Sony XVS-9000 Support and Manuals
Get Help and Manuals for this Sony item
This item is in your list!
View All Support Options Below
Free Sony XVS-9000 manuals!
Problems with Sony XVS-9000?
Ask a Question
Free Sony XVS-9000 manuals!
Problems with Sony XVS-9000?
Ask a Question
Popular Sony XVS-9000 Manual Pages
Users Guide - Page 3
... 8 • DME channel 5 to 8 operation and settings • DME channel 5 to 8 related bus operation and settings • DME channel 5 to setup
Classification NS-Bus
Functions supported
Menu No.
XKS-C8111/
XKS-C9111/
XKS-C9121/
XKS-C8166 720P
format
page 443 page 454
Format converter
XVS-9000 internal format converter settings (with resource sharing enabled only)
7332.11...
Users Guide - Page 15
...
AUX Bus Remote Panel 533 Procedure for Simple Connection 533 Setting Status of the MKS-8080/8082 in
Simple Connection 534 ...Setup Define 548 Data Saved by [Init Status Define 549 Error Messages 552 Error Messages Displayed in the Error
Status/Error Log Menu 552 Error Messages Appearing in a Message
Box 553 Error Messages Shown in the Error
Information Menu 558 Maintenance 559
Replacing...
Users Guide - Page 60
... a button and click the mouse instead of the control panel setup. The shortcut menu settings are available.
60 You can register 15 buttons in the Setup menu.
Registering a menu in the shortcut menu
You can recall and save these settings in the same way as part of pressing (touching) a button on the initial status mode...
Users Guide - Page 67
...XVS-9000/8000/ 7000/6000 Installation Manual. The output setting is also output on the number of the XVS system. n -AC IN (AC power input) connectors (3-pin) XVS-9000: A, B, C, D, E, and F connectors XVS-8000/7000: A, B, C, and D connectors XVS...XVS-8000, the same signals on the SPARE 1, 2, 3, and 4 connectors.
For details about supported Ethernet switches, contact your Sony service...
Users Guide - Page 123
...and PROC K signals on each switcher bank cannot be configured. Blink
The following effects can set the following parameters.
No. This assigns the key fill and key source signals, processed using... selection in step 2, set the blinking cycle time, and the proportion of the menu display, turning it on
When [Edge Blink] is selected on . Key blink: The key is replaced by the key fill ...
Users Guide - Page 259
... to which the image disappears, the trail type and amount of stardust, and other parameters. Down: Melting occurs downward.
2 To make wave settings for the melting part, press
[Border] and set
the following parameters. Parameter Adjustment
1
Amp
Amplitude of wave
2
Freq
Frequency of wave
3
Offset a) Wave phase shift offset
4
Speed b) Direction of travel...
Users Guide - Page 387
...unit IDs for each device. For details about unit IDs of the NFS server to the installation manual for DMEs are set the unit ID: Check the message, then press [No] and skip to step 4.
4..., then press [Enter].
3 Perform the following operations.
System Setup
17 Chapter
About system setup
This configures the setup for the whole system. Setting the Group ID and Unit ID of 2nd switcher (Ch1 to...
Users Guide - Page 390
...Setup >System >Network Config menu (7311), press [IP Address]. Disable DHCP when not performing the initial setup.
5 In the group, press [IP Address],
and set...configuration. The unit supports 25G×4 to set the IP address....sets the IP address for the network with the lowest number is installed, LSM cannot be set when DHCP is set for each network.
7 In the group, press [Gateway],
and set...
Users Guide - Page 397
... can also configure the restoration of the
following.
16:9: Set the screen aspect ratio to 16:9. 4:3: Set the screen aspect ratio to set Setup mode and Initial Status mode settings separately. • Setup mode: Set one of the following setup states to 16:9.
2 In the group, select one of settings that were previously saved when recalling an initial status...
Users Guide - Page 403
... selected menus become candidates for operation in the "Lock" field.
Changing the lock password
1 In the Engineering Setup >System >Maintenance
>Setup Operation Lock menu (7317.1), press [Change Password].
2 Check the message, then press [Yes].
3 Follow the on-screen instructions to set as the primary device.
To deselect all lock candidates.
Note that it is not possible...
Users Guide - Page 404
...] turns red, and a padlock icon appears. To deselect all lock candidates. Changing the lock password
1 In the Engineering Setup >System >Maintenance
>File Load Lock menu (7317.2), press [Change Password].
2 Check the message, then press [Yes].
3 Follow the on-screen instructions to white.
To deselect a lock candidate Select a lock candidate category, and press [Lock].
4 Repeat...
Users Guide - Page 525
4K Format Restrictions
In 4K format, the following function and settings restrictions apply.
Item Functions that cannot be used in the switcher
DMEs
Screen aspect Transitions
Restrictions
• M/E-5 bank (XVS-9000/8000), M/E-3 to M/E-5 banks (XVS-7000), M/E-2 to M/E-5 banks (XVS-6000) a)
• Key 5 to key 8 (3840×2160P), key 3 to key 8 (3840×2160PsF)
• M/E Config multi...
Users Guide - Page 526
...
For the administrator user name and password, refer to the ICP-X7000 Installation Manual.
1 Access Resource Share Setup. Functions relating to DMEs not supported
a) When a dedicated input is used, signals configured using the Engineering Setup >Switcher >Input >Dedicated Input Assign menu (7332.10) can also be used.
• You can set to [Key3 + Key PVW].
Resource Sharing...
Users Guide - Page 529
... from Resource Share Setup Click/tap [Logout], check the message, then click/tap [Yes].
529 Note
In 4K format, the resources for input use the FC channels for the four channels are set dedicated mode Select [Dedicated].
6 Click/tap [Execute].
7 Check the message, then click/tap [Yes].
Multi viewer output settings (XVS-9000 only) Click...
Users Guide - Page 563
...Network interface 388 NFS 376, 387 setting 387
Network AUX remote panel 535 Network interface
Initialize 388 protocol 392 service port 388 setting 388 Network port external devices 478 ...setting 59
Parameter group button 54 Parameter setting buttons 54 Paths 298, 317 Pattern limit 93
setting buttons 30, 32 Pattern mix 141 Pause
keyframes 297 macro 347 Payload ID 396 P-Bus setting 427, 478 supported...
Sony XVS-9000 Reviews
Do you have an experience with the Sony XVS-9000 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Sony yet.
Earn 750 points for your review!