Operating Instructions
Page 6
Maintenance Other Maintenance 34 (GB) Replacing the Lamp 34 (GB) Cleaning the Air Filter 35 (GB) Troubleshooting 36 (GB) Specifications 38 (GB) Index 42 (GB) 6 (GB)
Maintenance Other Maintenance 34 (GB) Replacing the Lamp 34 (GB) Cleaning the Air Filter 35 (GB) Troubleshooting 36 (GB) Specifications 38 (GB) Index 42 (GB) 6 (GB)
Operating Instructions
Page 34
.... If you touch the lamp unit, you replace the lamp, wait for at least an hour for the lamp to change the lamp, a message which says, "Please replace the LAMP." Maintenance Maintenance Notes • If the lamp breaks, consult with qualified Sony personnel. • Pull out the lamp unit by loosening one after turning off the projector, then unplug the power...
.... If you touch the lamp unit, you replace the lamp, wait for at least an hour for the lamp to change the lamp, a message which says, "Please replace the LAMP." Maintenance Maintenance Notes • If the lamp breaks, consult with qualified Sony personnel. • Pull out the lamp unit by loosening one after turning off the projector, then unplug the power...
Operating Instructions
Page 35
Maintenance 6 Close the lamp cover and tighten the screw. 7 Turn the projector back over. 8 Connect the power cord and turn the projector to the standby mode. 9 Press the following keys on the control panel in the following order for less than in five seconds each: RESET,
Maintenance 6 Close the lamp cover and tighten the screw. 7 Turn the projector back over. 8 Connect the power cord and turn the projector to the standby mode. 9 Press the following keys on the control panel in the following order for less than in five seconds each: RESET,
Operating Instructions
Page 36
...the SET SETTING menu has Set STATUS in the input signals and LCD pixels. Connect the remote control cable to output from an external monitor. Troubleshooting Troubleshooting If the projector appears to be operating erratically, try to OFF. (see page ...27 (GB)). Close the air filter cover securely (see page 20 (GB)). The computer output signals are dead. Invalid input setting. The lamp cover is not connected to the input signal. On-screen display does not appear. Remedy Replace with qualified Sony...
...the SET SETTING menu has Set STATUS in the input signals and LCD pixels. Connect the remote control cable to output from an external monitor. Troubleshooting Troubleshooting If the projector appears to be operating erratically, try to OFF. (see page ...27 (GB)). Close the air filter cover securely (see page 20 (GB)). The computer output signals are dead. Invalid input setting. The lamp cover is not connected to the input signal. On-screen display does not appear. Remedy Replace with qualified Sony...
Operating Instructions
Page 37
... (see if nothing is blocking the ventilation holes. Consult with qualified Sony personnel. Lamp off the power. Please replace the LAMP. Meaning Remedy Internal temperature is unusually high. Please replace the lamp. Press the appropriate key. 37 (GB) The lamp has reached the end of the projector. Message High temp.! Please check INPUT-B setting. This input signal cannot...
... (see if nothing is blocking the ventilation holes. Consult with qualified Sony personnel. Lamp off the power. Please replace the LAMP. Meaning Remedy Internal temperature is unusually high. Please replace the lamp. Press the appropriate key. 37 (GB) The lamp has reached the end of the projector. Message High temp.! Please check INPUT-B setting. This input signal cannot...
Operating Instructions
Page 39
For details, please consult your nearest Sony office. 39 (GB) Other VD: Vertical sync input: 1-5 Vp-p high impedance, positive/ negative REMOTE RS-232C: D-sub 9-pin (female) CONTROL S IN/PLUG... (no condensation) Storage temperature -20°C to 60°C (-4°F to 140°F) Storage humidity 10% to change without notice. Specifications Optional accessories Projector Lamp LMP-P200 (for replacement) (1) Operating Instructions (1) Design and specifications are subject to 90% Supplied accessories Remote Commander RM-PJVW10 (1) Size AA (R6) batteries (2) Lens Cap (1) ...
For details, please consult your nearest Sony office. 39 (GB) Other VD: Vertical sync input: 1-5 Vp-p high impedance, positive/ negative REMOTE RS-232C: D-sub 9-pin (female) CONTROL S IN/PLUG... (no condensation) Storage temperature -20°C to 60°C (-4°F to 140°F) Storage humidity 10% to change without notice. Specifications Optional accessories Projector Lamp LMP-P200 (for replacement) (1) Operating Instructions (1) Design and specifications are subject to 90% Supplied accessories Remote Commander RM-PJVW10 (1) Size AA (R6) batteries (2) Lens Cap (1) ...
Operating Instructions
Page 42
... 27 (GB) INSTALLATION 28 (GB) Installation examples 29 (GB) on a ceiling 30 (GB) on a floor 29 (GB) KEYSTONE MEM 27 (GB) Index L Lamp replacement 34 (GB) LAMP TIMER 28 (GB) LANGUAGE 27 (GB) Location and function of controls connector panel 12 (GB) control panel 11 (GB) front/left side 9 (GB) rear... 22 (GB) Power turn off 20 (GB) turn on 18 (GB) POWER SAVING 11 (GB), 27 (GB) Precautions 7 (GB) Projecting 18 (GB) PSS-610 Projector Suspension Support 30 (GB) R Remote Commander battery installation 14 (GB) location and function of controls 13 (GB) Remote control detector front 9 (GB) rear 9 (GB)...
... 27 (GB) INSTALLATION 28 (GB) Installation examples 29 (GB) on a ceiling 30 (GB) on a floor 29 (GB) KEYSTONE MEM 27 (GB) Index L Lamp replacement 34 (GB) LAMP TIMER 28 (GB) LANGUAGE 27 (GB) Location and function of controls connector panel 12 (GB) control panel 11 (GB) front/left side 9 (GB) rear... 22 (GB) Power turn off 20 (GB) turn on 18 (GB) POWER SAVING 11 (GB), 27 (GB) Precautions 7 (GB) Projecting 18 (GB) PSS-610 Projector Suspension Support 30 (GB) R Remote Commander battery installation 14 (GB) location and function of controls 13 (GB) Remote control detector front 9 (GB) rear 9 (GB)...