TL-SL2210 V1 Datasheet
Page 1
... enhanced tra c management capabilities to -use web management interfaces, along with CLI, SNMP and RMON, mean faster setup and con guration with 8 10/100Mbps RJ45 ports, 1 10/100/1000Mbps RJ45 ports and 1 SFP slot. www.tp-link.com Copyright © 2013 TP-LINK Technologies Co., Ltd. The Storm Control feature protects against broadcast, multicast and unknown unicast storm. For workgroup and departments requiring cost-sensitive layer 2 switch and gigabit capability, TP-LINK Smart Switch TL-SL2210 provides you the...
... enhanced tra c management capabilities to -use web management interfaces, along with CLI, SNMP and RMON, mean faster setup and con guration with 8 10/100Mbps RJ45 ports, 1 10/100/1000Mbps RJ45 ports and 1 SFP slot. www.tp-link.com Copyright © 2013 TP-LINK Technologies Co., Ltd. The Storm Control feature protects against broadcast, multicast and unknown unicast storm. For workgroup and departments requiring cost-sensitive layer 2 switch and gigabit capability, TP-LINK Smart Switch TL-SL2210 provides you the...
TL-SL2210 V1 Datasheet
Page 2
...~L4 ACL) Storm Control SSL and SSH encryptions DHCP Filtering Management Web-based GUI Command Line Interface SNMP v1/v2c/v3 RMON (1, 2, 3, 9 group) TP-LINK 8-Port 10/100Mbps + 2-Port Gigabit Smart Switch TL-SL2210 Advanced QoS Features To integrate voice, data and video service on a port level to use and manage. SNMP (v1/v2c/v3) and RMON support enables the switch to ensure that voice and video are not included www.tp-link.com Copyright © 2013 TP-LINK Technologies Co., Ltd. Datasheet Layer 2 Features Link Aggregation Control Protocol (LACP) Static Link Aggregation 64 VLANs...
...~L4 ACL) Storm Control SSL and SSH encryptions DHCP Filtering Management Web-based GUI Command Line Interface SNMP v1/v2c/v3 RMON (1, 2, 3, 9 group) TP-LINK 8-Port 10/100Mbps + 2-Port Gigabit Smart Switch TL-SL2210 Advanced QoS Features To integrate voice, data and video service on a port level to use and manage. SNMP (v1/v2c/v3) and RMON support enables the switch to ensure that voice and video are not included www.tp-link.com Copyright © 2013 TP-LINK Technologies Co., Ltd. Datasheet Layer 2 Features Link Aggregation Control Protocol (LACP) Static Link Aggregation 64 VLANs...
TL-SL2210 V1 Datasheet
Page 4
... Service (QoS) Support 802.1p CoS/DSCP Priority Support 4 priority queues Queue scheduling: SP, WRR, SP+WRR Port/Flow-based rate limiting Voice VLAN assures voice applications much smoother performance Advanced Security Strategies Support broadcast, multicast and unknown unicast Storm Control Static/Dynamic Port Security (MAC-based) Access Control List (ACL)-L2~L4 package ltering based on source and destination MAC address, IP address, TCP/UDP ports SSL and SSH encryptions Management Support web-based GUI management mode Support Command Line Interface(CLI) through telnet management mode SNMP...
... Service (QoS) Support 802.1p CoS/DSCP Priority Support 4 priority queues Queue scheduling: SP, WRR, SP+WRR Port/Flow-based rate limiting Voice VLAN assures voice applications much smoother performance Advanced Security Strategies Support broadcast, multicast and unknown unicast Storm Control Static/Dynamic Port Security (MAC-based) Access Control List (ACL)-L2~L4 package ltering based on source and destination MAC address, IP address, TCP/UDP ports SSL and SSH encryptions Management Support web-based GUI management mode Support Command Line Interface(CLI) through telnet management mode SNMP...
TL-SL2210 V1 User Guide 1910010924
Page 10
... settings of spanning tree function. Port Config: Configure CIST parameters of the switch. Access Security: Provide different security measures for the port. LAG: Configure Link Aggregation Group. Here mainly introduces: System Info: Configure the description, system time and network parameters of the switch. User Management: Configure the user name and password for users to log on each port. MAC Address: Configure the address table of the switch. DHCP Filtering: Monitor the process of the switch. This module is used...
... settings of spanning tree function. Port Config: Configure CIST parameters of the switch. Access Security: Provide different security measures for the port. LAG: Configure Link Aggregation Group. Here mainly introduces: System Info: Configure the description, system time and network parameters of the switch. User Management: Configure the user name and password for users to log on each port. MAC Address: Configure the address table of the switch. DHCP Filtering: Monitor the process of the switch. This module is used...
TL-SL2210 V1 User Guide 1910010924
Page 11
...10 ACL This module is used to configure SNMP function to provide a management frame to CONTENTS 4 configure storm control feature to filter broadcast, multicast and UL frame in this manual. Appendix A Specifications Lists the hardware specifications of SNMP function. Notification: Configure notification function for various network applications and requirements. Appendix B Configure the PCs Introduces how to manage the switch. Here mainly introduces: SNMP Config: Configure global settings of the switch. Return to monitor and maintain the network devices...
...10 ACL This module is used to configure SNMP function to provide a management frame to CONTENTS 4 configure storm control feature to filter broadcast, multicast and UL frame in this manual. Appendix A Specifications Lists the hardware specifications of SNMP function. Notification: Configure notification function for various network applications and requirements. Appendix B Configure the PCs Introduces how to manage the switch. Here mainly introduces: SNMP Config: Configure global settings of the switch. Return to monitor and maintain the network devices...
TL-SL2210 V1 User Guide 1910010924
Page 12
...-standardized framework and smart configuration capacity can fully meet the need of the users demanding higher networking performance. 2.2 Main Features Resiliency and Availability + IEEE 802.1s Multiple Spanning Tree provides high link availability in bring abundant management policies. SNMP, RMON, WEB/Telnet Log-in multiple VLAN environments. + Multicast snooping automatically prevents flooding of IP multicast traffic. + Root Guard protects root bridge from TP-LINK provides wire-speed performance and full set of TL-SL2210 5
...-standardized framework and smart configuration capacity can fully meet the need of the users demanding higher networking performance. 2.2 Main Features Resiliency and Availability + IEEE 802.1s Multiple Spanning Tree provides high link availability in bring abundant management policies. SNMP, RMON, WEB/Telnet Log-in multiple VLAN environments. + Multicast snooping automatically prevents flooding of IP multicast traffic. + Root Guard protects root bridge from TP-LINK provides wire-speed performance and full set of TL-SL2210 5
TL-SL2210 V1 User Guide 1910010924
Page 23
... access the switch via any port on the switch. Figure 4-7 System IP The following page. Changing the IP address to a port that is 192.168.0.1 and you should enter IP Address, Subnet Mask and Default Gateway manually. DHCP: When this option is selected, the switch will obtain network parameters from the DHCP Server. BOOTP: When this screen: IP Config MAC Address: Displays MAC Address of the Management VLAN. You can configure...
... access the switch via any port on the switch. Figure 4-7 System IP The following page. Changing the IP address to a port that is 192.168.0.1 and you should enter IP Address, Subnet Mask and Default Gateway manually. DHCP: When this option is selected, the switch will obtain network parameters from the DHCP Server. BOOTP: When this screen: IP Config MAC Address: Displays MAC Address of the Management VLAN. You can configure...
TL-SL2210 V1 User Guide 1910010924
Page 24
... and default gateway can configure the access level of the switch. Figure 4-8 User Table 4.2.2 User Config On this page you can view the settings without any explanation. The guest only can see the configuration of the switch from DHCP server until success. 4. The Web management pages contained in the DHCP server; By default, the IP address is selected but no DHCP server exists in the network, the switch will replace the original IP address. 3. The IP address configured will...
... and default gateway can configure the access level of the switch. Figure 4-8 User Table 4.2.2 User Config On this page you can view the settings without any explanation. The guest only can see the configuration of the switch from DHCP server until success. 4. The Web management pages contained in the DHCP server; By default, the IP address is selected but no DHCP server exists in the network, the switch will replace the original IP address. 3. The IP address configured will...
TL-SL2210 V1 User Guide 1910010924
Page 90
... being broadcasted in the VLAN owning the receiving port. VLAN ID Multicast IP Port Figure 8-3 Multicast Address Table IGMP Snooping In the network, the hosts apply to the router port list with its router port time will duplicate this multicast, if yes, the router will remove the port from the multicast address table if the switch receives no response from the host, the router sends the Group-Specific Query message of different types as Figure 8-3 below. The...
... being broadcasted in the VLAN owning the receiving port. VLAN ID Multicast IP Port Figure 8-3 Multicast Address Table IGMP Snooping In the network, the hosts apply to the router port list with its router port time will duplicate this multicast, if yes, the router will remove the port from the multicast address table if the switch receives no response from the host, the router sends the Group-Specific Query message of different types as Figure 8-3 below. The...
TL-SL2210 V1 User Guide 1910010924
Page 95
... VLAN Config page will be solved by configuring a multicast VLAN. This saves the bandwidth since multicast streams are transmitted only within the multicast VLAN. Note: The settings here will be broadcasted. 8.1.4 Multicast VLAN In old multicast transmission mode, when users in different VLANs apply for other VLANs on the 802.1Q VLAN page. If a VLAN has no multicast parameters configuration, it indicates the IGMP Snooping is not enabled in the VLAN, thus the multicast data in different VLANs...
... VLAN Config page will be solved by configuring a multicast VLAN. This saves the bandwidth since multicast streams are transmitted only within the multicast VLAN. Note: The settings here will be broadcasted. 8.1.4 Multicast VLAN In old multicast transmission mode, when users in different VLANs apply for other VLANs on the 802.1Q VLAN page. If a VLAN has no multicast parameters configuration, it indicates the IGMP Snooping is not enabled in the VLAN, thus the multicast data in different VLANs...
TL-SL2210 V1 User Guide 1910010924
Page 97
... IGMP Snooping Status table on the VLAN→802.1Q VLAN page. Configure the link type of the router ports as Tagged. 3 Configure parameters for Optional. It is recommended to keep the default time parameters. 4 Look over the configuration If it is connected to port 5 of the switch. User B: Connected to the router and the packets are transmitted in VLAN4; Enable and configure a multicast VLAN on Multicast→IGMP Snooping→Snooping Config and Port Config page. 2 Create a multicast VLAN Required. its LAN port is connected to user...
... IGMP Snooping Status table on the VLAN→802.1Q VLAN page. Configure the link type of the router ports as Tagged. 3 Configure parameters for Optional. It is recommended to keep the default time parameters. 4 Look over the configuration If it is connected to port 5 of the switch. User B: Connected to the router and the packets are transmitted in VLAN4; Enable and configure a multicast VLAN on Multicast→IGMP Snooping→Snooping Config and Port Config page. 2 Create a multicast VLAN Required. its LAN port is connected to user...
TL-SL2210 V1 User Guide 1910010924
Page 159
... or RMON probe. MD5 is a one of digits, also called a message digest. Link Aggregation See Port Trunk. Network Time Protocol (NTP) NTP provides the mechanisms to identify IP Multicast group members. The time servers operate in a hierarchical-master-slave configuration in order to report on MAC addresses. This is used to the hardware interface for troubleshooting with 32 bit machines and is made the "querier" and assumes responsibility...
... or RMON probe. MD5 is a one of digits, also called a message digest. Link Aggregation See Port Trunk. Network Time Protocol (NTP) NTP provides the mechanisms to identify IP Multicast group members. The time servers operate in a hierarchical-master-slave configuration in order to report on MAC addresses. This is used to the hardware interface for troubleshooting with 32 bit machines and is made the "querier" and assumes responsibility...
TL-SL2210 V1 CLI Reference Guide 1910010922
Page 12
...: Port Mirror Commands Provide information about the commands used for configuring the MSTP (Multiple Spanning Tree Protocol). Chapter 16: Loopback Detection Commands Provide information about the commands used for Address configuration. Provide information about the commands used for configuring the Loopback Detection function. Chapter 17: ACL Commands Provide information about the commands used for Ethernet ports. Chapter 12: Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control, Negotiation Mode, and Storm Control...
...: Port Mirror Commands Provide information about the commands used for configuring the MSTP (Multiple Spanning Tree Protocol). Chapter 16: Loopback Detection Commands Provide information about the commands used for Address configuration. Provide information about the commands used for configuring the Loopback Detection function. Chapter 17: ACL Commands Provide information about the commands used for Ethernet ports. Chapter 12: Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control, Negotiation Mode, and Storm Control...
TL-SL2210 V1 CLI Reference Guide 1910010922
Page 15
... from User EXEC mode. Mode Accessing Path Prompt Logout or Access the next mode User EXEC Mode Primary mode once it is connected with the switch. Enter the configure command to access interface Configuration mode. Use the exit or the end command or press Ctrl+Z to return to access VLAN Configuration mode. 5 Use the vlan vlan-list to Privileged EXEC mode. Use the enable command to User EXEC mode. User EXEC Mode password Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode Interface fastEthernet Interface gigabitEthernet Interface link-aggregation...
... from User EXEC mode. Mode Accessing Path Prompt Logout or Access the next mode User EXEC Mode Primary mode once it is connected with the switch. Enter the configure command to access interface Configuration mode. Use the exit or the end command or press Ctrl+Z to return to access VLAN Configuration mode. 5 Use the vlan vlan-list to Privileged EXEC mode. Use the enable command to User EXEC mode. User EXEC Mode password Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode Interface fastEthernet Interface gigabitEthernet Interface link-aggregation...
TL-SL2210 V1 CLI Reference Guide 1910010922
Page 63
... displayed as manual, and the time is 12/20/2010 17:30:35 TL-SL2428(config)# system-time manual 12/20/2010-17:30:35 system-time ntp Description The system-time ntp command is used to a NTP Server. TimeZone for the NTP Server. Set the date and time manually, MM/DD/YYYY-HH:MM:SS Command Mode Global Configuration Mode Example Configure the system mode as follow: UTC-12:00 -- Syntax system-time ntp { timezone } { ntp-server } { backup-ntp-server } { fetching-rate } Parameter...
... displayed as manual, and the time is 12/20/2010 17:30:35 TL-SL2428(config)# system-time manual 12/20/2010-17:30:35 system-time ntp Description The system-time ntp command is used to a NTP Server. TimeZone for the NTP Server. Set the date and time manually, MM/DD/YYYY-HH:MM:SS Command Mode Global Configuration Mode Example Configure the system mode as follow: UTC-12:00 -- Syntax system-time ntp { timezone } { ntp-server } { backup-ntp-server } { fetching-rate } Parameter...
TL-SL2210 V1 CLI Reference Guide 1910010922
Page 71
... Interface Configuration Mode of the management VLAN. After resetting, all configuration of the switch will restore to the factory defaults and your current settings will obtain IP address from BOOTP Server when the management VLAN of the switch is VLAN1: TL-SL2428(config)# interface vlan 1 TL-SL2428(config-if)# ip address-alloc bootp reset Description The reset command is used to enable the BOOTP Protocol. This command should be lost. Example Enable the DHCP Client function when the management VLAN of the switch is VLAN1: TL-SL2428(config)# interface vlan 1 TL-SL2428(config...
... Interface Configuration Mode of the management VLAN. After resetting, all configuration of the switch will restore to the factory defaults and your current settings will obtain IP address from BOOTP Server when the management VLAN of the switch is VLAN1: TL-SL2428(config)# interface vlan 1 TL-SL2428(config-if)# ip address-alloc bootp reset Description The reset command is used to enable the BOOTP Protocol. This command should be lost. Example Enable the DHCP Client function when the management VLAN of the switch is VLAN1: TL-SL2428(config)# interface vlan 1 TL-SL2428(config...
TL-SL2210 V1 CLI Reference Guide 1910010922
Page 139
... Configuration Mode Example Enable Multicast VLAN 3, and configure Router Port Time as to 30 in seconds. The range for receivers to join is used to configure the multicast IP-range desired to 239.255.255.255. The Ethernet port number. To delete the corresponding IP-range, please use no ip igmp snooping filter addr-id addr-id list Parameter addr-id list -- Multicast IP addresses ranges from 1 to restrict users ordering multicast programs via configuring multicast filter rules. Command Mode Interface Configuration Mode (interface...
... Configuration Mode Example Enable Multicast VLAN 3, and configure Router Port Time as to 30 in seconds. The range for receivers to join is used to configure the multicast IP-range desired to 239.255.255.255. The Ethernet port number. To delete the corresponding IP-range, please use no ip igmp snooping filter addr-id addr-id list Parameter addr-id list -- Multicast IP addresses ranges from 1 to restrict users ordering multicast programs via configuring multicast filter rules. Command Mode Interface Configuration Mode (interface...
TL-SL2210 V1 CLI Reference Guide 1910010922
Page 140
... access port to 30. Otherwise, the switch will add the port to the forward port list of the multicast group. start -ip end-ip no ip igmp snooping filter id Parameter id -- end-ip -- Command Mode Global Configuration Mode Example Modify the multicast IP-range whose ID is 3 as 225.1.1.1~226.3.2.1: TL-SL2428(config)# ip igmp snooping filter 3 225.1.1.1 226.3.2.1 ip igmp snooping filter(interface) Description The ip igmp snooping filter command is used to add or modify the multicast...
... access port to 30. Otherwise, the switch will add the port to the forward port list of the multicast group. start -ip end-ip no ip igmp snooping filter id Parameter id -- end-ip -- Command Mode Global Configuration Mode Example Modify the multicast IP-range whose ID is 3 as 225.1.1.1~226.3.2.1: TL-SL2428(config)# ip igmp snooping filter 3 225.1.1.1 226.3.2.1 ip igmp snooping filter(interface) Description The ip igmp snooping filter command is used to add or modify the multicast...
TL-SL2210 V1 CLI Reference Guide 1910010922
Page 153
... when port status changes from linkup to linkup. Command Mode Global Configuration Mode Example Enable SNMP standard linkup trap for port 3: TL-SL2428(config)# interface fastEthernet 1/0/3 TL- SL2428(config-if)# snmp-server traps link-status 143 It is enabled. By default, it is used to enable SNMP link status trap for the specified port. coldstart -- To disable the sending of SNMP link status trap, please use no snmp-server traps link-status Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface...
... when port status changes from linkup to linkup. Command Mode Global Configuration Mode Example Enable SNMP standard linkup trap for port 3: TL-SL2428(config)# interface fastEthernet 1/0/3 TL- SL2428(config-if)# snmp-server traps link-status 143 It is enabled. By default, it is used to enable SNMP link status trap for the specified port. coldstart -- To disable the sending of SNMP link status trap, please use no snmp-server traps link-status Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface...
TL-SL2210 V1 IG 7106504458
Page 24
... IP address should be set within the subnet of the switch. 555If you still cannot access the configuration page, please restore the switch to 254) and Subnet Mask as 192.168.0.x ("x" is any number from 2 to its factory default settings, and the default login user name and password are recommended to check the following steps: 111Make sure that the power cable is connected properly, and the power contact is set as...
... IP address should be set within the subnet of the switch. 555If you still cannot access the configuration page, please restore the switch to 254) and Subnet Mask as 192.168.0.x ("x" is any number from 2 to its factory default settings, and the default login user name and password are recommended to check the following steps: 111Make sure that the power cable is connected properly, and the power contact is set as...