Product Instruction Manual
Page 30
.... : Go to "Mounting the Mowing Head" or "Mounting Metal Cutting Tools". FS 130, FS 130 R 29 see next section on the shaft (2) until the stop pin slips into position and blocks the shaft. Mounting the mowing head Keep instruction sheet for mowing head in the ... 7 Removing Mounting Hardware : Block the shaft - English / USA The rider plate (4) is in the parts kit supplied with machine or available as special accessories) in the hole (8) in a safe place : Screw the STIHL SuperCut 20-2, STIHL AutoCut 25-2, 30-2 STIHL TrimCut 30-2 or STIHL PolyCut 20-3 counterclockwise onto the...
.... : Go to "Mounting the Mowing Head" or "Mounting Metal Cutting Tools". FS 130, FS 130 R 29 see next section on the shaft (2) until the stop pin slips into position and blocks the shaft. Mounting the mowing head Keep instruction sheet for mowing head in the ... 7 Removing Mounting Hardware : Block the shaft - English / USA The rider plate (4) is in the parts kit supplied with machine or available as special accessories) in the hole (8) in a safe place : Screw the STIHL SuperCut 20-2, STIHL AutoCut 25-2, 30-2 STIHL TrimCut 30-2 or STIHL PolyCut 20-3 counterclockwise onto the...
Product Instruction Manual
Page 31
STIHL SuperCut 20-2, STIHL AutoCut 25-2, 30-2, STIHL TrimCut 30-2, STIHL PolyCut 20-3 : Unscrew the mowing head clockwise. tap it locates against the base. : Block the output shaft. : Screw the mounting nut (4) with the combination wrench (5) counterclockwise on the ground once ... surplus line to instructions supplied with the mowing head. 30 FS 130, FS 130 R about 1 1/4"(3 cm) fresh line is still min. 2 1/2" (6 cm) long. Replacing nylon line or PolyCut blades Refer to the correct length. English / USA 5 4 3 1 2 STIHL FixCut 25-2 : Place the mowing head on the thrust...
STIHL SuperCut 20-2, STIHL AutoCut 25-2, 30-2, STIHL TrimCut 30-2, STIHL PolyCut 20-3 : Unscrew the mowing head clockwise. tap it locates against the base. : Block the output shaft. : Screw the mounting nut (4) with the combination wrench (5) counterclockwise on the ground once ... surplus line to instructions supplied with the mowing head. 30 FS 130, FS 130 R about 1 1/4"(3 cm) fresh line is still min. 2 1/2" (6 cm) long. Replacing nylon line or PolyCut blades Refer to the correct length. English / USA 5 4 3 1 2 STIHL FixCut 25-2 : Place the mowing head on the thrust...
Product Instruction Manual
Page 32
.... Mounting Metal Cutting Tools Remove the skirt and blade from the mowing head deflector before mounting the circular saw blade 200 (4,5) - FS 130, FS 130 R 31 see arrows) must point clockwise. Direction of cutting head deflector or limit stop before mounting grass cutting blade 230-4 (1), ... of (1) and (3) may point in cutting tool's mounting hole. : Slip thrust washer (8) and rider plate (9) over the output shaft (10). : Block the output shaft and : Screw the mounting nut (11) with the gearhead facing upward. Cutting edges of (2), (4) and (5) must locate in either direction...
.... Mounting Metal Cutting Tools Remove the skirt and blade from the mowing head deflector before mounting the circular saw blade 200 (4,5) - FS 130, FS 130 R 31 see arrows) must point clockwise. Direction of cutting head deflector or limit stop before mounting grass cutting blade 230-4 (1), ... of (1) and (3) may point in cutting tool's mounting hole. : Slip thrust washer (8) and rider plate (9) over the output shaft (10). : Block the output shaft and : Screw the mounting nut (11) with the gearhead facing upward. Cutting edges of (2), (4) and (5) must locate in either direction...