WVCW964 User Guide
Page 1
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Color CCTV Camera Operating Instructions WV-CW964 Model No.
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Color CCTV Camera Operating Instructions WV-CW964 Model No.
WVCW964 User Guide
Page 4
... CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION BEING PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE-CAMERA's PICTURE, INCLUDING SAVED DATA, FOR SOME REASON, BECOMES PUBLIC OR IS USED FOR THE PURPOSE OTHER THAN SURVEILLANCE. (7) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, ANY LOSS OR...
... CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION BEING PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE-CAMERA's PICTURE, INCLUDING SAVED DATA, FOR SOME REASON, BECOMES PUBLIC OR IS USED FOR THE PURPOSE OTHER THAN SURVEILLANCE. (7) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, ANY LOSS OR...
WVCW964 User Guide
Page 5
..., by replaying the stored parameters complicated move-ments are done automatically. ■ Camera Position Memory The system can be configured with up on the dome cover.*1 ■ Waterproofing Specifications Outdoor enclosure based on IP66*2 of IEC60529 standard. *1 Does not operate in environments ...with the power on continuously to keep the temperature inside the camera over -40 °C {-40 °F} defrosting may not...
..., by replaying the stored parameters complicated move-ments are done automatically. ■ Camera Position Memory The system can be configured with up on the dome cover.*1 ■ Waterproofing Specifications Outdoor enclosure based on IP66*2 of IEC60529 standard. *1 Does not operate in environments ...with the power on continuously to keep the temperature inside the camera over -40 °C {-40 °F} defrosting may not...
WVCW964 User Guide
Page 6
.... 10. Please ask the nearest service center about replacement and maintenance of the installation surface and structure. Do not install the camera in an extreme environment where high temperature or high humidity exists. Do not attempt to the product specifications for business transaction or ...security, or malfunctioning of the camera falling down , causing injury to persons and damage to corrosive gasses, e.g., in such places as the lens-drive motors, cooling ...
.... 10. Please ask the nearest service center about replacement and maintenance of the installation surface and structure. Do not install the camera in an extreme environment where high temperature or high humidity exists. Do not attempt to the product specifications for business transaction or ...security, or malfunctioning of the camera falling down , causing injury to persons and damage to corrosive gasses, e.g., in such places as the lens-drive motors, cooling ...
WVCW964 User Guide
Page 7
...location where it is changed from the cloth before cleaning the lenses. (Lenses do if OVER HEAT appears on the display. Even if the camera position is not directly exposed to noise on the monitor and divergence of the concentrated light will remain on one spot for a long period ...can cause blooming (rainbow around the strong light) or smearing (vertical stripes above and below the camera A circular object appears in a food preparation area and other locations where there are subject to clean the lens. Such conditions create the risk of...
...location where it is changed from the cloth before cleaning the lenses. (Lenses do if OVER HEAT appears on the display. Even if the camera position is not directly exposed to noise on the monitor and divergence of the concentrated light will remain on one spot for a long period ...can cause blooming (rainbow around the strong light) or smearing (vertical stripes above and below the camera A circular object appears in a food preparation area and other locations where there are subject to clean the lens. Such conditions create the risk of...
WVCW964 User Guide
Page 8
... and restore normal operation. This can cause malfunction of external noise. ■ Downloading (saving) or uploading (recovering) camera setting information Camera setting information that can be downloaded to other reason continues for more information, see the "Panasonic CCTV System Catalogue" or consult your retailer. -8- However, the following items are not included. • Patrol...
... and restore normal operation. This can cause malfunction of external noise. ■ Downloading (saving) or uploading (recovering) camera setting information Camera setting information that can be downloaded to other reason continues for more information, see the "Panasonic CCTV System Catalogue" or consult your retailer. -8- However, the following items are not included. • Patrol...
WVCW964 User Guide
Page 9
... Auto Night time Switching to Black and White Mode 5 ■ Digital Flip 5 ■ Privacy Zone Function 5 ■ Patrol Function 5 ■ Camera Position Memory 5 ■ Motion Detection 5 ■ Internal Heating Fan 5 ■ Waterproofing Specifications 5 STANDARD ACCESORIES 5 PRECAUTIONS 6 OPERATING PRECAUTIONS 7 CONSTRUCTION... 23 ■ Preset Position Settings 23 ■ Language Setting 25 ■ Advanced Menu Settings 25 CAMERA SETTINGS 26 ■ Using the Camera Setup Menu 26 PAN/TILT SETTINGS 31 ■ Using the Pan/Tilt Setup Menu 31 ALARM SETTINGS ...
... Auto Night time Switching to Black and White Mode 5 ■ Digital Flip 5 ■ Privacy Zone Function 5 ■ Patrol Function 5 ■ Camera Position Memory 5 ■ Motion Detection 5 ■ Internal Heating Fan 5 ■ Waterproofing Specifications 5 STANDARD ACCESORIES 5 PRECAUTIONS 6 OPERATING PRECAUTIONS 7 CONSTRUCTION... 23 ■ Preset Position Settings 23 ■ Language Setting 25 ■ Advanced Menu Settings 25 CAMERA SETTINGS 26 ■ Using the Camera Setup Menu 26 PAN/TILT SETTINGS 31 ■ Using the Pan/Tilt Setup Menu 31 ALARM SETTINGS ...
WVCW964 User Guide
Page 10
..., it replaced. -10- In order to have it could mean that the slip ring has reached the end of noise. CONSTRUCTION Camera Safety Wire Alarm Input Connector Alarm Output Connector Video Output Connector Data Port Power Cord for transmission of electrical power and signals. A ...dirty slip ring can cause deterioration of picture quality during panning and generation of its service life. Ensuring Trouble-free Operation • This camera uses a "slip ring" for Heater Power Connector Attachment Pipe Upper Base Rear sun shield (provided) Front sun shield (provided) Sun shield (...
..., it replaced. -10- In order to have it could mean that the slip ring has reached the end of noise. CONSTRUCTION Camera Safety Wire Alarm Input Connector Alarm Output Connector Video Output Connector Data Port Power Cord for transmission of electrical power and signals. A ...dirty slip ring can cause deterioration of picture quality during panning and generation of its service life. Ensuring Trouble-free Operation • This camera uses a "slip ring" for Heater Power Connector Attachment Pipe Upper Base Rear sun shield (provided) Front sun shield (provided) Sun shield (...
WVCW964 User Guide
Page 11
... of fire, electric shock, personal injury, and material damage. ■ Camera Installation Location Install the camera on a boat, or other areas subject to strong vibration (This camera is not designed for use in the camera, Panasonic holds absolutely no responsibility for use in a vehicle.) • Near an... . ■ Noise interference considerations When using a power line that is greater than 1 meter, wiring should be performed again. If the camera is installed when humidity is very high, moisture may not melt if the temperature falls below 10 °C {50 °F}. Care needs...
... of fire, electric shock, personal injury, and material damage. ■ Camera Installation Location Install the camera on a boat, or other areas subject to strong vibration (This camera is not designed for use in the camera, Panasonic holds absolutely no responsibility for use in a vehicle.) • Near an... . ■ Noise interference considerations When using a power line that is greater than 1 meter, wiring should be performed again. If the camera is installed when humidity is very high, moisture may not melt if the temperature falls below 10 °C {50 °F}. Care needs...
WVCW964 User Guide
Page 12
... on the dome cover and block some of the picture. (The amount of snow that collects on the dome cover depends on image quality The camera does not have a wiper. ■ About effects on the quality and amount of the snow.) (3) Effects of dust and automobile exhaust Airborne dust and... automobile exhaust, from the location where the camera is installed, may be put together in the following conditions image quality may deteriorate or the image may be invisible. (1) In the rain The ...
... on the dome cover and block some of the picture. (The amount of snow that collects on the dome cover depends on image quality The camera does not have a wiper. ■ About effects on the quality and amount of the snow.) (3) Effects of dust and automobile exhaust Airborne dust and... automobile exhaust, from the location where the camera is installed, may be put together in the following conditions image quality may deteriorate or the image may be invisible. (1) In the rain The ...
WVCW964 User Guide
Page 13
...set now. 3. Use these switches to ON in the ceiling or on a wall. 1. DIP SWITCH SETTINGS In a configuration, the camera's RS485 data port is used . Remove the protective sticker from the top of the mounting brackets sold separately for installation for removing the...Switch 1: Terminator (Internal Termination Resistance) Set to select the communication protocol being used for camera control by the system controller, the camera's DIP switches must be set the DIP switches before installing the camera in the following : Communication parameters: Set with switch 2 Unit number: Set with ...
...set now. 3. Use these switches to ON in the ceiling or on a wall. 1. DIP SWITCH SETTINGS In a configuration, the camera's RS485 data port is used . Remove the protective sticker from the top of the mounting brackets sold separately for installation for removing the...Switch 1: Terminator (Internal Termination Resistance) Set to select the communication protocol being used for camera control by the system controller, the camera's DIP switches must be set the DIP switches before installing the camera in the following : Communication parameters: Set with switch 2 Unit number: Set with ...
WVCW964 User Guide
Page 15
...resets communication parameters to configure RS485 communication parameters as shown above. (2) Turn on power when this setting, see step 2 and page 21. * Turning on the camera. BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit BAUD RATE : 9 600 bit/s, DATA...DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit Perform the following steps to use this setting. (1) Turn off the camera, use DIP Switch 1 to their factory default settings. DIP Switch 1 ON 12345678 ON 12345678 ON 12345678 ON 12345678 Setting Description This setting resets communication ...
...resets communication parameters to configure RS485 communication parameters as shown above. (2) Turn on power when this setting, see step 2 and page 21. * Turning on the camera. BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit BAUD RATE : 9 600 bit/s, DATA...DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit Perform the following steps to use this setting. (1) Turn off the camera, use DIP Switch 1 to their factory default settings. DIP Switch 1 ON 12345678 ON 12345678 ON 12345678 ON 12345678 Setting Description This setting resets communication ...
WVCW964 User Guide
Page 16
...a mounting a bracket to which a safety wire can be attached. (3) Installation Surface x4 Caution: Consult an expert on the load bearing capacity of the camera mounted on the installation surface. 2. If it . * Special screw (mounting screw): Use a hexagon wrench for fixing on a ceiling with waterproof material.... Turn the upper base and separate it is not strong enough, the camera may fall down. wall nuts, anchor bolts, etc.) for the hexagon button screw (M6). x3 ● Construction 40 1-1/2B deep 30 ...
...a mounting a bracket to which a safety wire can be attached. (3) Installation Surface x4 Caution: Consult an expert on the load bearing capacity of the camera mounted on the installation surface. 2. If it . * Special screw (mounting screw): Use a hexagon wrench for fixing on a ceiling with waterproof material.... Turn the upper base and separate it is not strong enough, the camera may fall down. wall nuts, anchor bolts, etc.) for the hexagon button screw (M6). x3 ● Construction 40 1-1/2B deep 30 ...
WVCW964 User Guide
Page 17
... (3) mounting screws for details. Warning: Seal the cables with waterproof material such as silicon clay.See instructions of the upper base. • Turn the camera counter-clockwise to the end, viewed from the bottom. • Fasten 3 screws (the screws that "REAR" engraved on the upper base faces the... being exposed. (2) Be sure to the attachment pipe. • Fasten 4 screws (the screws that water or moisture cannot get inside the camera it could cause the dome to CONNECTIONS. Fall Prevention Wire Cables Upper Base (4) Fix the upper base to hook the fall prevention wire into ...
... (3) mounting screws for details. Warning: Seal the cables with waterproof material such as silicon clay.See instructions of the upper base. • Turn the camera counter-clockwise to the end, viewed from the bottom. • Fasten 3 screws (the screws that "REAR" engraved on the upper base faces the... being exposed. (2) Be sure to the attachment pipe. • Fasten 4 screws (the screws that water or moisture cannot get inside the camera it could cause the dome to CONNECTIONS. Fall Prevention Wire Cables Upper Base (4) Fix the upper base to hook the fall prevention wire into ...
WVCW964 User Guide
Page 18
...rear sun shield with this arrow Wire 5. Note: To remove the front/rear sunshields from being lost. Camera Safety wire Sun shield ■ Attach the front and rear sun shields (provided) to be mounted. Align... arrow (˚) until they click. Put the waterproof caps (provided) onto the tops of the camera to the camera. Before clamping the sun shield, close the front and rear sun shields (first latch the hook on... the rims and release the hooks from it. Caution: The camera safety wire is attached to one side to prevent them to the wire. -18- Do not ...
...rear sun shield with this arrow Wire 5. Note: To remove the front/rear sunshields from being lost. Camera Safety wire Sun shield ■ Attach the front and rear sun shields (provided) to be mounted. Align... arrow (˚) until they click. Put the waterproof caps (provided) onto the tops of the camera to the camera. Before clamping the sun shield, close the front and rear sun shields (first latch the hook on... the rims and release the hooks from it. Caution: The camera safety wire is attached to one side to prevent them to the wire. -18- Do not ...
WVCW964 User Guide
Page 19
...Doing so can cause pan, tilt, zoom, or focus to go out of position. • 24 V AC Power Supply Connection Recommended wire gauge sizes for camera 24 V AC RS485 Data Port Twisted Pair Cable*1 (RJ-12) Video Output Connector Coaxial Cable (5C-2V)*2 (BNC) Alarm Input Connector 8P Alarm Cable ...) (0.52mm2) (0.83mm2) Length (m) 20 of 5C-2V). *3: Be sure to connect the grounding cable to an external device, set up input. To VIDEO IN port (CAMERA IN) To sensor, etc. OFF : 4 V DC minimum 5 V DC maximum, or open ON : 1 V DC maximum or short Alarm Out : Open collector output. 16 V DC...
...Doing so can cause pan, tilt, zoom, or focus to go out of position. • 24 V AC Power Supply Connection Recommended wire gauge sizes for camera 24 V AC RS485 Data Port Twisted Pair Cable*1 (RJ-12) Video Output Connector Coaxial Cable (5C-2V)*2 (BNC) Alarm Input Connector 8P Alarm Cable ...) (0.52mm2) (0.83mm2) Length (m) 20 of 5C-2V). *3: Be sure to connect the grounding cable to an external device, set up input. To VIDEO IN port (CAMERA IN) To sensor, etc. OFF : 4 V DC minimum 5 V DC maximum, or open ON : 1 V DC maximum or short Alarm Out : Open collector output. 16 V DC...
WVCW964 User Guide
Page 20
.... . 33 mmmm{{00.1.1"}"} UUpp A Insert WWiriere IInnsseertrtththeewwireireunutniltAil Apopsoitisointion aannddcclalammppthtehecocnotanctatsc. After clamping the contacts, push them into the proper holes in the accessory connector of this camera until ascertaining that the unit is a one-time procedure. How to Assemble the Cable with the Accessory Connector Strip back the cable jacket approx. 3 mm...
.... . 33 mmmm{{00.1.1"}"} UUpp A Insert WWiriere IInnsseertrtththeewwireireunutniltAil Apopsoitisointion aannddcclalammppthtehecocnotanctatsc. After clamping the contacts, push them into the proper holes in the accessory connector of this camera until ascertaining that the unit is a one-time procedure. How to Assemble the Cable with the Accessory Connector Strip back the cable jacket approx. 3 mm...
WVCW964 User Guide
Page 21
...↔ 1000MS 9. AUTO1 : Sends alarm data each time an alarm signal is NOT USE. The delay time is the time is the time the camera should wait before sending a receive acknowledge (ACK). The delay time display changes in the sequence shown below. (unit: bits/s) The factory default setting ...data send mode setting. POLLING : Sends alarm data in the sequence shown below . (unit: ms) The factory default setting is the time that the camera should wait before resending data when no receive acknowledgement (ACK) is returned after data is sent. This is selected by DIP Switch 2. (page 13)...
...↔ 1000MS 9. AUTO1 : Sends alarm data each time an alarm signal is NOT USE. The delay time is the time is the time the camera should wait before sending a receive acknowledge (ACK). The delay time display changes in the sequence shown below. (unit: bits/s) The factory default setting ...data send mode setting. POLLING : Sends alarm data in the sequence shown below . (unit: ms) The factory default setting is the time that the camera should wait before resending data when no receive acknowledgement (ACK) is returned after data is sent. This is selected by DIP Switch 2. (page 13)...
WVCW964 User Guide
Page 22
... is a series of alphanumeric characters that it contains. ■ Displaying the Setup Menu ● When using the WV-CU650 (1) Select the camera (this camera), and the monitor where displays the setup menu. (2) Press the MENU button to display LCD MENU CAM 101. (3) Press the ENTER button or..., and then press the CAM (SET) button. To change . Select ON or OFF, and then press the CAM (SET) button. CAMERA ID--0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ SPACE ---- This will cause the selected character to the pages below for operating system controller WV-CU650. All setting configuration...
... is a series of alphanumeric characters that it contains. ■ Displaying the Setup Menu ● When using the WV-CU650 (1) Select the camera (this camera), and the monitor where displays the setup menu. (2) Press the MENU button to display LCD MENU CAM 101. (3) Press the ENTER button or..., and then press the CAM (SET) button. To change . Select ON or OFF, and then press the CAM (SET) button. CAMERA ID--0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ SPACE ---- This will cause the selected character to the pages below for operating system controller WV-CU650. All setting configuration...
WVCW964 User Guide
Page 23
...item to the image. ■ Preset Position Settings ● Position Number Selection (MAP) You could use the MAP item on the scene settings. INDOOR (L) INDOOR (H) OUTDOOR (L) OUTDOOR (H) AGC MID HIGH MID HIGH SENS UP OFF ×2 AUTO OFF ×2 AUTO SHUTTER OFF OFF AUTO AUTO INDOOR (L) INDOOR...the letter H next to the asterisk. • When the cursor is located at a position number that it already has a preset position assigned to specify the camera position (pan and tilt), the lens zoom setting, and the focus setting. 1. Display the setup menu (page 22), move the cursor to 33-64 in...
...item to the image. ■ Preset Position Settings ● Position Number Selection (MAP) You could use the MAP item on the scene settings. INDOOR (L) INDOOR (H) OUTDOOR (L) OUTDOOR (H) AGC MID HIGH MID HIGH SENS UP OFF ×2 AUTO OFF ×2 AUTO SHUTTER OFF OFF AUTO AUTO INDOOR (L) INDOOR...the letter H next to the asterisk. • When the cursor is located at a position number that it already has a preset position assigned to specify the camera position (pan and tilt), the lens zoom setting, and the focus setting. 1. Display the setup menu (page 22), move the cursor to 33-64 in...