Pyle PLMRA410BT Support and Manuals
Get Help and Manuals for this Pyle item
View All Support Options Below
Free Pyle PLMRA410BT manuals!
Problems with Pyle PLMRA410BT?
Ask a Question
Free Pyle PLMRA410BT manuals!
Problems with Pyle PLMRA410BT?
Ask a Question
Most Recent Pyle PLMRA410BT Questions
Popular Pyle PLMRA410BT Manual Pages
User Guide - Page 1
... unit during lightning storms or when it is corrosive and prolonged exposure will handle the necessary paperwork and repair.
Be aware that any cables, wired or power cord from an authorized Pyle Audio service center. Elite Series Waterproof Amplifiers If the unit is likely to undergo excess vibration through use protective plastic cups or...
User Guide - Page 2
...amplifier. NOTE: CARE MUST BE TAKEN AGAINST BATTERY OVER-DISCHARGE CAUSED BY LONG OPERATION Of THE SET AT A HIGH SOUND LEVEL WHEN THE ENGINE IS NOT RUNNING OR IDLING. Maintenance
Keep the...electronic devices and distort or melt plastic parts.
If there are any farther than you may adjust the gain control to keep it dry immediately. Elite Series Waterproof Amplifiers Keep the amplifier away...
User Guide - Page 4
... both this amplifier and the automobile electrical system from wrong electrical conditions.
www.PyleAudio.com
Elite Series Waterproof Amplifiers The Pyle Elite Series Amps feature options and configurations that will light up
indicating power conditions are silver-plated for detailed specifications and more information. Connect+ 12V DC power supply wire Into the terminal from the...
User Guide - Page 5
Mono Input Connection RCA Type Terminals Bridge-Ability *Not available on all PLMRA amp models. Couple the RCA input with line level output.
RCA Type The Elite Series Amps feature plated RCA terminals for detailed model information, specific model wiring and connection ability. Stereo Input Connection RCA Type Terminals High Impedance Low Level Inputs
Visit www.PyleAudio.com...
User Guide - Page 6
... channel amplifier. The ideal speaker impedance for each bridged channel. Operation of the amplifier below shows a pair of speakers connected in normal operation.
Mono Amp System Select Elite Series Amps may easily be bridgeable from a 2 channel amplifier to the corresponding LEFT and RIGHT Speakers. (Fig. 1 below this is 4 ohms. The amplifier will void...
User Guide - Page 7
...of burning out their amplifiers.
Some users may automatically set the gain to help match the signals correctly. Avoid problems and match your vehicle's external switch for detailed model information and connection ability. typically blue in the bridged mode. Models: PLMRA210BT, PLMRA410BT, PLMRA430BT, PLMRA630BT, PLMRA830BT
Elite Series Waterproof Amplifiers Your system can also become...
User Guide - Page 8
Wiring
Stereo Amp Connection Mono Amp Connection
Elite Series Waterproof Amplifiers PLMRA210BT -
User Guide - Page 9
PLMRA410BT - Speaker Level (BTL or Common Ground) Four Speaker Output Mode Floating Ground Type Elite Series Waterproof Amplifiers Wiring
Stereo Input Connection RCA Input
High Level -
User Guide - Page 10
... Amplifiers
If you must switch OFF the whole system immediately double check speaker wire connections and isolation before switching on the amplifier again.
PLMRA410BT - Note: Elite Series Ampshave built-in short circuit protection. In case of this, you mistakingly connect any speaker wires to ground, or positive power ( +) and (-) Wires short ...
User Guide - Page 11
...positive 12V ON/OFF. Connect the 'Remote' pole to the corresponding speakers. Elite Series Waterproof Amplifiers Connect the GND pole of handling high power.
The speakers...receiver power antenna lead. To make a good grounding and prevent motor boating noise problem connect another 12 gauge minimum wire from the (-) negative battery terminal to chassis... from battery). 2. PLMRA410BT -
User Guide - Page 13
Elite Series Waterproof Amplifiers PLMRA430BT - Wiring
4 Channel Input Connection Low Level Inputs
2 Channel Input Connection Low Level Inputs
High Level Wiring
4 Channel Connection Floating Ground
Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability.
User Guide - Page 22
...choose a mounting location which may be fastened.
Elite Series Waterproof Amplifiers Once successfully paired with your device. Tighten...amp network name will appear as to not interfere with any wires, lines or other electrical systems. Then, drill the pilot holes in the mounting surface for the mounting screws. The amp will not require a password to install it. Your amp...
User Guide - Page 23
...problem. • If the shutdown was a result of a thermal overload condition, allow the amplifier to replace the fuse, or feel your system has become faulty, please contact Pyle technical support...please take precaution and have a professional, or install under the supervision of a trained professional. ...Elite Series Waterproof Amplifiers or speaker short circuit, be illuminated. Mounting...
User Guide - Page 24
...service. Confirm that isn't covered in the audio. Elite Series Waterproof Amplifiers To check if the amp... is in fuses. Only one channel works. Noise in the manufacturer's warranty.
Readjust the Input Level Control(s) to chassis ground. Check both In-line and built-in need to replace... the problem is set to the...
User Guide - Page 25
Models & Specs Elite Series Waterproof Amplifiers Pyle Elite Series -
Pyle PLMRA410BT Reviews
We have not received any reviews for Pyle yet.