Viper Responder 350 Support and Manuals
Get Help and Manuals for this Viper item
View All Support Options Below
Free Viper Responder 350 manuals!
Problems with Viper Responder 350?
Ask a Question
Free Viper Responder 350 manuals!
Problems with Viper Responder 350?
Ask a Question
Most Recent Viper Responder 350 Questions
Disarming Security System
How do you override the Viper security system if the transmitter is very old and inoperable?Codes on...
How do you override the Viper security system if the transmitter is very old and inoperable?Codes on...
(Posted by Ponchdawson 7 years ago)
Viper Responder 350 Videos
Viper 350 Plus and Viper Responder 350
Duration: :46
Total Views: 29,348
Duration: :46
Total Views: 29,348
Popular Viper Responder 350 Manual Pages
Owner Manual - Page 2
...INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS... neglect, improper service, installation or other causes...repair or replace with a comparable reconditioned model any unit with a legible copy of the bill of sale or other dated proof of purchase bearing the following conditions are met: the unit was originally installed...
Owner Manual - Page 3
... name and address ➤ Type of alarm installed ➤ Year, make, model and color of the automobile ➤ Automobile license number ➤ Vehicle identification number ➤ All security options installed on how long an implied warranty will last or the exclusion or limitation of the plan or call Directed Customer Service at 1-800876-0800. and hereby...
Owner Manual - Page 4
... information 4
System maintenance 5 FCC/ID notice 6 Replacement remote controls 7 2-way LCD remote control functions 7 Standard configurations (1-way and 2-way remote controls 7 Standard LCD icon configurations (2-way only 9 Remote operation 12 System signal paging features 12 Out of range notification 13 Programming LCD remote 14 To enter programming mode 14 Beeps/Vibration On/Off 14...
Owner Manual - Page 9
... ready circuitry
(may require additional labor) ➤ 548T receiver/antenna
Important information
Congratulations on the purchase of your system.
Installation of this system, it prior to get the most out of your state-of this product by an authorized dealer only. This owner's guide should help you to using the system.
4
© 2008...
Owner Manual - Page 15
... ignition icon will display for full alarm by flashing for vibrator notification (see programming LCD remote section of the guide). Icon
The vibrate icon will always display if the remote is programmed for a few seconds and then display continuously until page is cleared. Icon
The trunk icon will display for full alarm by flashing for a few seconds and...
Owner Manual - Page 16
After clearing the page, press and release the program button until the vehicle number is shown. Icon
The arm icon will display for full alarm by flashing for vehicle number 2, the remote will flash when the system is unlocking the doors and display continuously until the system is disarmed.
© 2008 directed electronics
11
For...
Owner Manual - Page 17
..., but may also be customized by an authorized dealer. The buttons described in this manual correspond to the remote control as confirmation of receipt of a command or alarm system status. Command Page
When a command (arm/disarm, or auxiliary channel) from the remote control is the signal the control module sends to a Standard Configuration transmitter. When...
Owner Manual - Page 18
... clear future repeats of the page notification. The remote will beep and or vibrate every 60 seconds to receive the command, the remote responds with 3 set to the incorrect vehicle or is beyond the range of 4 rapid beeps (shock, trunk, door, ignition, or hood trigger) and the LCD icon that the alarm system was triggered and...
Owner Manual - Page 20
... vehicle. door unlocked, engine started, vehicle violation, etc.). The LCD backlight will be notified to the remote.
Note: If programmed Off, no alarms will illuminate when a remote button is pressed, or an alarm status page is page Off. When programmed off the remote will exit programming mode after 5seconds of a page (audibly beeping if the vehicle's status changes, e.g.
Owner Manual - Page 21
... this manual correspond to the standard configuration. If you will be checked.
Remember, this guide. The LCD remote responds to ...remote for additional details.
➜ Active arming
You can be set up. Using your system
The buttons described in -vehicle's status LED will flash approximately once per second, indicating that the system is called Bypass Notification. See your installer...
Owner Manual - Page 26
...five times) within 15 seconds. If the system does not disarm, you to disarm the security system without the remote transmitter should it be programmed to respond to one to five pulses of the
and triggered zone icons.
© 2008 directed electronics.... In order to disarm the system. Be sure to check with the installer for the location and the number of presses of Pulses
important!
Owner Manual - Page 31
for 1.5
Channel 3 auxiliary output: When connected, pressing and will respond with a page notification consisting of the Auxiliary outputs.
26
© 2008 directed electronics Consult your dealer for available options for 4 seconds displays the channel number on the LCD screen.
This occurs at the remote after the system has received the command to control an...
Owner Manual - Page 36
... possible to four users of the system have different settings that transmitter. Using the Directed Bitwriter®, a hand-held programming tool, your vehicle, one for each transmitter that is used , the system will automatically re-sync and respond to that meet their specific needs. Then, whenever a specific transmitter is a feature available exclusively from Directed. Check...
Owner Manual - Page 38
... the remote). The following is turned off : With
this feature on , and the doors are closed, and unlock when the ignition is a list of the program settings, with the factory settings in ... However, some may require additional installation labor. Ignition lock and unlock are independent features and can be in the programming grid to lock when the security system passively arms (after the ...
Owner Manual - Page 40
... may cause your installer is programming the security system with the Directed Bitwriter, the full triggered response can be programmed off : When the system is armed and a door is considered a nuisance. note: Because many states have laws regulating how long a security system can be programmed for a complete explanation of times. note: This feature will respond to inputs...
Viper Responder 350 Reviews
We have not received any reviews for Viper yet.