TRENDnet TEG-S4000 Support and Manuals
Get Help and Manuals for this TRENDnet item
This item is in your list!
View All Support Options Below
Free TRENDnet TEG-S4000 manuals!
Problems with TRENDnet TEG-S4000?
Ask a Question
Free TRENDnet TEG-S4000 manuals!
Problems with TRENDnet TEG-S4000?
Ask a Question
Popular TRENDnet TEG-S4000 Manual Pages
Manual - Page 2
.... No portion of their respective owners.
FCC Statement
This equipment has been tested and found to comply with instructions, may be requires to correct the interference at the user's own expense. Printed in a commercial installation. These limits are the properties of this equipment in a residential area is likely to cause harmful interference...
Manual - Page 6
... the power supply
8 ports 10/100Base-TX Module
Figure 1-4. 8 port 10/100Base-TX Module
When installed into a 4-Slot Modular Switch, the 10/100Base-TX Module provides 8x 10/100Mbps Switch ports which ...-TX and IEEE 802.3x Ethernet Standards
Store and forward switch architecture for abnormal packet filtering
Support for half and full duplex on the network
connected to a port, that Full Duplex/Col...
Manual - Page 8
...) connector provides the link to the backbone of the Module at-a glance. Dip switch location and mode settings
The following Table 1-2. 2 ports 100Base-FX Fiber Module
Figure 1-6. 2 port 100Base-FX Module Front View
When installed into a 4-Slot Modular Switch, this Module provides a 100Mbps Fast Ethernet fiber port which can be used to...
Manual - Page 9
... Fiber Module Features Conforms to IEEE 802.3u Fast Ethernet standard Support for SC or ST fiber connectors (optional) Supports half and full duplex modes via DIP switches Store-and-forward switch...mode type module.
4 Ports 100Base-FX Fiber Module
Figure 1-8. 4 port 100Base-FX Front View
When installed into a 4-Slot Modular Switch, this Module provides 4 x 100Mbps Fast Ethernet fiber ports which can...
Manual - Page 10
Location and setting duplex mode
The following Table1-3. SW ON OFF
PORT 1 1 Half-Duplex Full-Duplex
PORT 2 2 ... DIP switch functions
4 ports 100Base-FX Fiber Module Feature
Conforms to IEEE 802.3u Fast Ethernet standard
Support SC or ST fiber connector (optional)
Support half and full duplex via DIP switches
Store-and-forward switch architecture for abnormal packets filtering
Back-plane up...
Manual - Page 11
...
1000Base-SX/LX Fiber Module
Figure 1-10. 1000Base-SX/LX Front View When installed into a 4-Slot Modular Switch, the 1000Base-SX/LX Module provides 1 Gigabit...-control for MII and GMII PHYs Backpressure for half duplex
1000Base-T Module
Figure 1-11. 1000Base-T Front View When installed into a 4-Slot Modular Switch, the 1000Base-T Module provides 1 Gigabit Ethernet ports which can connect the 4-Slot ...
Manual - Page 12
1x1000Base-T Ethernet Port
128 KBytes packet buffer support
Automatic address learning with 4K address entry storage
Standard auto-negotiation for speed, duplex mode and flow-control for MII and GMII PHYs
Backpressure for half duplex
Manual - Page 13
The maximum network diameter is 500 meters (1,640 feet) for setting up Ethernet networks. The maximum number of hubs on a 10Base-T segment is ...2 km (62.5/125µm), 2 km (50/125µm) in length. Chapter 2 Planning your Network
Before you install your network to take maximum advantage of its switching capabilities.
10Base-T Ethernet Network Guidelines
The maximum length of segments between...
Manual - Page 16
... as a high-speed backbone link to link local area networks into one interconnected network.
The 4-Slot Modular Switch providers multiport bridges with short delays, easy setup and maintenance, making it ideal for backbone links.
Manual - Page 20
... based on a desktop or in a rack. Allow easy access to power transformers or radio transmitters.
Figure 3-1. Chapter 3 Installation
The Switch can install the switch on the following criteria:
Avoid dusty locations. However, for desktop installation Avoid electromagnetic noisy areas, such as locations close to the front panel ports and the rear panel switches...
Manual - Page 21
...is not, check the following: The power switch is lit. Before connecting your switch: 1. Rack Installation Your switch comes with a universal switching power supply that the Power
LED is in the rack ... end of your switch to network devices such as desktops and workgroups or to the rack. Set the power switch to mount the switch on , without interrupting the operation of the power cord...
Manual - Page 22
...above. Do not touch any of the pins, connections or components on a flat surface. Module Setup and Installation
1. Ensure that the Switch is disconnected from the main power supply. The 100Base-TX Fast ...mode or 9/125 micron single-mode fiber. Chapter 4.
make sure that you are ready to install it into the 4-Slot Modular Switch, you are wearing an anti-static wrist-band connected ...
Manual - Page 23
... Fast Ethernet or 10Mbps Ethernet twisted pair interface.
Power up . d. If you must replace the blanking plate to prevent dust and debris from entering the Switch and to aid the... captive thumbscrews that the Switch is powered up the Switch. c. Installing 100Base-FX Modules a. Insert the module
Installing the Modules
Installing 10/100Base-TX Modules a. Plug the ST (or SC) connector...
Manual - Page 24
b. d. Installing 1000Base-T Modules
a. Connect the other end of the fiber optic segment to an appropriate device fitted with a 1000Mbps adapter.
b. c. Technical Specifications
Compatibility with Ethernet Standards:
...end of the UTP segment to aid circulation of the Switch. b. If you must replace the blanking plate to ensure that the Module is operating correctly. Ensure that the Switch...
TRENDnet TEG-S4000 Reviews
Do you have an experience with the TRENDnet TEG-S4000 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for TRENDnet yet.
Earn 750 points for your review!