Duct Silencer - Installation Instructions
Page 1
.... For this application the VSIL10 should be done by using hanging straps or framing. 3. Item# 450512 Rev. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY...The VSIL10 may be used to damage elec- 2. The VSIL10 may be mounted at the range hood. Again the VSIL10 may also be in either direction. 2. Date: 061908 DIMENSIONS - The VSIL10 is intended for residen- 3. The VSIL10 must be located between the fan outlet and the roof cap ...
.... For this application the VSIL10 should be done by using hanging straps or framing. 3. Item# 450512 Rev. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY...The VSIL10 may be used to damage elec- 2. The VSIL10 may be mounted at the range hood. Again the VSIL10 may also be in either direction. 2. Date: 061908 DIMENSIONS - The VSIL10 is intended for residen- 3. The VSIL10 must be located between the fan outlet and the roof cap ...
Installation Instructions
Page 20
... cover or soffit Wall cap Duct Hood Wall installation exterior power typical ductwork Duct cover or soffit Hood NOTE: Wall exhaust must be hard wired direct with 2-wire with ground. Electrical Supply Run 120 VAC electrical wiring from ground. Adjust your hood on local codes and geographic location. Proper installation of...
... cover or soffit Wall cap Duct Hood Wall installation exterior power typical ductwork Duct cover or soffit Hood NOTE: Wall exhaust must be hard wired direct with 2-wire with ground. Electrical Supply Run 120 VAC electrical wiring from ground. Adjust your hood on local codes and geographic location. Proper installation of...
Installation Instructions
Page 26
... vary by using a locally supplied trim. limit. A1 Attach duct cover to ceiling. Drill holes in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to step 3) NOTE: It is recommended to follow option A or B, however both aren't necessary. Push filter rear up , then...
... vary by using a locally supplied trim. limit. A1 Attach duct cover to ceiling. Drill holes in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to step 3) NOTE: It is recommended to follow option A or B, however both aren't necessary. Push filter rear up , then...
Specs
Page 4
..." (25.4 cm) Max. hoods. Use a qualified and trained installer. it creates back pressure/air turbulence and greatly reduces performance. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with longer duct runs. ventilator kit rating) PLUMBING Not applicable Note: All CFMs are best; Amps Interior Exterior 4.9/7.4 7.4/4.7 4.9/7.4 7.4/4.7/5.5 8.2 5.5/6.2 8.2 5.5/6.2 3.9 6.6/3.9 4.7 7.4/4.8/5.5 8.6 5.6/6.4 9.5 6.5/7.3 4.7 8.6 4.7 7.4/4.7/5.5 8.6 5.6/6.4 * A 1,200 CFM interior- or...
..." (25.4 cm) Max. hoods. Use a qualified and trained installer. it creates back pressure/air turbulence and greatly reduces performance. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with longer duct runs. ventilator kit rating) PLUMBING Not applicable Note: All CFMs are best; Amps Interior Exterior 4.9/7.4 7.4/4.7 4.9/7.4 7.4/4.7/5.5 8.2 5.5/6.2 8.2 5.5/6.2 3.9 6.6/3.9 4.7 7.4/4.8/5.5 8.6 5.6/6.4 9.5 6.5/7.3 4.7 8.6 4.7 7.4/4.7/5.5 8.6 5.6/6.4 * A 1,200 CFM interior- or...