Panasonic FV08VSL3 Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic FV08VSL3 manuals!
Problems with Panasonic FV08VSL3?
Ask a Question
Free Panasonic FV08VSL3 manuals!
Problems with Panasonic FV08VSL3?
Ask a Question
Popular Panasonic FV08VSL3 Manual Pages
FV08VSL3 User Guide - Page 1
FV-08VSL3 FV-10VSL3
2-3
4
4
4
5
5
(Joist Mounting)
6-7
(Wall Mounting)
8
(Cleaning)
9
(Replacement of lamp)
10
11
11
FV08VSL3 User Guide - Page 2
... Engineers (ASHRAE) and the local code authorities.
When the service disconnecting means cannot be vented to the outdoors. Installation work and electrical wiring must be connected to a GFCI (Ground Fault Circuit Interrupter) - Ducted fans must be observed.
These models are used to classify and describe the type of instructions to be followed in order to...
FV08VSL3 User Guide - Page 3
...wall stud must be installed in your local authorities or visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149. Follow all local electrical and safety codes, as well as...area. (Fig.B)
The special-purpose or dedicated parts, such as shown in the instructions. Do not kink the supply wiring.
Do not install with any solid-state speed control device.
Do...
FV08VSL3 User Guide - Page 4
... try to which can radiate radio frequency energy and, if not installed and used in accordance with Part 18 of the FCC Rules as a standard 100W incandescent lamp. ...be installed in compliance with the instructions, may cause undesired operation. If this equipment.
Responsible Party: Customer Support:
Panasonic Corporation of the FCC Rules. These Panasonic ventilating fan models are ...
FV08VSL3 User Guide - Page 6
...purchase the 26 gauge steel Panasonic 4" Oval - 3" Round Reducer from suspension bracket. (Fig.1)
2. Follow all the local electrical safety codes as well as the National Electrical Code(NEC). Squeeze the circular...junction box cover carefully so that the damper can open and close smoothly. 1. Before installation, remove the tape from damper and adaptor, and check that lead wires are not ...
FV08VSL3 User Guide - Page 7
Remove the tape from mounting springs, lead wire, and night lamp before installation as shown in step 2 of Fig.5.
9. Remove the light cover as... into the housing of connector must latch the rib c o m p l e t e l y. ( F i g . 8 )
11.
Install the night lamp and fluorescent lamps. (Fig.6)
10.
Ceiling hole should be aligned with caulk or other mounting spring into the slot as shown in...
FV08VSL3 User Guide - Page 8
....(Fig.10)
3. If not, it will be effect the life of product must be aligned with caulk or other sealant to 5 of INSTALLATION on page 7). Complete the wiring and duct work . Finish the wall work (refer to step 3 to prevent air leakage. WALL
1. Fix the flange of frame ...
FV08VSL3 User Guide - Page 9
....13
Fig.14 Fig.15
9 Remove dust and dirt from fan body.
Remove grille by pulling down the mounting spring in the right side of "Panasonic" logo. Replace grille. The grille should be dry after cleaning.
3. WARNING
CAUTION
1. Wipe dry with kitchen detergent, remove any dirt from fan body using a vacuum cleaner...
FV08VSL3 User Guide - Page 10
....
4W night lamp has threaded base. Remove grille by turning counterclockwise. Replace the 4W night lamp (Max 4W incandescent lamp). (Fig.19 ) Install the fluorescent lamps (Maxlite MLS13GU35 13W) as shown in step 2 and...dirt from light cover and lens, before maintenance(cleaning) or replacement of "Panasonic" logo. (Fig.16)
2.Remove plug connector then pull down the other mounting...
FV08VSL3 User Guide - Page 11
Our efficient, cool-running motors and our fluorescent lamps do not create excessive heat that is a common problem with recessed light fixtures or some competitor's fan/light combination. Fig.21
FV-08VSL3 FV-10VSL3
1.0
22
1.4
30
2x13 2x13
915, 916 and 920.
825
7.7/3.5
918
100
7.7/3.5
11
Our fans and fan/light combination units do not...
Panasonic FV08VSL3 Reviews
We have not received any reviews for Panasonic yet.