Tripp Lite PDU3EVN6L2130B Support and Manuals
Get Help and Manuals for this Tripp Lite item
This item is in your list!
View All Support Options Below
Free Tripp Lite PDU3EVN6L2130B manuals!
Problems with Tripp Lite PDU3EVN6L2130B?
Ask a Question
Free Tripp Lite PDU3EVN6L2130B manuals!
Problems with Tripp Lite PDU3EVN6L2130B?
Ask a Question
Popular Tripp Lite PDU3EVN6L2130B Manual Pages
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 1
... UPS System Shutdown Settings 3
2.3 SNMP Configuration
3
3. Command Line Interface
90
5.1 Syntax Conventions
90
5.2 Manual Pages
91
5.3 Output Conventions
91
5.4 Getting Started with your product for instructions on hardware installation and basic configuration, including IP address assignment. Troubleshooting
93
7. Register your Tripp Lite LX Platform device. Introduction...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 2
..., such as TeraTerm Pro by Ayera Technologies) Warning: Use of this equipment in life support applications where failure of the life support equipment or to the addresses you to : WEBCARDLX, WEBCARDLXS, PDU3E-series PDUs, PDU3XE-series PDUs and LX-suffix PDUs.
1.1 System Requirements
• Tripp Lite LX Platform Device • Ethernet network that enables remote...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 3
...System Shutdown Settings
When used with a Tripp Lite UPS during transmission, and that the Network Management System (NMS) communicating with your configuration requires a restart to take effect immediately so you restart PowerAlert Device Manager (or 'reboot' the LX Platform device). It can be loaded on loading a firmware or device driver upgrade, refer to enter a username/password hint...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 10
... time to enable or disable notifications for each of the event types. Use the sliders to apply your changes.
3. Use the dropdown menu in Mixed States
3.3.4 Control/Events
The Events page displays events supported by device model. Figure 3-13: Events Page
Figure 3-14: Setting Event Priority
10 The Web Interface
Figure 3-12: Load Group with...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 28
...any modifications. Note: The menu examples were generated using one operation. Tripp Lite
(c) Copyright 2005-2016
PowerAlert 15.00 (0-0001)...and will be found in one specific device model.
Because the content of many ...of the device-specific menus will vary based upon that the setting applies for all ...Some detail menus will immediately update the data as part of these are also ...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 63
...has Read/Write access to discover Tripp Lite SNMP devices on the network. The default password is not a program user.... and password may be changed from its default settings. The default password is same as the username. The default password is... It is the section of 2 RADIUS Servers that Tripp Lite's PowerAlert Network Shutdown Agent uses to all areas except to Main Menu
Refresh Menu
...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 71
...
: : 25 : :
Authentication Methods
Digest MD5 Authentication Supported: Yes
CRAM MD5 Authentication Supported : Yes
Login Authentication Supported
: Yes
Plain Authentication Supported
: Yes
Message Data From Address Subject
: [email protected] : PowerAlert Notification
1- Watchdog Settings X- Authentication Password 5- Remote Services M- Server Name 2- Port 3- Plain...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 79
...setting that come across the system. Acknowledge All Alarms This option gives the user the ability to Main Menu Refresh Menu
4.4.1 Alarms
This menu provides a summary of the active alarms. Any inactive, unacknowledged alarms will be removed as soon as such. The alarms acknowledged will be enabled if using with Tripp Lite...This is done.
This setting should be removed.
79...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 90
... at this document and the CLI error messages.
1. Mode Modifier - Directive - Command Line Interface
The LX Platform device firmware supports features on the command line interface. A program can 't describe your arguments. If the mode alone can usually perform several parts of the CLI output.
5.1 Syntax Conventions
The PowerAlert CLI uses its own standard syntax to...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 92
...Use the program 'devselect' to choose a device to work with factory default settings.
92 Use either 'hwclock' to change the network time settings. 2.
Use the program 'passwd' to set the password for any new non-SNMP account, which will assign it yourself. Use...angle brackets and the 'program name' replaced by the name of available programs? 1.
Use the program 'loadctl' to all alarms,...
Users Guide for WEBCARDLX PowerAlert Device Manager 9335A4 English - Page 93
.... Verify that they are still unable to perform the SNMP
set Check the SNMP settings of choice. See Section 3.4.3.1.3 for configuring actions.
7. Technical Support
Before contacting Tripp Lite Technical Support, refer to the following list of continuous improvement. Troubleshooting
If you encounter a problem: • Check all connections and confirm that you have added an SNMP...
Owner s Manual for 3-Phase Switched 0U Power Distribution Units 93349E Multi-language - Page 1
....com/support Copyright © 2017 Tripp Lite.
Register your product for quicker service and ultimate peace of mind. a $100 value!
All rights reserved. 1
16-06-273-93349E.indb 1
2/16/2017 3:34:16 PM
You could also win an ISOBAR6ULTRA surge protector- Owner's Manual
3-Phase Switched 0U Power
Distribution Units
(Phase, Bank and Outlet Measurements)
208V MODEL...
Owner s Manual for 3-Phase Switched 0U Power Distribution Units 93349E Multi-language - Page 11
... ports.
**Only 2 of four different Tripp Lite EnviroSense2 (E2)
A3
environmental sensors* for 20 seconds to restore the PDU's network interface to remove the plug and insert from the receptacle. To unplug equipment properly, use the pull tabs to its factory default settings. C20 Plug-Lock Inserts (Optional): Use the included C20 plug-lock inserts...
Owner s Manual for 3-Phase Switched 0U Power Distribution Units 93349E Multi-language - Page 12
... service problem does not originate from Tripp Lite. Instead, visit www.tripplite.com/support.
3. A variety of Extended Warranty and On-Site Service Programs are also available from a misreading of the package. The RMA number, along with shipping instructions will ask for your product for service, follow these steps:
1. Review the installation and operation procedures in this manual...
Owner s Manual for 3-Phase Switched 0U Power Distribution Units 93349E Multi-language - Page 13
... all applicable instructions, to jurisdiction).
If the product should not be free from original defects in its sole discretion. Seller will repair or replace the product, in material and workmanship for a period of 2 years from Tripp Lite they are designed to register your Tripp Lite product has been assigned a unique series number. This Warranty gives you specific legal...
Tripp Lite PDU3EVN6L2130B Reviews
Do you have an experience with the Tripp Lite PDU3EVN6L2130B that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Tripp Lite yet.
Earn 750 points for your review!