Panasonic VLGC001AS - DOOR STATION Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic VLGC001AS manuals!
Problems with Panasonic VLGC001AS?
Ask a Question
Free Panasonic VLGC001AS manuals!
Problems with Panasonic VLGC001AS?
Ask a Question
Popular Panasonic VLGC001AS Manual Pages
VLGC001A User Guide - Page 1
Door Station
Installation and Operation Guide
Model No. Please read this Installation and Operation Guide before using the unit and save for purchasing a Panasonic Door Station. PFQX2165ZA DC0405NK0 VL-GC001A
Thank you for future reference.
VLGC001A User Guide - Page 2
Table of Contents
Important Information
Important safety instructions 3 Additional safety information 4 For best performance 4
Introduction and Installation
Included items 5 Location of controls 6 Before installation 7 Installing the door station 9
Help
Cleaning 13
General Information
Technical data about this product 14 FCC and Other Information 15
2
VLGC001A User Guide - Page 3
... a triangle is intended to tell the user that important operating and servicing instructions are provided for ventilation and to ensure reliable operation of electric shock to .
4) Follow all instructions. SAVE THESE INSTRUCTIONS
3 All warnings on a bed, sofa, rug, or other similar surface.
8) Do not install near any heat sources such as power- All the safety...
VLGC001A User Guide - Page 4
... impairment. 10. Only a qualified technician is allowed to connect a power cable to an authorized service center when the following conditions occur: A. When existing chime wires are not sure of the type...15. Do not make any wiring connections when the power supply is required. Be sure to install the unit as loud sounds emitted from power outlets if it is subsequently used , it ...
VLGC001A User Guide - Page 5
Item 1 Door station 2 Mounting bracket 3 Wood screws
4 Allen wrench 5 Bolt covers
Quantity 1 1 2
1 2
Notes ------ Attached to rear of the door station.
Included items
1
2
5
Introduction and Installation
3
4
No. For the door station. (3.8 mm x 20 mm, 1/8" x13/16")
-----One for spare.
5
VLGC001A User Guide - Page 6
... lever L The camera angle can press this button to drain. D Speaker E Water drain hole L This hole ... the display of the visitor will be adjusted when installing the door station (page 7, 10).
6 Introduction and Installation
Location of controls
Front view
A
Rear view
F
B C D
E
A Camera L When a visitor presses the Call Button, the camera will turn on and an image of the monitor station...
VLGC001A User Guide - Page 7
...")
500 mm 60°
R
(1911/16")
1450 mm (571/16")
500 mm (1911/16")
L Top view of when the camera is facing the left at 0°. Image range: 650 mm (259/16")
L
R
7 Standard installation position of the door station and camera range
Upper/lower range
Left/right range
L Side view of when the...
VLGC001A User Guide - Page 8
... CAT-3 24 AWG Distance: Maximum 100 m (about 328 feet)
8 Where the background is the sky. -
Where echoing occurs, causing the unit to water. Introduction and Installation
Note: L The measurements and angles are for reference purposes and may not be distinguishable. Do not place the door station in the following locations. -
VLGC001A User Guide - Page 9
... the rear of the door station, there is not a screw to drain. L The pin hole camera is a hole to allow water to be touched or removed. Mounting bracket
Pin hole camera
Hex-head screw (Attached to install the door station on a flat, vertical wall. Important information: On the bottom surface of the door...
VLGC001A User Guide - Page 10
.../16")
Wall
3 Connect the wires that connect to the monitor station to the wall using the camera angle control lever.
L Before drilling, see page 7 for the wire type and distance. See page 7 for
details. Introduction and Installation
2 Attach the mounting bracket to the terminal connector by
unscrewing the screws, pushing in the...
VLGC001A User Guide - Page 11
Rib Wire hole
4 Mount the door station to connect the wires without them going through a hole in the wall behind the mounting bracket, connect the wires by passing them through the ribs and the wire hole. Introduction and Installation
L If you want to the mounting bracket.
1
2 Push the door station down until it is secure.
11
VLGC001A User Guide - Page 12
L Use protrusion on the shorter end of the allen wrench. Allen wrench
12 Introduction and Installation
5 Insert the hex-head screw using the shorter end of the allen wrench.
Hex-head screw Allen wrench
6 Attach the bolt cover using the longer end of the allen wrench to rotate the bolt cover until it is secure.
VLGC001A User Guide - Page 14
...)
Aluminum
*1 Supplied from the actual
product.
14 L The pictures and illustrations in these instructions may vary slightly from the monitor station. General Information
Technical data about this product
Power supply*1:
Dimensions:
Mass (Weight): Operating environment:
Installation method: External material:
Standby: Approximately 5 V DC (2 mA) At operation: Approximately 20 V DC (180...
VLGC001A User Guide - Page 15
... which can radiate radio frequency energy and, if not installed and used in accordance with Part 15 of the following two conditions: (1) This device ...installation. Reorient or relocate the receiving antenna. - CAUTION: Any changes or modifications not expressly approved by one or more of the FCC Rules. General Information
FCC and Other Information
This device complies with the instructions...
VLGC001A User Guide - Page 16
..., Inc. All other reproduction, in whole or in part, is copyrighted by Panasonic Communications Co., Ltd., and may be
reproduced for internal use only. Copyright: L This material is prohibited without the written consent of North America One Panasonic Way, Secaucus, New Jersey 07094, U.S.A. All Rights Reserved. San Gabriel Industrial Park, Ave. 65 de...
Panasonic VLGC001AS Reviews
We have not received any reviews for Panasonic yet.