Tanaka TCG22EBSP Support and Manuals
Get Help and Manuals for this Tanaka item
View All Support Options Below
Free Tanaka TCG22EBSP manuals!
Problems with Tanaka TCG22EBSP?
Ask a Question
Free Tanaka TCG22EBSP manuals!
Problems with Tanaka TCG22EBSP?
Ask a Question
Popular Tanaka TCG22EBSP Manual Pages
Parts List - Page 4
...1
30 6691242 PUMP PLATE
1
31 6685222 DIAPHRAGM COVER-METERING
1
32 6691312 SET SCREW
4
33 6696829 SET SCREW M3 X 12
2
34 6684695 O-RING
1
35
MAIN JET
1
36... WASHER M6 (10 PCS.)
2
6 6600004 MUFFLER (B)
1
7 6600320 HEAT PROTECTION PANEL
1
8 6698386 HEX.
PARTS
ITEM NO. CODE NO. SOCKET HD. SOCKET HD. BOLT (W/FLANGE) M4 X 18 4
4 6698384 HEX. SOCKET HD.
BOLT ...
Parts List - Page 5
...
1 FOR (SL)
* 97 6699193 RETURN SPRING
1 FOR (SL)
* 98 6699190 STAY SET
1 FOR (SL)
* 99 6699133 THROTTLE LEVER (A) ASS'Y
1 INCLUD.91-98 FOR (SL)
100 6699176 HEX. CODE NO.
50 6684590 CIR CLIP
DESCRIPTION
NO.
BOLT (W/SP.WASHER) M5 X 12 1
101 6695492... BEARING 6301ZZC3
1
109 322813 RETAINING RING 37MM
1
110 6699434 CLUTCH SHAFT
1
4 - 14
*ALTERNATIVE PARTS
TCG 24EBSP - 5 -
Owner's Manual - Page 3
... case
16.Combi box spanner
17.Spanner (if so equipped)
18.Hex bar wrench
19.Swivel cap
20.Handling instructions
10 16
6 4
13
7
9 11
3
1
2
TCG 24EBSP (SL) TCG 27EBSP (SL)
7 ...SL)
3 12
1
17
18
19
20
3 Starter handle
4. English
WHAT IS WHAT
Since this manual covers several models, there may be some difference between pictures and your unit.
5 14
1. Harness
5...
Owner's Manual - Page 4
...Replace parts that are using the unit/ machine. ○ Make sure the cutting attachment is properly installed...9675; Empty the fuel tank before the unit is set down. ○ When operation is prolonged, take...hands and fingers.
WARNINGS AND SAFETY
INSTRUCTIONS
Operator safety ○ Always wear a ...guarantee that the fuel be signaling a problem. English
WARNING The engine exhaust from ...
Owner's Manual - Page 6
engine output (kW)
Fuel tank capacity (fl. English
SPECIFICATIONS
Model
Engine Displacement (cu. in.) Spark plug
Idling speed (min-1) Speed of output shaft (min-1) Max. oz)
Dry weight (Ibs)
Cutting attachment
Type
Sound pressure level ...
Owner's Manual - Page 7
English
Model
Engine Displacement (cu. in.) Spark plug Idling speed (min-1) Speed of output shaft (min-1) Max. engine output (kW)
Fuel tank capacity (fl. oz)
Dry weight (...
Owner's Manual - Page 8
... it and the earth terminal (6) (if so equipped) into the air cleaner cover. (Fig. 6) Some models may come off. (Fig. 1) 3. Adjust the location to the drive shaft tube with the parts installed.
7 6
10
11
5
NOTE
If your unit has handle location label on your unit, screw it . 2. Make sure the lock pin (1) fi...
Owner's Manual - Page 9
...
limiters, the line will become a dangerous projectile.
9
Install the cutting attachment guard on drive shaft tube, follow the...Code No. Fig. 8
○ The cutting head must be securely mounted to the gear case on some models. Function Automatically feeds more nylon cutting line when it .
Installation of semi-auto cutting head
Fig. 6
Installation of the button, change the new parts...
Owner's Manual - Page 10
...and oil in order to the proper length of grass
trimmers/brush cutters. Adjusting line length ○ Set the engine speed as low as possible and tap
the head on gear case of 4-11/32&#...cutting head does not feed cutting line properly, check that the nylon line and all components are properly installed. WARNING For Tanaka heads, use (JASO FC GRADE OIL or ISO EGC GRADE). The nylon line will...
Owner's Manual - Page 11
....
1. NOTE If engine does not start, repeat procedures from stop position. (Fig. 13)
Fig. 15
3. Set ignition switch (16) to forward away from 2 to snap back. (Fig. 16)
16
17
Fig. 13
...* Push priming bulb (18) several times so that no dirt falls into the tank.
Fig. 14
2. Set choke lever (20) to START position (closed) (A). (Fig. 15) 20
B
B
Before fueling, clean the tank...
Owner's Manual - Page 12
...the cutting attachment has stopped before the unit is set down . English
6. Check that the attachment and related parts are undamaged. When grass or vines wrap around ...greater than 4,500 min-1). MAINTENANCE
MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY NONROAD ENGINE REPAIR ESTABLISHMENT OR INDIVIDUAL.
The cutting attachment ...
Owner's Manual - Page 13
...filter that the air filter is idling the cutting attachment must always be replaced with air. When the idle speed is 2,800 - 3,200 min-1. Pull fi... (Fig. 21) T
English
○ Carburetor malfunctions ○ Starting problems ○ Engine power reduction ○ Unnecessary wear on the engine parts ○ Abnormal fuel consumption
Clean the air filter daily or ...
Owner's Manual - Page 14
... is influenced by: ○ An incorrect carburetor setting ○ Wrong fuel mixture (too much oil in the gasoline... badly eroded.
0.024" (0.6 mm)
Semi-auto cutting head
Nylon line replacement (1) Remove the case (22) by removing the grease filler plug...resistor spark plug, use same type of the line through the cord guide (25) when placing the reel in the same direction, keeping each...
Owner's Manual - Page 16
...TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem...Replace with new fuel
Too much fuel is absorbed and spark plug is wet
1.Disconnect the spark plug and allow to dry
2.Pull the starter handle 5 or 6 times to remove the surplus fuel
3.Attach the spark plug 4.Set...dealer
Spark plug is dirty
Replace or clean the spark ...
Owner's Manual - Page 17
...
Contact Tanaka dealer
Engine overheating
Wrong spark plug model
Replace with designated part See "SPECIFICATIONS"
Dirty air cleaner
Clean
Carbon clogging (muffler exhaust port)
Clean
Insufficient compression (piston, piston ring, cylinder)
Contact Tanaka dealer
Cutting attachment is not properly installed
See "Installation of cutting attachment"
Handle, handle bracket or...
Tanaka TCG22EBSP Reviews
We have not received any reviews for Tanaka yet.