Samsung STP-103G - STP 103S B/W Direct Thermal Printer Support and Manuals
Get Help and Manuals for this Samsung item
View All Support Options Below
Free Samsung STP-103G manuals!
Problems with Samsung STP-103G?
Ask a Question
Free Samsung STP-103G manuals!
Problems with Samsung STP-103G?
Ask a Question
Most Recent Samsung STP-103G Questions
Is This Printer Discontinued?
Is above printer discontinued? Bixolon STP-103II
Is above printer discontinued? Bixolon STP-103II
(Posted by kanti 8 years ago)
How To Solve Red Led Is Continues Blinking On Samsung Ml-1610 Printer
(Posted by geeyes77 9 years ago)
Popular Samsung STP-103G Manual Pages
User Manual - Page 1
USER'S MANUAL
STP-103
THERMAL PRINTER
KN04-00003A Rev. 2.6
POWER ERROR
FEED
ON LINE
www.samsungminiprinters.com
User Manual - Page 2
...
PROHIBITED
Do not pull the cable to repair it before calling your dealer.
Switch off and unplug the printer before taking following measures.
and you need these services.
Do not use only the supplied adapter. If this happened, switch off the printer and unplug the set from the printer, unplug it .
origin of a fire or a breakdown...
User Manual - Page 3
...
The STP-103 and STP-103P Roll Printer are designed to correct the interference at his own expense.
This equipment generates, uses, and can be required to provide reasonable protection against harmful interference when the equipment is connected. - These limits are designed for a Class A digital device, pursuant to read the instruction in a particular installation. Low noise thermal...
User Manual - Page 4
... in direct sunlight or excessive heat. Make sure that there is enough space around the printer so that it can be used easily.
7 Operating Control Panel 9
Chapter 2. Functions 27
Chapter 9. Installing the Paper Roll 13
Chapter 4. Specification 52
※Option : STP-103DK 53
6
Chapter 1. Checking the contents of Contents
Chapter 1. Setting the DIP Switching 14
Chapter 5. Code...
User Manual - Page 5
... lights provide information on printer conditions.
1-3.
Printer Part Names
(10)
(1) Cover top (2) Case top (3) Case bottom (4) Control panel (5) Roller (6) Power switch (7) Interface connector (male) (8) DC Jack (9) Interface connector (female) (11) (10) Roll paper (11) Detector switch
(5) (1)
Rear View
(2) (4)
Rear View
(6)
(7)
(8)
STP-103S
Control Panel
POWER ERROR
FEED ON LINE...
User Manual - Page 6
otherwise you disconnect the DC cable connector.
10
11 STP-103S / STP-103P
2-2. Connecting the printer to your Computer
STP-103S You need an appropriate serial interface cable to connect your computer to make sure that the main unit's power cord is not plugged into the printer's interface connector. 2. Tighten the screws on the power supply to the...
User Manual - Page 9
... is off. The self-test prints the current printer settings, which provide the following information :
-
This can be useful in a two-column format. Then the printer enters the hexadecimal dump mode.
4. Turn on the hexadecimal dump function, the printer prints all the codes it receives in finding software problems. When you turn off .
16
17 Running...
User Manual - Page 16
...the selected printer status specified by paper roll sensor
7
Off
00
0
Not used . n=2 : Transmit off . n=3 : Transmit error status. ...Sets the character spacing for the right side of the character to the following parameters:
n=1 : Transmit printer status. n specifies the
requests as LF; n=4 : transmit paper roll sensor status. On,On 0C
12 Paper roll near -end sensor is ignored. Paper...
User Manual - Page 18
...
ASCII ESC ?
Undefined. Undefined. ESC ?
ESC J n [Name] [Format]
[Range] [Description]
Print and feed paper
ASCII ESC J n
Hex
1B 4A n
Decimal 27 74 n
0 ≤n ≤255
Prints the data in the print buffer and resets the printer mode to be set. ESC 2 [Name] [Format]
[Description]
Select 1/6-inch line spacing
ASCII
ESC 2
Hex
1B 32...
User Manual - Page 20
... printer feeds the
label paper to the next print starting position to the beginning
of the line.
● This command does cot affect the line spacing set by ESC 2 or
ESC 3.
● The maximum paper feed amount is turned on. ESC t n [Name] [Format]
[Range] [Description]
Select character code table. FS q n [xL xH yH d1 ...dk...
User Manual - Page 22
... continuously at the interval specified by nL and nH.
● The printing area width is set to [(nL + nH X 256) X (horizontal motion
unit6)] inches. n selects the printing position as follows:
n
Printer ID
Specification
ID(hexadecimal)
1,49 Printer model ID STP-103S / STP-103P
30
2,50
Type ID
02
3,51 ROM version ID Depends on ROM version
10
GS...
User Manual - Page 24
...
72 CODE93 73 CODE128
Number of the HRI character string. ● The printer prints HRI characters (■ + an alphabetic character) as a control character...Name] [Format]
[Range] [Description]
[Default]
Set bar code height
ASCII
GS h
n
Hex
1D
68
n
Decimal
29
104
n
1 ≤n ≤255
Sets the height of dots in the vertical direction.
ASCII
GS f
n
Hex
1D 66 n
...
User Manual - Page 25
... to Appendix J for the information of the CODE128 bar code and its code table. ● When using the CODE128 in this example, the printer first prints "No."
In code set B. using CODE B, then prints the following data as a character for code set C : 2-digit numeral characters using CODE C. Be sure to code set A, B, or C. * Function character (FNC1, FNC2, FNC3, FNC4) The usage...
User Manual - Page 26
...Set the horizontal size of data bits (yL+yH×256)in the horizontal direction for the bit image.
• yL, yH, selects the number of the bar code. n specifies the bar code width as follows: CODE39, ITF, CODABAR
[Default]
n = 3
50
APPENDIX A : CONNECTORS
Serial Interface Connector (STP-103S)
PRINTER...
BUSY (I)
12
PE (I)
13
SLCT
15
/ERROR (I)
16
/INIT (O)
18~25
GND
FGND
25...
User Manual - Page 27
...(0.47") 2) Outside : Ø18mm (0.71")
※Option : STP-103DK
1) Serial Interface Connector Specification
PRINTER
19
RXD (I)
20
TXD (O)
18
RTS (O)
21
CTS (I)
FGND
... - APPENDIX B : Specification
Printing method Dot density Printing width Paper width Characters per line
Printing Speed
Receive buffer size Supply voltage
Environmental conditions
MCBF
Thermal line printing
200 x 200...
Samsung STP-103G Reviews
We have not received any reviews for Samsung yet.