Tripp Lite B1264X4 Support and Manuals
Get Help and Manuals for this Tripp Lite item
View All Support Options Below
Free Tripp Lite B1264X4 manuals!
Problems with Tripp Lite B1264X4?
Ask a Question
Free Tripp Lite B1264X4 manuals!
Problems with Tripp Lite B1264X4?
Ask a Question
Popular Tripp Lite B1264X4 Manual Pages
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 1
... ISOBAR6ULTRA surge protector-a $100 value! Register your product for quicker service and ultimate peace of mind. Owner's Manual
HDMI Over Cat5 Matrix Switch
Models: B126-2X2, B126-4X4
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com/support
Ce manuel est disponible en français sur le...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 2
IR Extension Cable (B126-4X4 Only) • Owner's Manual
Product Features
• Share multiple HDMI sources between multiple monitors • Route any input to any output, or route the same input to multiple outlets ...remote receiver to extend a 1080p @ 60 Hz signal up to 75 ft. from the transmitter) • Use 24 AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite's N202-Series, to 175 ft.
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 4
...
B126-4X4, except for the B126-2X2 and B126-4X4. Test to make sure that the entire installation works properly before pulling cables through ceilings/
walls. 2. 24 AWG, Solid Wire Cat5e/6 cable (such as Tripp Lite's N202-Series) is required to the receiver unit for future use, and does not currently function.
4
17...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 5
... unit. at 1080p @ 60 Hz Up to DB9 adapter cable, insert the 3.5 mm connector into a Tripp Lite Surge Protector, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). When receiving power, the following ...1080i @ 60 Hz
Up to 175 ft. at 1080p @ 60 Hz Up to 50 ft. Standard Installation
Cable Box or DVR
Blu-ray™
Up to the 3.5 mm jack on the rear of sight between...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 6
... image should now be used for each additional active remote receiver unit in this manual for each set of the desired Output port to the active remote receiver unit, and plug it into a Tripp Lite Surge Protector, PDU or UPS. Standard Installation
8 Repeat step 7 to connect additional B126-Series remote receiver units to the remaining...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 7
... @ 60 Hz Up to 175 ft. Position the cable's infrared sensor in an area that the entire installation works properly before pulling cables through ceilings/
walls. 2. 24 AWG, Solid Wire Cat5e/6 cable (such as Tripp Lite's N202-Series) is
intended for the number of the unit. at 1080p @ 60 Hz
123
B126-110...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 8
.../2017 1:20:50 PM The Green Power LED and the Green RJ45 LEDs illuminate to the repeater and plug it into a Tripp Lite Surge Protector, PDU or UPS. To finish your installation with a B126-1A0 or B126-1A0-WP-1 receiver, proceed to step 13.
10 Using Cat5e/6 cable, connect the RJ45 output port...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 9
... RS-232 Serial Control section in this manual for details on the remote control of... B126-2X2 and B126-4X4. Remote Repeater Installation
13 Using Cat5e/6 cable, connect the RJ45...-WP-1 will illuminate.
Note: An improper Equalization setting can also use the Equalization control on the corresponding... remote receiver unit, and plug it into a Tripp Lite Surge Protector, PDU, or UPS. Note: The...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 10
...-232 Serial Control, you must first access the Terminal Emulation Software and update the COM port settings. 1 Go to the Setup drop-down menu and select the Serial Port option.
2 Select the COM port that is being used, and update the remaining settings as follows: Baud Rate (57600), Data (8 bit), Parity (none), Stop (1 bit), Flow...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 11
RS-232 Serial Control
3 Next, you will need to configure your software to the Setup drop-down menu and select the Terminal option.
4 Update the following settings; Go to allow input control. Receive (LF), Local Echo (enable). The other settings can remain unchanged.
11
17-06-500-9333F8-EN.indd 11
7/10/2017 1:20:52 PM
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 12
...:52 PM Turns power to control the unit.
For example, a command of sw1 A would display source A on /off. RS-232 Serial Control
5 Once these settings are updated, the Terminal Emulation Software will recognize the switch, allowing you to enter commands to the switch on output 1.
The following table lists the available commands.
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 13
... product
connected and plugged into a working power source? Try each setting until an acceptable image is displayed.
4 What resolution are you are the N022-01K-GY (Cat5) and N222-01K-GY bulk cables. Tripp Lite's HDMI over Cat5 extenders are tested to support up to work with 24 AWG solid wire, as are trying...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 14
... settings are having trouble getting your Terminal Emulation Software to recognize the switch, you are set according to the instructions in the RS-232 Serial Control section of this manual.... in between the transmitter, repeater, and receiver units? If you have occurred during installation. Tripp Lite's HDMI over Cat5 extender products were designed to be connected first; For Cat5e/6 ...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 15
... to TRIPP LITE or an authorized TRIPP LITE service center with the instructions, may not apply to operate this warranty, you must accept any way. This equipment generates, uses and can be determined by turning the equipment off and on a circuit different from TRIPP LITE or an authorized TRIPP LITE service center. Products must be accompanied by a brief description of the problem...
Owners Manual for HDMI Over Cat5 Matrix Switch English - Page 16
... or nitrous oxide. Tripp Lite has a policy of continuous improvement. Product specifications are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this equipment can reasonably be expected to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
16
17-06...
Tripp Lite B1264X4 Reviews
We have not received any reviews for Tripp Lite yet.