Sanyo PLC-XTC50AL Support and Manuals
Get Help and Manuals for this Sanyo item
View All Support Options Below
Free Sanyo PLC-XTC50AL manuals!
Problems with Sanyo PLC-XTC50AL?
Ask a Question
Free Sanyo PLC-XTC50AL manuals!
Problems with Sanyo PLC-XTC50AL?
Ask a Question
Popular Sanyo PLC-XTC50AL Manual Pages
Owners Manual - Page 1
Owner's Manual
Multimedia Projector
MODEL PLC-XTC50AL
*Projection lens is optional.
Owners Manual - Page 4
..., ANSI/NFPA 75. NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. Please, help us to countries in a proper position. If the projector is critical for a long time, the cooling fans can also be indicated as possible,
otherwise eye damage could result. To the Owner
Before installing and operating the projector, read this manual again, check operations and cable...
Owners Manual - Page 9
...in a particular installation. red or ... of this projector meets the ...Parts Department indicated in your electrician. The Wires in this mains lead are coloured in accordance with the following code...instructions, may not correspond with the coloured markings identifying the terminals in your socket outlet, it .
Model Number(s) : PLC-XTC50AL Trade Name : Sanyo Responsible party : SANYO...
Owners Manual - Page 50
...can be displayed the next time you turn on the projector.
After capturing the projected image, go to the Logo select function and set to "4321" at the factory. Capture
Select [Yes]... capture a new image, the previously stored image is automatically reset and the projector captures an image without a Logo PIN code. To cancel the Capture function, select [No].
On The screen logo cannot...
Owners Manual - Page 64
... be switched manually.
Lamp control Lamp status
LAMP 1/2 REPLACE indicators
Lamp 1/2 Replace Indicators
The LAMP 1/2 REPLACE indicators light yellow when the total lighting time of a Projection Lamp reaches the recommended total hours of lamps and shows the status on screen or on Lamp
(LAMP 1/2 REPLACE indicator flashes yellow.) Projection lamp is out, the projector operates with number...
Owners Manual - Page 65
... a projector which has been installed on the ceiling, you should always assume that secures the lamp cover with a coin, and then open the Lamp cover. Lamp 1
5 Replace the lamp with a lamp of the lamp cover, not underneath it. CAUTION
Allow a projector to "Off" (p.55), or during "Freeze" (p.30). The glass can shatter and may fall out when the lamp cover is set...
Owners Manual - Page 66
... plug from the cooling air circulation holes. Any broken shards found should be ordered through your projector : PLC-XTC50AL ● Replacement Lamp Type No. : POA-LMP125 (Service Parts No. 610 342 2626)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which the projector and lamp are not appropriately trained to do so, may result in an accident or injury caused by...
RS232 Basic - Page 9
PLC-XTC50AL Basic Serial Command Functional Specifications
6.
Functional Execution Command 6.1 Format
PC issues a command in sequence within 120 ms, the function is executed for 120 ms from the moment. 3) When receiving the same command in the following format: "C" Command [CR]
Command: two characters (See Functional Execution Command Table)
Projector decodes the received data and returns...
RS232 Basic - Page 10
... to Lamp Failure
NONE (No Execution) NONE (No Execution) C00: POWER ON C01: POWER OFF
NONE (No Execution)
Note) in process Cooling Down due to Abnormal Temperature Abnormal Temperature Status
When ZOOM+/-, FOCUS +/-, LENS SHIFTUP/ DOWN/LEFT/RIGHT are limited. PLC-XTC50AL Basic Serial Command Functional Specifications
6.4 Operation Requirements
In the following status of projector...
RS232 Expand - Page 1
EXPAND SERIAL COMMAND FUNCTIONAL SPECIFICATIONS
PLC-XTC50AL
SANYO Electric Co., Ltd DS Company
Projector Division
RS232 Expand - Page 8
...9Pin)
8/76 Supporting Firmware Ver. 1.x of the projector. Therefore commands in Service mode.
2.2 Connection
Dedicated serial cables must be used to control a projector remotely from a computer with RS-232C. Commands in this document are used for PLC-XTC50AL.
PLC-XTC50AL Expand Serial Command Functional Specifications
1 Overview
This Functional Specification defines communication...
RS232 Expand - Page 17
...projector decodes the received command and when it is as below. PLC-XTC50AL Expand Serial Command Functional Specifications
8 Functional Execution Command 8.1 Format
1) PC issues commands in the above status, it returns error code... When the received data cannot be decoded, the projector returns"?" [CR]
8.2 Transfer Example
When setting projector's total dots to 1344 by Expand Serial command
PC...
RS232 Expand - Page 19
...the value returns to the original setting. (It is stored in the projector's memory. RED
%1
"G" --------- PLC-XTC50AL Expand Serial Command Functional Specifications
8.4.5 CF_SHARP Command
Command "CF_SHARP_%1" [CR]
"000-015 Directly specify setting value of Sharpness
%1
"UP Increment setting value of Sharpness by 1
"DN Decrement setting value of Sharpness by 1
Details Response...
RS232 Expand - Page 20
... to L2 (for still image).
PLC-XTC50AL Expand Serial Command Functional Specifications
8.4.8 CF_COLTEMP Command
Command "CF_COLTEMP_%1" [CR]
"000 Xlow
%1
"001 Low "002 Mid
"003 High
Details Response
Set Color Temperature (Available only in the normal Power ON status) The value set by this command will not be stored in the projector's memory. Therefore, when the power...
RS232 Expand - Page 71
...
"OFF PIN code lock OFF is entered. PLC-XTC50AL Expand Serial Command Functional Specifications
9.11.19 CR_SECURITY Command
Command "CR_ SECURITY" [CR]
Details
Get ON/OFF setting status of PIN code lock on menu
Acceptable "000_%1" [CR]
Response
"ON1 PIN code lock ON 1 is set on the menu
%1
"ON2 PIN code lock ON 2 is set on the menu
Unacceptable "Error Code" [CR...
Sanyo PLC-XTC50AL Reviews
We have not received any reviews for Sanyo yet.