Panasonic PT-RZ770BU Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic PT-RZ770BU manuals!
Problems with Panasonic PT-RZ770BU?
Ask a Question
Free Panasonic PT-RZ770BU manuals!
Problems with Panasonic PT-RZ770BU?
Ask a Question
Popular Panasonic PT-RZ770BU Manual Pages
Series Brochure - Page 4
.... 20,000 Hours*4 of brightness performance or extended life. User Operating Mode
In addition to preset operating modes, the PT-RZ970 Series can be required in challenging conditions.
Replacement of parts other than lamp-based projectors over a 20,000-hour*4 maintenance-free projection period.
A failsafe redundancy circuit works to Long Life 3. Light source lifetime...
Operating Instructions - Page 14
... United
States and other parts may vary from the actual product.
ffWindows and Internet Explorer are trademarks or registered trademarks of the projector, screen, and other ... and Crestron RoomView are registered trademarks of the projector with the power cord attached are trademarks of Panasonic Corporation. rrTerm
ffIn this manual, the "Wireless/wired remote control unit" accessory...
Operating Instructions - Page 28
... to enter a password in the menu screen, change the setting, and adjust the level. About your projector
rrControl panel
1
2
3
4
5
6
7
8
1 Power on button Sets the projector to projection mode when the switch on the projector is set to and the power is turned off (standby mode).
2 Power standby button Sets the projector to the state where the projector is turned off...
Operating Instructions - Page 33
... fit full in the screen. Refer to the Installation Instructions of the Ceiling Mount Bracket when installing and setting up rrAngle sensor The range of the projected image
(Unit: m)
ENGLISH - 33 ffRefer to "For the Fixed-focus Lens (Model No.: ET‑DLE030)" (x page 34) for this projector.
ffBe sure to the projected image size and...
Operating Instructions - Page 61
... Switching on/off the projector
ffTo set the projector based on the installation mode. Consult your dealer for details. Refer to "Installation mode" (x page 32) for details.
After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu → [PROJECTION METHOD].
1) Press qw to as the runtime when you use is set to [AUTO] or [PC...
Operating Instructions - Page 109
... hold for the position of the menu screen (OSD). 1) Press as to display the input guide in [OSD POSITION].
ffThe items will switch each time you press the button.
[1]
Sets to yellow.
[2]
Sets to blue.
[3]
Sets to white.
[4]
Sets to green.
[5]
Sets to peach.
[6]
Sets to switch the item. ENGLISH - 109 Note
ff Even if [ON] is...
Operating Instructions - Page 126
... allowance for [User name] and [Password] as to the latest status information. Yellow: There is an allowance for the projector in red, and press the button to display the error details. 8 Update to select the projector displayed in error. ff The projector is included in all projectors.
10) Set [LIGHT OUTPUT] of all linked projectors.
gg Are the same [LINK...
Operating Instructions - Page 129
... select [DATE AND TIME]. 2) Press the button. ffThe setting of the Panasonic twisted-pair-cable transmitter to the specified input.
*1 Only for PT‑RZ770, PT‑RZ660
*2 When the optional DIGITAL LINK output supported device (Model No.: ET‑YFB100G, ET‑YFB200G) is connected to the projector, its input name is displayed.
3) Press as to...
Operating Instructions - Page 130
... Chapter 4 Settings - [PROJECTOR SETUP] menu
...replacement of the date and time will switch each program.
1) Press as to select [SCHEDULE].
2) Press qw to each time you press the button.
[OFF] [ON]
Disables the schedule function. Note
ff When [SCHEDULE] is set to [ON] while the [PROJECTOR SETUP] menu → [STANDBY MODE] is set to [ECO], the [STANDBY MODE] setting is set a program
Set...
Operating Instructions - Page 145
...password and then continue operations of initialization.
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1) Press as to the side. ff An error... the security password entry.
Set it to "Navigating through the menu" (x page 74) for the first time
Initial password: Press awsqawsq in the factory default setting or when the [PROJECTOR SETUP] menu →...
Operating Instructions - Page 147
... above
*1 SDI input is supported only for approx. 10 seconds. ffThe confirmation screen is displayed.
10) Press qw to [RGB1]. Note
ff When a button operation is performed on the remote control are set to [DISABLE], the projector cannot be set .
[POWER BUTTON]
[INPUT SELECT BUTTON]
[MENU BUTTON] [LENS BUTTON] [AUTO SETUP BUTTON] [SHUTTER BUTTON] [ON...
Operating Instructions - Page 150
... .
ff [NETWORK SETUP] cannot be connected, set to [ON] when connecting the "XTP transmitter" of AMX Corporation. Set to [ON] to control with the PJLink protocol. Refer to [OFF] when connecting the optional DIGITAL LINK output supported device (Model No.: ET‑YFB100G, ET‑YFB200G). Set to [ON] to change the projector name. Set to "Control commands...
Operating Instructions - Page 158
...the [NETWORK] menu → [NETWORK CONTROL] → [WEB CONTROL] to use this manual depending on the purpose. Item [Status] [Projector control] [Detailed set up]
[Change password] [Crestron Connected(TM)]
Function [Projector status] Error information page [Network status] [Access error log]
[Mail error log] [Basic control] [Detail control] [Network config] [Adjust clock]
[Ping test] [E-mail...
Operating Instructions - Page 180
... (below 90 V) Battery replacement for error and warning" (x page 181). ENGLISH The following list shows the alphanumeric symbol that is displayed only with the numeric value. The input supply voltage is displayed when an error or a warning has occurred and its details.
Confirm "Action number", and follow the measure in the [PROJECTOR SETUP] menu →...
Operating Instructions - Page 193
... character codes.
ff If an invalid parameter is sent, the "ER402" response is set to the computer only in Step 2). When multiple projectors are all controlled When controlling multiple projectors together using parameter)
*1 When transmitting a command which does not need a parameter, an operation (E) and parameter are daisy chain connected in RS‑232C supports ZZ...
Panasonic PT-RZ770BU Reviews
We have not received any reviews for Panasonic yet.