MX-2600N | MX-3100N Operation Manual
Page 1
OPERATION GUIDE Search based on what you want to do MAKE A COPY PRINT A DOCUMENT SEND A FAX SCAN AN IMAGE / SEND AN INTERNET FAX SAVE A JOB AND REUSE IT LATER MAINTAIN THE MACHINE Search using the table of contents BEFORE USING THE MACHINE COPIER PRINTER FACSIMILE SCANNER / INTERNET FAX DOCUMENT FILING SYSTEM SETTINGS TROUBLESHOOTING About Operation Guide
OPERATION GUIDE Search based on what you want to do MAKE A COPY PRINT A DOCUMENT SEND A FAX SCAN AN IMAGE / SEND AN INTERNET FAX SAVE A JOB AND REUSE IT LATER MAINTAIN THE MACHINE Search using the table of contents BEFORE USING THE MACHINE COPIER PRINTER FACSIMILE SCANNER / INTERNET FAX DOCUMENT FILING SYSTEM SETTINGS TROUBLESHOOTING About Operation Guide
MX-2600N | MX-3100N Operation Manual
Page 40
... the manuals is explained in "Downloading the Operation Guide" in each of the procedures for using the print function. 4. The procedure for using the machine. TROUBLESHOOTING This chapter explains how to remove paper misfeeds and provides answers to load paper, and machine maintenance. 2.
... the manuals is explained in "Downloading the Operation Guide" in each of the procedures for using the print function. 4. The procedure for using the machine. TROUBLESHOOTING This chapter explains how to remove paper misfeeds and provides answers to load paper, and machine maintenance. 2.
MX-2600N | MX-3100N Operation Manual
Page 755
... after it has been enabled. ">" indicates the setting sequence and indicates the state of system settings similar to your dealer or nearest SHARP Service Department. REMOVING MISFEEDS • REMOVING MISFEEDS 8-2 • PAPER MISFEED ILLUSTRATIONS 8-3 REMOVING STAPLE JAMS • FINISHER 8-7 •..."Other Settings" > "Rotation Copy Setting" > This is an abbreviated description of the procedure for selecting the setting. CHAPTER 8 TROUBLESHOOTING This chapter provides solutions to help you are unable to solve a problem using this manual. If you configure the settings.
... after it has been enabled. ">" indicates the setting sequence and indicates the state of system settings similar to your dealer or nearest SHARP Service Department. REMOVING MISFEEDS • REMOVING MISFEEDS 8-2 • PAPER MISFEED ILLUSTRATIONS 8-3 REMOVING STAPLE JAMS • FINISHER 8-7 •..."Other Settings" > "Rotation Copy Setting" > This is an abbreviated description of the procedure for selecting the setting. CHAPTER 8 TROUBLESHOOTING This chapter provides solutions to help you are unable to solve a problem using this manual. If you configure the settings.
MX-2600N | MX-3100N Operation Manual
Page 756
TROUBLESHOOTING REMOVING MISFEEDS This section explains what to do not touch or damage the transfer belt. • Carefully pull the paper out without tearing it. • A ...
TROUBLESHOOTING REMOVING MISFEEDS This section explains what to do not touch or damage the transfer belt. • Carefully pull the paper out without tearing it. • A ...
MX-2600N | MX-3100N Operation Manual
Page 757
Refer to the illustration below . Open the automatic document feeder. Rotate the transfer roller in the output area Remove the misfed paper. TROUBLESHOOTING PAPER MISFEED ILLUSTRATIONS If you require more information when reading the instructions in the touch panel, see the paper misfeed illustrations below and then go ...
Refer to the illustration below . Open the automatic document feeder. Rotate the transfer roller in the output area Remove the misfed paper. TROUBLESHOOTING PAPER MISFEED ILLUSTRATIONS If you require more information when reading the instructions in the touch panel, see the paper misfeed illustrations below and then go ...
MX-2600N | MX-3100N Operation Manual
Page 758
... misfed paper. (9) Paper misfeed in tray 1 to tray 4 (side) 8-4 Contents Take care not to tray 4 (side) The misfeed may tear misfed paper and make it . TROUBLESHOOTING (3) Paper misfeed in the fusing unit Rotate knob and remove the misfed paper. (6) Paper misfeed in the tray) Before pulling the tray out, open the...
... misfed paper. (9) Paper misfeed in tray 1 to tray 4 (side) 8-4 Contents Take care not to tray 4 (side) The misfeed may tear misfed paper and make it . TROUBLESHOOTING (3) Paper misfeed in the fusing unit Rotate knob and remove the misfed paper. (6) Paper misfeed in the tray) Before pulling the tray out, open the...
MX-2600N | MX-3100N Operation Manual
Page 759
.... Turn the roller knob as shown in the finisher Open the front cover. (10) Paper misfeed in the illustration. Make sure that there is installed. TROUBLESHOOTING (11) Paper misfeed in the machine.
.... Turn the roller knob as shown in the finisher Open the front cover. (10) Paper misfeed in the illustration. Make sure that there is installed. TROUBLESHOOTING (11) Paper misfeed in the machine.
MX-2600N | MX-3100N Operation Manual
Page 760
... large capacity tray away from the main unit until it stops. Move lever (A) to the right and remove the misfed paper. (B) Remove the misfed paper. TROUBLESHOOTING (14) Paper misfeed in the paper pass unit Pull out the paper pass unit and remove the misfed paper. Move lever (B) to the right (A) and...
... large capacity tray away from the main unit until it stops. Move lever (A) to the right and remove the misfed paper. (B) Remove the misfed paper. TROUBLESHOOTING (14) Paper misfeed in the paper pass unit Pull out the paper pass unit and remove the misfed paper. Move lever (B) to the right (A) and...
MX-2600N | MX-3100N Operation Manual
Page 761
... occur again. Remove the leading staple if it stops. Raise the lever at the front end of the staple case and remove the jammed staple. TROUBLESHOOTING REMOVING STAPLE JAMS Follow the steps below to remove a staple jam. ☞ FINISHER ☞ SADDLE STITCH FINISHER (page 8-9) FINISHER Open the cover. 1 While pressing the...
... occur again. Remove the leading staple if it stops. Raise the lever at the front end of the staple case and remove the jammed staple. TROUBLESHOOTING REMOVING STAPLE JAMS Follow the steps below to remove a staple jam. ☞ FINISHER ☞ SADDLE STITCH FINISHER (page 8-9) FINISHER Open the cover. 1 While pressing the...
MX-2600N | MX-3100N Operation Manual
Page 762
Gently slide the finisher back to the right. TROUBLESHOOTING Lower the lever at the front end of the staple case. 5 Replace the staple case. Push the staple case in until it clicks into place. 6 Slide the finisher back to the right until it locks into its original position. 7 Close the cover. 8 8-8 Contents
Gently slide the finisher back to the right. TROUBLESHOOTING Lower the lever at the front end of the staple case. 5 Replace the staple case. Push the staple case in until it clicks into place. 6 Slide the finisher back to the right until it locks into its original position. 7 Close the cover. 8 8-8 Contents
MX-2600N | MX-3100N Operation Manual
Page 763
Remove the leading staple if it stops. 2 Lower the staple case release lever and remove the staple case. 3 Pull the staple case out to the left until it is bent. If bent staples remain, a 4 staple jam will occur again. Raise the lever at the front end of the staple case and remove the jammed staple. Lower the lever at the front end of the staple case. 5 8-9 Contents Take care that a bent staple does not hurt you. SADDLE STITCH FINISHER Finisher unit TROUBLESHOOTING Open the front cover. 1 While pulling the lever, slide the saddle stitch finisher to the right.
Remove the leading staple if it stops. 2 Lower the staple case release lever and remove the staple case. 3 Pull the staple case out to the left until it is bent. If bent staples remain, a 4 staple jam will occur again. Raise the lever at the front end of the staple case and remove the jammed staple. Lower the lever at the front end of the staple case. 5 8-9 Contents Take care that a bent staple does not hurt you. SADDLE STITCH FINISHER Finisher unit TROUBLESHOOTING Open the front cover. 1 While pulling the lever, slide the saddle stitch finisher to the right.
MX-2600N | MX-3100N Operation Manual
Page 764
Push the staple case in until it clicks into place. 6 Push the saddle stitch finisher back and latch it to the machine. 7 Close the front cover. 8 Make a test print or copy in staple sort mode to verify that stapling takes place correctly. 8-10 Contents TROUBLESHOOTING Replace the staple case.
Push the staple case in until it clicks into place. 6 Push the saddle stitch finisher back and latch it to the machine. 7 Close the front cover. 8 Make a test print or copy in staple sort mode to verify that stapling takes place correctly. 8-10 Contents TROUBLESHOOTING Replace the staple case.
MX-2600N | MX-3100N Operation Manual
Page 765
Do not replace removed output in the output tray. Open the side cover. 1 Remove the staple cartridge from the output tray of the saddle stitch finisher. TROUBLESHOOTING Saddle stitch unit Before starting this procedure, remove all output from the staple unit. 2 Lock the staple unit. Push the staple unit up until you . 8-11 Contents Remove the jammed staples. 5 Take care that a bent staple does not hurt you hear a click. 3 4 (A) (B) Press (A) down and pull up knob (B).
Do not replace removed output in the output tray. Open the side cover. 1 Remove the staple cartridge from the output tray of the saddle stitch finisher. TROUBLESHOOTING Saddle stitch unit Before starting this procedure, remove all output from the staple unit. 2 Lock the staple unit. Push the staple unit up until you . 8-11 Contents Remove the jammed staples. 5 Take care that a bent staple does not hurt you hear a click. 3 4 (A) (B) Press (A) down and pull up knob (B).
MX-2600N | MX-3100N Operation Manual
Page 766
Remove the cover from each staple cartridge and then install the cartridge. 7 Close the side cover. 8 Make a test print or copy using the saddle stitch function to verify that stapling takes place correctly. 8-12 Contents TROUBLESHOOTING Push down knob (B). 6 (B) Load new staple cartridges.
Remove the cover from each staple cartridge and then install the cartridge. 7 Close the side cover. 8 Make a test print or copy using the saddle stitch function to verify that stapling takes place correctly. 8-12 Contents TROUBLESHOOTING Push down knob (B). 6 (B) Load new staple cartridges.
MX-2600N | MX-3100N Operation Manual
Page 767
... and white or color when the [COLOR START] key is lit or blinking, do not switch off the [POWER] key ( ) and the main power switch. TROUBLESHOOTING COPYING PROBLEMS RELATED TO COPYING OPERATION • Copying does not take place 8-13 • Auto selection of the color mode does not take place 8-13...
... and white or color when the [COLOR START] key is lit or blinking, do not switch off the [POWER] key ( ) and the main power switch. TROUBLESHOOTING COPYING PROBLEMS RELATED TO COPYING OPERATION • Copying does not take place 8-13 • Auto selection of the color mode does not take place 8-13...
MX-2600N | MX-3100N Operation Manual
Page 768
... in the touch panel. If you using automatic paper selection and automatic ratio selection. When user authentication is selected, a message will appear in your administrator. TROUBLESHOOTING Problem Image rotation does not take place. Does the paper type setting of the selected tray specify a type of a tray cannot be combined with your...
... in the touch panel. If you using automatic paper selection and automatic ratio selection. When user authentication is selected, a message will appear in your administrator. TROUBLESHOOTING Problem Image rotation does not take place. Does the paper type setting of the selected tray specify a type of a tray cannot be combined with your...
MX-2600N | MX-3100N Operation Manual
Page 769
TROUBLESHOOTING PROBLEMS RELATED TO COPY RESULTS Problem The image is best for copying the light color shading and fine text found on . • Printed Photo This ...
TROUBLESHOOTING PROBLEMS RELATED TO COPY RESULTS Problem The image is best for copying the light color shading and fine text found on . • Printed Photo This ...
MX-2600N | MX-3100N Operation Manual
Page 770
..., finisher, or other peripheral device installed on your computer and the machine. BEFORE USING THE MACHINE "SIDE AND BACK" (page 1-7) The machine must be lost. TROUBLESHOOTING PRINTING PROBLEMS RELATED TO PRINTING OPERATION • Printing does not take place 8-16 • Color printing does not take place 8-18 • Two-sided printing...
..., finisher, or other peripheral device installed on your computer and the machine. BEFORE USING THE MACHINE "SIDE AND BACK" (page 1-7) The machine must be lost. TROUBLESHOOTING PRINTING PROBLEMS RELATED TO PRINTING OPERATION • Printing does not take place 8-16 • Color printing does not take place 8-18 • Two-sided printing...
MX-2600N | MX-3100N Operation Manual
Page 771
... possible if the IP address changes. If a device is not powered on or is , it may not be possible to correct the problem. 8-17 Contents TROUBLESHOOTING Problem Printing does not take place. If the IP address has changed, change the port setting in Windows is used and the [SNMP Status Enabled...
... possible if the IP address changes. If a device is not powered on or is , it may not be possible to correct the problem. 8-17 Contents TROUBLESHOOTING Problem Printing does not take place. If the IP address has changed, change the port setting in Windows is used and the [SNMP Status Enabled...
MX-2600N | MX-3100N Operation Manual
Page 772
TROUBLESHOOTING Problem Printing does not take appropriate action. Have functions been disabled by the administrator? In Windows, [Black and White Print] can use may be used ...
TROUBLESHOOTING Problem Printing does not take appropriate action. Have functions been disabled by the administrator? In Windows, [Black and White Print] can use may be used ...