Tripp Lite B1262X2 Support and Manuals
Get Help and Manuals for this Tripp Lite item
This item is in your list!
View All Support Options Below
Free Tripp Lite B1262X2 manuals!
Problems with Tripp Lite B1262X2?
Ask a Question
Free Tripp Lite B1262X2 manuals!
Problems with Tripp Lite B1262X2?
Ask a Question
Popular Tripp Lite B1262X2 Manual Pages
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 1
...Models: B126-2X2, B126-4X4
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com/support
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com/support...tripplite.com/support
Copyright © 2017 Tripp Lite. You could also win an ISOBAR6ULTRA surge protector-a $100 value! Register your product for quicker service and ...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 2
... @ 60 Hz signal up to 75 ft. Output B126-4X4: 5V 3A) • 3.5 mm to
175 ft. IR Extension Cable (B126-4X4 Only) • Owner's Manual
Product Features
• Share multiple HDMI sources between multiple monitors • Route any input to any output, or route the same input to multiple outlets...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 3
...
• Switch between inputs via pushbuttons, remote control, or RS-232 serial • For model B126-4X4 only: Extend the remote control range, allow
discreet placement of four displays per channel ...; A 1080p @ 60 Hz signal can be extended up to 125 ft. no software or drivers required • Compatible with all operating systems • Compliant with the included five-foot IR extension...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 4
... port is
intended for the number of ports. 4.
Test to make sure that the entire installation works properly before pulling cables through ceilings/
walls. 2. 24 AWG, Solid Wire Cat5e/6 cable...-1A1 HDMI over Cat5 Receiver Unit, but the mounting hardware installation is required to the receiver unit for each mounting method. Installation will be the same for the
B126-4X4, except for ...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 6
.... If you have a B126-1P0, connect its built-in the installation.
11 Connect the remote receiver unit to a monitor using Terminal Emulation...2X2. Try each setting until an acceptable image is displayed.
15 Press the switch next to each set of the desired Output... step 9 for each additional remote receiver unit in this manual for each additional active remote receiver unit in HDMI connector...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 7
... IR extension cable to 125 ft. Position the cable's infrared sensor in an area that the entire installation works properly before pulling cables through ceilings/
walls. 2. 24 AWG, Solid Wire Cat5e/6 cable (such...
1 Make sure all devices being connected are turned off . Remote Repeater Installation
Notes: 1. Then connect the DB9 connector to the port on the switch. This port is required to ...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 8
...four displays (an active remote receiver should be the last unit in a channel). To finish your installation with a B126-1A0 or B126-1A0-WP-1 receiver, proceed to step 13.
10 Using Cat5e... to the repeater and plug it into a Tripp Lite Surge Protector, PDU or UPS. Remote Repeater Installation
5 Repeat step 4 to connect additional HDMI sources to the remaining ports.
6 Connect the external power...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 9
....
See the RS-232 Serial Control section in this manual for the B126-2X2. You can cause the monitor not... Tripp Lite Surge Protector, PDU, or UPS.
Remote Repeater Installation
13 Using Cat5e/6 cable, connect the RJ45 output port on ... units to adjust the video image. Note: An improper Equalization setting can also use the Equalization control on the receiver using Terminal Emulation...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 10
...-232 Serial Control, you must first access the Terminal Emulation Software and update the COM port settings. 1 Go to the Setup drop-down menu and select the Serial Port option.
2 Select the COM port that is being used, and update the remaining settings as follows: Baud Rate (57600), Data (8 bit), Parity (none), Stop (1 bit), Flow...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 11
The other settings can remain unchanged.
11
17-06-500-9333F8-EN.indd 11
7/10/2017 1:20:52 PM Receive (LF), Local Echo (enable). Go to allow input control. RS-232 Serial Control
3 Next, you will need to configure your software to the Setup drop-down menu and select the Terminal option.
4 Update the following settings;
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 12
Turns power to control the unit. RS-232 Serial Control
5 Once these settings are updated, the Terminal Emulation Software will recognize the switch, allowing you to enter commands to the switch on/off. The following table lists the available commands. ...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 13
... displayed.
4 What resolution are not able to get an acceptable image after adjusting the Equalization setting, try the following troubleshooting tips: 1 Are the external power supplies that support the video resolution you use cables that came with the product to adjust this manual for details on maximum distance and resolution when using must also...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 14
...trouble getting your Terminal Emulation Software to recognize the switch, check to make sure that it will occur, causing poor performance. Troubleshooting
6 Test your serial settings are set according to the instructions ... is loosened from the installation.
8 Check your cabling for any patch panels or other devices in the RS-232 Serial Control section of this manual.
14
17-06-500...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 15
... or television reception, which the receiver is limited to repairing or replacing (at its sole option) any way. EXCEPT AS ...digital device, pursuant to part 15 of the FCC Rules.
FCC Notice, Class B This device complies with the instructions, may not apply to...energy and, if not installed and used in materials and workmanship for help. To obtain service under this equipment not expressly...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 16
...notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
16
17-06-500 93-33F8_RevB
17-06-500-9333F8-EN.indd 16
7/10/... waste
WARNING Use of this equipment in life support applications where failure of this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide. Product specifications are entitled to:
• Send old equipment...
Tripp Lite B1262X2 Reviews
Do you have an experience with the Tripp Lite B1262X2 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Tripp Lite yet.
Earn 750 points for your review!