Enc Manual
Page 2
...the location shown. IOS is a trademark of Bluetooth SIG, Inc. Note: The decals may not be shown at actual size. 305284 PROFORM and IFIT are trademarks of the warning decals. and other countries. The BLUETOOTH word mark and logos are used under license. If ... CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 6 PART IDENTIFICATION CHART 7 ASSEMBLY 8 HOW TO USE THE TREADMILL 16 FCC INFORMATION 24 HOW TO FOLD AND MOVE THE TREADMILL 25 MAINTENANCE AND TROUBLESHOOTING 26 EXERCISE GUIDELINES 29 PART LIST 30 EXPLODED DRAWING 32 ORDERING REPLACEMENT PARTS...
...the location shown. IOS is a trademark of Bluetooth SIG, Inc. Note: The decals may not be shown at actual size. 305284 PROFORM and IFIT are trademarks of the warning decals. and other countries. The BLUETOOTH word mark and logos are used under license. If ... CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 6 PART IDENTIFICATION CHART 7 ASSEMBLY 8 HOW TO USE THE TREADMILL 16 FCC INFORMATION 24 HOW TO FOLD AND MOVE THE TREADMILL 25 MAINTENANCE AND TROUBLESHOOTING 26 EXERCISE GUIDELINES 29 PART LIST 30 EXPLODED DRAWING 32 ORDERING REPLACEMENT PARTS...
Enc Manual
Page 4
... clothing away from the moving the treadmill, make sure that the storage latch is properly assembled. (See ASSEMBLY on page 8 and HOW TO FOLD AND MOVE THE TREADMILL on page 6 for the location of the treadmill will increase. 21. Do not operate the treadmill while it is walking on the treadmill, the noise level of the power...
... clothing away from the moving the treadmill, make sure that the storage latch is properly assembled. (See ASSEMBLY on page 8 and HOW TO FOLD AND MOVE THE TREADMILL on page 6 for the location of the treadmill will increase. 21. Do not operate the treadmill while it is walking on the treadmill, the noise level of the power...
Enc Manual
Page 7
...)-2 3/8" x 2 3/8" Screw (7)-4 5/16" x 3" Screw (28)-4 1/4" x 4 1/2" Screw (8)-2 7 The number in the hardware kit, check to identify small parts used for assembly. PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity used for assembly. The number following the key number is the key number of the part, from the PART LIST near...
...)-2 3/8" x 2 3/8" Screw (7)-4 5/16" x 3" Screw (28)-4 1/4" x 4 1/2" Screw (8)-2 7 The number in the hardware kit, check to identify small parts used for assembly. PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity used for assembly. The number following the key number is the key number of the part, from the PART LIST near...
Enc Manual
Page 8
...register your warranty • ensures priority customer support if assistance is normal. ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner... parts, see page 7. • Assembly requires the following tools: the included hex keys one Phillips screwdriver one adjustable wrench To avoid damaging parts, do not have internet access, call Customer Service (see the front cover of the treadmill. This is ever needed Note: ...
...register your warranty • ensures priority customer support if assistance is normal. ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner... parts, see page 7. • Assembly requires the following tools: the included hex keys one Phillips screwdriver one adjustable wrench To avoid damaging parts, do not have internet access, call Customer Service (see the front cover of the treadmill. This is ever needed Note: ...
Enc Manual
Page 12
start all four Screws, and then tighten them. 8 9 5 84 31 9 5 84 9. With the help of a second person, hold the console assembly (G) near the Handrail (84). Connect the ground wire (H) from the Upright Wire. 9 G 81 84 I 31 A H 58 I ). The connectors should slide together ...easily and snap into place. Then, remove the wire tie (A) from the console assembly (G) to the Console Ground Wire (58) on the Pulse Crossbar (31). See the inset drawing. 8. IMPORTANT: To avoid damaging the Pulse Crossbar (31), do...
start all four Screws, and then tighten them. 8 9 5 84 31 9 5 84 9. With the help of a second person, hold the console assembly (G) near the Handrail (84). Connect the ground wire (H) from the Upright Wire. 9 G 81 84 I 31 A H 58 I ). The connectors should slide together ...easily and snap into place. Then, remove the wire tie (A) from the console assembly (G) to the Console Ground Wire (58) on the Pulse Crossbar (31). See the inset drawing. 8. IMPORTANT: To avoid damaging the Pulse Crossbar (31), do...
Enc Manual
Page 13
start 11 all six Screws, and then tighten them. Firmly tighten the four 1/4" x 1/2" Screws (4). 4 31 4 1 1 13 10. Set the console assembly (G) on the Handrails (84). Attach the Pulse Crossbar (31) to the console assembly (G) with four 1/4" x 1/2" Screws (4); do not tighten the Screws yet. 84 84 81 4 4 90 11. Make sure that no wires are pinched. 10 G Insert the excess Upright Wire (81) into the Right Upright (90). Attach the console assembly (G) with six #8 x 5/8" Screws (1); Do not G overtighten the Screws.
start 11 all six Screws, and then tighten them. Firmly tighten the four 1/4" x 1/2" Screws (4). 4 31 4 1 1 13 10. Set the console assembly (G) on the Handrails (84). Attach the Pulse Crossbar (31) to the console assembly (G) with four 1/4" x 1/2" Screws (4); do not tighten the Screws yet. 84 84 81 4 4 90 11. Make sure that no wires are pinched. 10 G Insert the excess Upright Wire (81) into the Right Upright (90). Attach the console assembly (G) with six #8 x 5/8" Screws (1); Do not G overtighten the Screws.
Enc Manual
Page 15
... of direct sunlight. the hex key is designed for use the treadmill. IMPORTANT: The Tablet Holder (27) is used to the console, keep the treadmill out of plastic on the Tablet Holder (27) into the slots (J) in the console assembly (G). Attach the Tablet Holder (27) with most full-size tablets.... To protect the floor or carpet, place a mat under the treadmill. Do not place any other electronic device or object in a secure place; Note: ...
... of direct sunlight. the hex key is designed for use the treadmill. IMPORTANT: The Tablet Holder (27) is used to the console, keep the treadmill out of plastic on the Tablet Holder (27) into the slots (J) in the console assembly (G). Attach the Tablet Holder (27) with most full-size tablets.... To protect the floor or carpet, place a mat under the treadmill. Do not place any other electronic device or object in a secure place; Note: ...