. Indoor Pan/Tilt Head AW-PH400
Parts and their function
= Guide pin Use this to determine the direction in ... camera firmly after it is set to be used when the mounting direction of the motorized lens unit. One of the cables described in "Cable specifications...
AWRC400N User Guide - Page 15
... sure to ask your dealer to install the unit.)
$ Setting the PCB switches
The switches on the CONNECTOR PCB will need to be set in accordance with the signals to be transmitted and the equipment to be connected to the pan/tilt head. (The switches are set to support analog/SDI at the factory.)
≥...
AWRC400N User Guide - Page 16
...been installed, mount the camera on it. ≥ When installing ...installing the pan/tilt head on the ceiling
Wire
t
t
❈ When installing the pan/tilt head, do not forcibly turn the rotary head or rotary arm manually...install the unit.)
$ Installing the pan/tilt head
When installing the pan/tilt head, follow the instructions below carefully. For a stand-alone installation
For installation...
AWRC400N User Guide - Page 20
...The tilt range is limited to 190 degrees by the initial setting of camera to change the AW-RP400 setting. Pan range: 400 degrees (approx. ±200 degrees...°C to +60°C)
Ambient operating humidity: 30% to restrictions depending on pan/tilt head. Specifications are approximate.
Genlock input:
BNC Black burst or composite video signal
Prompter input (PROMPTER IN):
BNC Through...
AWRC400N User Guide - Page 22
...INCOM system 1 set Rack-mounting adaptors 2 Mounting screws (M4!8 mm 4
22 NOTE
≥ The AW-RP400 cannot be used to control the model AW-PH300,...the convertible cameras mounted on the pan/tilt heads can be controlled at the same time.
≥ By installing an ... set. ≥ The connection distance between the control panel and
pan/tilt head system can be discarded at the end of its service...
AWRC400N User Guide - Page 23
Parts and their function
$ Front panel A B C D
Pan/Tilt Control Panel AW-RP400 E F GH I 1
2 3
4
J
5
6
K
7 8
9
:
L
AW-RP400
1 EXT CONT ....
23
When an additional AW-RP400 control panel has been installed, set to [OFF], the power supply from the connected pan/tilt heads to the cameras is turned off when the switch is set to OFF.
3 OPERATE [OFF/ON] switch When this control...
AWRC400N User Guide - Page 24
... down by turning it is pressed, the setting is adjusted manually using the IRIS control on the top of... adjust the lens zoom. The pan/tilt head and camera setting can be adjusted by menu settings.
@ HOME button Press this to move even when the...8 SD CARD slot This slot is turned. Pan/Tilt Control Panel AW-RP400
Parts and their function
7 IRIS [AUTO/MANU/LOCK] button Use this to select the...
AWRC400N User Guide - Page 32
... or when a tracing memory operation (record, play or change) is selected automatically, and operation stops. when STOP is cleared from using it with a personal computer, digital camera or other unit as well.
SD CARD setting The menu setting data of this control panel, the preset memory data of the pan/tilt heads and the...
AWRC400N User Guide - Page 38
...five channels up to 500 meters (when the BELDEN 8281 connecting cable or its service life, ask a specialized contractor to dispose of the video channels (input composite ...; It features a 5µs advance function for the sync signals in order to provide easy support for the three Y, Pr and Pb signal channels by means of a single control.
Accessories... camera is to be adjusted separately.
AWRC400N User Guide - Page 59
...by Hirose Electric
Connect to the LENS I/F2 connector on pan/tilt head. Connect to the ZOOM/FOCUS connector on the camera. Cable length: At least 420 mm or so Cable length: At least 500 mm or so
Connector: HR10A-10J-12P...: HR25-9P-20P made by Hirose Electric
Connect to the IRIS connector on lens. Cable specifications
59
When an IASD, WASD or VASD lens (digital drive) made by Canon is used .
Panasonic AWRC400N Reviews
We have not received any reviews for Panasonic yet.