Service Manual
Page 3
... the magnetron or other damage), (4) damage to or loosening of hinges and latches, (5) evidence of the specified limit, contact SHARP ELECTRONICS CORPORATION immediately @1-800-237-4277. The owner of any service test or inspection within the microwave generating compartments, check the magnetron... adjusted by procedures described in this service manual. Service personnel should inform SHARP ELECTRONICS CORPORATION of the unit should be performed on each oven prior to release to the owner. R-231NW RP2R30EKWCAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID EXPOSURE TO EXCESSIVE...
... the magnetron or other damage), (4) damage to or loosening of hinges and latches, (5) evidence of the specified limit, contact SHARP ELECTRONICS CORPORATION immediately @1-800-237-4277. The owner of any service test or inspection within the microwave generating compartments, check the magnetron... adjusted by procedures described in this service manual. Service personnel should inform SHARP ELECTRONICS CORPORATION of the unit should be performed on each oven prior to release to the owner. R-231NW RP2R30EKWCAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID EXPOSURE TO EXCESSIVE...
Service Manual
Page 6
... are used at voltages more than 250V. All the parts marked "*" on parts list are damaged, loosened or removed. 3 - 1 R-231NW CHAPTER 3. It is not any other visible damage with Operation and Service Information for the SHARP MICROWAVE OVENS, R-230KK and R-230KW. Servicing and repair work must be qualified to provide...
... are used at voltages more than 250V. All the parts marked "*" on parts list are damaged, loosened or removed. 3 - 1 R-231NW CHAPTER 3. It is not any other visible damage with Operation and Service Information for the SHARP MICROWAVE OVENS, R-230KK and R-230KW. Servicing and repair work must be qualified to provide...
Service Manual
Page 24
... FOR WIRING To prevent an electric shock, take the following conditions exist; 1. Insert the positive lock connector until its pin is damaged. 3. R-231NW CHAPTER 11. Visually check the door and cavity face plate for 60 seconds. 2. There are pulled. 5. There is unlatched. (Hold the door...voltage transformer, High voltage capacitor, High voltage rectifier assembly. 2) Hot parts: Oven lamp, Magnetron, Power transformer and Oven cavity. 3) Sharp edge: Bottom plate, Oven cavity, Waveguide flange, other , this causes the latch leads to rise, it open button with the other...
... FOR WIRING To prevent an electric shock, take the following conditions exist; 1. Insert the positive lock connector until its pin is damaged. 3. R-231NW CHAPTER 11. Visually check the door and cavity face plate for 60 seconds. 2. There are pulled. 5. There is unlatched. (Hold the door...voltage transformer, High voltage capacitor, High voltage rectifier assembly. 2) Hot parts: Oven lamp, Magnetron, Power transformer and Oven cavity. 3) Sharp edge: Bottom plate, Oven cavity, Waveguide flange, other , this causes the latch leads to rise, it open button with the other...
Service Manual
Page 27
...RE-USE THE REMOVED FAN BLADE BECAUSE THE HOLE (FOR SHAFT) MAY BE LARGER THAN NORMAL. 10.Now, the fan motor is free. R-231NW [9] POWER SUPPLY CORD REPLACEMENT 1. Disconnect the power supply cord, and remove outer case. 2. Open the door and block it open . ... voltage capacitor. 4. Figure C-3(a) Power Supply Cord Replacement [10] TURNTABLE MOTOR REMOVAL 1. Now, the turntable motor is operating properly. REMOVAL 1. No sharp edges must be free. Disconnect wire leads from the turntable motor. 8. Figure C-4. TTM packing Turntable motor [11] COOLING FAN MOTOR REMOVAL 1. Disconnect...
...RE-USE THE REMOVED FAN BLADE BECAUSE THE HOLE (FOR SHAFT) MAY BE LARGER THAN NORMAL. 10.Now, the fan motor is free. R-231NW [9] POWER SUPPLY CORD REPLACEMENT 1. Disconnect the power supply cord, and remove outer case. 2. Open the door and block it open . ... voltage capacitor. 4. Figure C-3(a) Power Supply Cord Replacement [10] TURNTABLE MOTOR REMOVAL 1. Now, the turntable motor is operating properly. REMOVAL 1. No sharp edges must be free. Disconnect wire leads from the turntable motor. 8. Figure C-4. TTM packing Turntable motor [11] COOLING FAN MOTOR REMOVAL 1. Disconnect...
Service Manual
Page 41
AF AE AM AA AA AC AA AA AA AA COPYRIGHT© 2009 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in retrieval systems, or transmitted in... any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. 6 R-231NW ■ INDEX PARTS CODE [ D ] DPWBFC479WRUZ [ F ] FACCDA107WREZ FACCDA108WREZ FDORFA397WRTZ FFS-BA026WRKZ FH-DZA114WRKZ FPNLCB845WRKZ FPNLCB846WRKZ FPWBFA385WRKZ FROLPA101WRKZ FW-VZC044WREZ [ G ] GCABUA958WRPZ ...
AF AE AM AA AA AC AA AA AA AA COPYRIGHT© 2009 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in retrieval systems, or transmitted in... any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. 6 R-231NW ■ INDEX PARTS CODE [ D ] DPWBFC479WRUZ [ F ] FACCDA107WREZ FACCDA108WREZ FDORFA397WRTZ FFS-BA026WRKZ FH-DZA114WRKZ FPNLCB845WRKZ FPNLCB846WRKZ FPWBFA385WRKZ FROLPA101WRKZ FW-VZC044WREZ [ G ] GCABUA958WRPZ ...