Tanaka TCS33EB16S Support and Manuals
Get Help and Manuals for this Tanaka item
View All Support Options Below
Free Tanaka TCS33EB16S manuals!
Problems with Tanaka TCS33EB16S?
Ask a Question
Free Tanaka TCS33EB16S manuals!
Problems with Tanaka TCS33EB16S?
Ask a Question
Popular Tanaka TCS33EB16S Manual Pages
Manual - Page 2
...chain saw service, other than the items listed in the instruction manual(s) maintenance instructions, should ...guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut above shoulder height. ○ Follow the manufacturer's sharpening and
maintenance instructions for two-handed use replacement bars and chains specified by competent chain saw service...
Manual - Page 4
...: device for enriching the fuel/air mixture
in contact with unit. Handling instructions: Included with a tree or log. 14. Recoil starter: Pull handle to be started or stopped.
4. Guide bar: The part that prevents the accidental operation of the engine housing. 7. Guide bar cover: Device for allowing the engine to start the engine. 6. Ignition...
Manual - Page 5
... before the unit is set down. ○ When... securely tightened.
○ Replace parts that are cracked, chipped...
WARNINGS AND SAFETY INSTRUCTIONS
Pay special attention to...instructions are not approved, could result in serious personal injury.
○ Using guide...or equipment damage, if instructions are tired, ill or...Replace damaged parts. Be aware of their hands and fi...
Manual - Page 7
...;.oz)
11.8 (350 ml)
Chain Oil Tank Capacity (fl.oz)
Dry Weight (lbs) (Without guide bar and chain)
Guide bar length (in.)
8.5 (250 ml)
8.4 (3.8 kg)
14 (350 mm)
16 (400 mm....8
Sprocket (number of chain
91VG / 91PX (Oregon)
Max. English
SPECIFICATIONS
○ Code "CS" of model name means "Chain saw"
Model
TCS33EB
Type of equipment
Chain saw, portable
Engine Size (cu. engine ...
Manual - Page 9
... will cause damage to get out of the groove in personal injury or property damage. Use of fuel with more than 10% ethanol may cause problems including overheating,
premature deterioration of oil. Always run the engine on your health or this unit. ○ The chain saw firmly with oil. Fueling...
Manual - Page 11
... properly. Operating level varies by setting the choke lever to the choked position.
... the front handle, hit the tip of the guide bar to a stump or a piece of wood...with the brake engaged, the clutch will overheat causing trouble. Please check to verify that chain oil is made ... engine. Before restarting the engine, ask our dealer for repairs. English
How to confirm the activation of the...
Manual - Page 12
.... Before felling a tree, carefully consider all specific situations, which it more than cutting down as...problems in -line with the bottom part of the guide bar. The safest cutting method is to cut with chain when cutting. Wind conditions. This will overheat causing trouble...of the tree. WARNING
Do not stand in your servicing dealer, forestry agent or local forestry schools for holes...
Manual - Page 18
...gauge to maintain original shape of the chain from the inside out. Part Number
91VG/91PX
2. Pitch 0.025" 3. Top plate 46. Cutting ... gauge setting found in the maintenance or operator manual for sharpening saw . (Fig. 48)
Fig. 48
General instructions for filing... Round off front corner to the specified setting. File Guide Angle
90°
18 English
45. Heel 50. Front...
Handling Instructions - Page 3
...guide bar and saw chain. 15. Guide bar cover: Device for enriching the fuel/air mixture in
contact with unit. Ignition switch: Device for stopping or locking
the chain. 13. Front handle: Support handle located at or towards the front of the throttle trigger until manually.... 5. Handling instructions: Included with a tree or log. 14. Guide bar: The part that prevents the...
Handling Instructions - Page 4
...'s manual, ...the unit is set down. ○...signaling a problem. Cutting safety...the saw service personnel. ...WARNINGS AND SAFETY INSTRUCTIONS
Operator safety &#...guide bar/chain other than recommended by the manufacturer which it is properly attached. ○ Keep others including children, animals, bystanders and helpers outside the hazard zone. Be aware of cutting area. Replace damaged parts...
Handling Instructions - Page 6
...(m/sec)
23.8
Sprocket (number of chain
91VG / 91PX (Oregon)
Max. SPECIFICATIONS
○ Code "CS" of model name means "Chain saw"
Model
TCS33EB / TCS33EB(S)
Type of equipment
Chain saw, portable
Engine Size (ml)
32... level (m/s2) by ISO 22867
Front handle
3.2
Rear handle
4.7
Uncertainty
0.8
Guide bar length (mm)
300
350
400
Type of teeth)
6
NOTE: Equivalent noise level/vibration levels ...
Handling Instructions - Page 9
...ask our dealer for inspection and repairs. To release the brake, pull... injure yourself severely. Consult your servicing dealer, forestry agent or local forestry...at high speed with the bottom part of the guide bar to fall in a nose... stumbling on specific woodcutting problems in terrain, vegetation, kind of... the reactive force will overheat causing trouble.
Please check to verify that it...
Handling Instructions - Page 12
...the electrodes are only for replacement. These factors cause deposits on the engine parts. ○ Abnormal fuel ... 32 Guide bar (Fig. 33) Before using a resistor spark plug to the machine. MAINTENANCE
MAINTENANCE, REPLACEMENT OR REPAIR OF THE...9675; Starting problems. ○ Engine power reduction. ○ Unnecessary wear on the spark plug electrodes, which may be replaced with the special...
Handling Instructions - Page 14
.... Toe 53. Always follow the recommended depth gauge setting found in injury.
58
Fig. 44
GENERAL INSTRUCTIONS FOR FILING CUTTERS File (60) cutter on forward stroke... GAUGES WITH A FILE
WARNING ○ Do not smoothen the upper part of cutter. (Fig. 47)
61
62
Fig. 47
59
Fig...and may result in the maintenance or operator manual for your cutters with a file or deform them. (Fig...
Handling Instructions - Page 15
...NON-ARMOR
160NDEA041 400 mm (16″) NON-ARMOR
120SDEA041 300 mm (12″) SPROCKET
MODEL NO. Part Number 2. Please exchange it for the new
one
when it can be securely fitted...64257;lter port in this instruction. NOTE When ordering the parts to
0.6 mm, or change the spark plug. ○ Clean the cooling fins on the parts breakdown section in the guide bar. ○ Clean ...
Tanaka TCS33EB16S Reviews
We have not received any reviews for Tanaka yet.