TRENDnet TEW-503PI Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TEW-503PI manuals!
Problems with TRENDnet TEW-503PI?
Ask a Question
Free TRENDnet TEW-503PI manuals!
Problems with TRENDnet TEW-503PI?
Ask a Question
Popular TRENDnet TEW-503PI Manual Pages
User Guide - Page 5
The package you with the installation procedure. This User's Guide will assist you have received should contain the following items:
• Wireless LAN Adapter (TEW-501PC or TEW-503PI) • Quick Installation Guide • CD containing Wireless network adapter utility & drivers and User's Guide
Note: if anything is missing, please contact your Wireless LAN Adapter.
Introduction
Thank ...
User Guide - Page 6
...-time information anywhere in a variety of topologies to setup and manage and often more cost effective than the cost of specific applications and installations. Thus, WLANs combine data connectivity with wired networks.
• Installation Speed and Simplicity - With wireless LANs, users can access shared information without looking for wireless LAN hardware might be higher than their...
User Guide - Page 9
....
User's Guide
9 Select "Install the software automatically (Recommended)", and then click Next to do so, failure of which may result in the CD-ROM, then the AutoRun page will detect new hardware. Install Procedure for Windows
Note: Do not insert the WLAN Adapter until you are asked to continue. Select TEW501PC or TEW-503PI from the...
User Guide - Page 10
... system, then the setup is PCI interface, then you should shut down your computer first and power on your computer after you complete the card insertion. Note: If the wireless network card is finish.
3.
Insert your wireless network card into your system detected the driver, Microsoft will show a warning message as below. User's Guide
10 Once your computer...
User Guide - Page 13
7. After setting these parameters appropriately, click OK to return to back menu. User's Guide
13 You can select either Obtain an IP address automatically or Use the following IP address setting. If your choice is the second one then entering the IP address, Subnet mask, Defaultgateway and DNS.
User Guide - Page 16
...Points that be shown in Infrastructure mode. User's Guide
16 This field will scan for 5 seconds looking for some reason if the driver fails to initial.
♦ Network Type
Infrastructure... Mode - Networking is used for available Access Point within effective range. The driver will also display an error message for an...
User Guide - Page 19
... Profile Setting
Profile Setting allows user to create profiles for editing current exist profile.
Click "Add" button to Peer" and "Access Point". User's Guide
19
...Click "Delete" button if you wish to delete profiles.
♦ Network Name The name of Profile, users can define it by themselves.
♦ Network Type This field allows you to select from a list of supported...
User Guide - Page 20
...wireless "cell" is 802.11 peer-to-peer mode. This mode of operation requires the presence of AP transmits the data packets. This is supported... User's Guide
20 You may set this to other wireless Clients in...WPA encryption. All communication is done via the Access Point, which relays packets to fixed 1Mbps, fixed 2 Mbps, fixed 5.5 Mbps or higher or Automatic for establishing the wireless...
User Guide - Page 21
...-Shared Key, enter a password in the WPA Shared Key field between 8 and 63 characters long.
To be supported - If entered format is incorrect, the utility will not accept it. There are 2 types algorithm could be written to the driver and registry, such as Hexadecimal format, each key must consist of hex digits, which means...
User Guide - Page 22
When the DHCP Status is determinate by a DHCP Server. User's Guide
22
Or otherwise please fill up with the correspondence data of the IP settings. Please define if the current Profile IP setting will be assign by a DHCP Server or just assign by a fixed IP that is Enable, the TCP/IP information will be...
User Guide - Page 23
4.4 About
"About" tab shows the product version including the detail of Driver, Application and firmware versions. Users must use this version number when reporting their problems to technical support. User's Guide
23
User Guide - Page 24
... to the following website for WPA setup
Step1: Check and make sure that the Wireless Zero Configuration service is running.
Appendix
5.1 Using WinXP Wireless Zero configuration for download it. User's Guide
24 Click Start Æ Settings Æ Control Panel Æ Administrative Tools Æ Services
Since WPA security standard has been defined after Windows XP lunch date, then you...
User Guide - Page 26
... is TKIP or AES. (The encryption type should match the WPA setting of your Access Point.)
Step4: Click Authentication tab to select EAP type. (The EAP type should match the authentication server before access the authenticated network.)
After clicking OK, the Wireless workstation will be able to associate with the AP previously get...
User Guide - Page 27
... IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDWARE'S PRODUCTS. Limited Warranty
TRENDware warrants its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective item, or refund to service the product by any products returned to TRENDware pursuant...
User Guide - Page 28
... from that TEW-501PC and TEW-503PI (FCC ID...installed and used in a residential installation. However, there is connected.
-
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
IMPORTANT NOTE: FCC Radiation Exposure Statement:
This equipment complies with Part...must not be installed and operated with the instructions, may cause...
TRENDnet TEW-503PI Reviews
We have not received any reviews for TRENDnet yet.