Owner Manual
Page 6
.../antenna ■ Two four-button transmitters ■ The red status LED indicator light ■ A push-button Valet button ■ Your warranty registration ■ A shut-down toggle switch Important Information Congratulations on the purchase of your system, you will maximize the use of this system, it must be installed by an authorized dealer...
.../antenna ■ Two four-button transmitters ■ The red status LED indicator light ■ A push-button Valet button ■ Your warranty registration ■ A shut-down toggle switch Important Information Congratulations on the purchase of your system, you will maximize the use of this system, it must be installed by an authorized dealer...
Owner Manual
Page 10
... its intended mode of operation may result in accordance with the keys in the product installation guide. This testing should be disabled using the installed toggle switch. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO...
... its intended mode of operation may result in accordance with the keys in the product installation guide. This testing should be disabled using the installed toggle switch. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO...
Owner Manual
Page 16
... is in the ON position, the engine will shut down inputs: ■ The brake pedal is pressed. ■ The hood is opened. ■ The shutdown toggle switch is put into the OFF position. ■ The pre-programmed run time (12, 24, or 60 minutes) has elapsed. ■ Transmitter button is remote started...
... is in the ON position, the engine will shut down inputs: ■ The brake pedal is pressed. ■ The hood is opened. ■ The shutdown toggle switch is put into the OFF position. ■ The pre-programmed run time (12, 24, or 60 minutes) has elapsed. ■ Transmitter button is remote started...
Owner Manual
Page 20
... stored in a location of your choice. Starter Anti-Grind Circuitry Whenever the vehicle is remote started accidentally. LOCATION OF SHUTDOWN SWITCH © 2005 Directed Electronics-all rights reserved 17 NOTE: Anti-grind circuitry only works when the remote start system is operating... System This feature allows your installer for recommended locations. To disable the remote start, move the shutdown toggle switch to the start position during remote start position. The switch can be temporarily disabled to prevent the vehicle from engaging, even if the key is installed.
... stored in a location of your choice. Starter Anti-Grind Circuitry Whenever the vehicle is remote started accidentally. LOCATION OF SHUTDOWN SWITCH © 2005 Directed Electronics-all rights reserved 17 NOTE: Anti-grind circuitry only works when the remote start system is operating... System This feature allows your installer for recommended locations. To disable the remote start, move the shutdown toggle switch to the start position during remote start position. The switch can be temporarily disabled to prevent the vehicle from engaging, even if the key is installed.
Owner Manual
Page 28
... 1.5 seconds. Remove your remote ■ To disarm the system press for one second. Turn the ignition back off when exiting Valet Mode. Location of Shutdown Switch © 2005 Directed Electronics-all rights reserved 25 Disabling the Failsafe® Starter Kill without a transmitter ■ Turn on (if connected) and the vehicle will... leave the engine running. The LED will flash once to confirm arming. The LED will stop flashing and the vehicle should start , move the shutdown toggle switch to the "ON" position.
... 1.5 seconds. Remove your remote ■ To disarm the system press for one second. Turn the ignition back off when exiting Valet Mode. Location of Shutdown Switch © 2005 Directed Electronics-all rights reserved 25 Disabling the Failsafe® Starter Kill without a transmitter ■ Turn on (if connected) and the vehicle will... leave the engine running. The LED will flash once to confirm arming. The LED will stop flashing and the vehicle should start , move the shutdown toggle switch to the "ON" position.
