Ventilation Specification
Page 4
... sections of -0.1" (-2.5 mm) water column (vacuum) when measured at the connection to the dryer. 4 Heat In order to remove moisture from the washer. Connect each dryer in the system. ■ A minimum back pressure of these codes may be considered in the design of any central exhaust system:...: ■ The capacity to handle up to 230 CFM (cubic feet per minute) of dryer vent systems. Whirlpool does not design multidryer vent systems, nor does Whirlpool review or provide approvals for vent systems designed by third-party engineering firms. Outside Exhaust The four basic reasons for...
... sections of -0.1" (-2.5 mm) water column (vacuum) when measured at the connection to the dryer. 4 Heat In order to remove moisture from the washer. Connect each dryer in the system. ■ A minimum back pressure of these codes may be considered in the design of any central exhaust system:...: ■ The capacity to handle up to 230 CFM (cubic feet per minute) of dryer vent systems. Whirlpool does not design multidryer vent systems, nor does Whirlpool review or provide approvals for vent systems designed by third-party engineering firms. Outside Exhaust The four basic reasons for...
Ventilation Specification
Page 5
of the exhaust vent. The maximum airflow is recommended to dissipate heat. Codes Agency Approvals All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and combo washer/dryer units that have an inlet and outlet for wall, door, and floor moldings. ■ Additional... spacing of 1" (25 mm) on all sides of any Whirlpool produced dryer at connection to 30 ft [9.1 m]). Side view...
of the exhaust vent. The maximum airflow is recommended to dissipate heat. Codes Agency Approvals All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and combo washer/dryer units that have an inlet and outlet for wall, door, and floor moldings. ■ Additional... spacing of 1" (25 mm) on all sides of any Whirlpool produced dryer at connection to 30 ft [9.1 m]). Side view...
Ventilation Specification
Page 6
... 1"* (25 mm) "AF" Code Certain electronic dryer models have your vent may have a blocked or partially blocked vent or that have a washer and dryer on the control panel. To resolve this issue: ■ Check to see if the vent run cleaned. For multi-dryer venting systems,... (310 cm2) 3"* (76 mm) Multiple Dryer Venting Systems Multiple dryer venting systems must be consulted for recessed or closet installation, with stacked washer and dryer 48 in many apartment buildings. A. Individual dryer exhaust - Listed here are required. Each dryer is too long. Weighted dampers C. If...
... 1"* (25 mm) "AF" Code Certain electronic dryer models have your vent may have a blocked or partially blocked vent or that have a washer and dryer on the control panel. To resolve this issue: ■ Check to see if the vent run cleaned. For multi-dryer venting systems,... (310 cm2) 3"* (76 mm) Multiple Dryer Venting Systems Multiple dryer venting systems must be consulted for recessed or closet installation, with stacked washer and dryer 48 in many apartment buildings. A. Individual dryer exhaust - Listed here are required. Each dryer is too long. Weighted dampers C. If...
Installation Guide
Page 3
... and compound (for your "Use and Care Guide" for information about accessories available for installing new exhaust vent) 2' (0.6 m) inlet hose 5' (1.52 m) inlet hose and rubber washer Additional parts may be at least 4 ft. (1.22 m) long.
... and compound (for your "Use and Care Guide" for information about accessories available for installing new exhaust vent) 2' (0.6 m) inlet hose 5' (1.52 m) inlet hose and rubber washer Additional parts may be at least 4 ft. (1.22 m) long.
Installation Guide
Page 4
.... Side view: Back view: NOTE: Most installations require a minimum of 20 - 120 psi (138 - 827 kPa). Lower temperatures may use the water supply for your washer using the "Y" connector and short hose (if needed) which are required. Space must be exposed to shut off at least 18" (460 mm) above floor...
.... Side view: Back view: NOTE: Most installations require a minimum of 20 - 120 psi (138 - 827 kPa). Lower temperatures may use the water supply for your washer using the "Y" connector and short hose (if needed) which are required. Space must be exposed to shut off at least 18" (460 mm) above floor...
Installation Guide
Page 15
...duct tape, screws, or other side of hose failure. Screw on coupling by hand until it is seated on connector. 3. Remove old rubber washer from inlet hose and replace with additional two-thirds turn . Use clamps to exhaust hood 2. Attach short hose and "Y" connector Vent must ...be connected to the "Y" connector. Attach washer cold inlet hose to exhaust hood with 4" (102 mm) clamp. Secure vent to other fastening devices that extend into interior of vent to reduce...
...duct tape, screws, or other side of hose failure. Screw on coupling by hand until it is seated on connector. 3. Remove old rubber washer from inlet hose and replace with additional two-thirds turn . Use clamps to exhaust hood 2. Attach short hose and "Y" connector Vent must ...be connected to the "Y" connector. Attach washer cold inlet hose to exhaust hood with 4" (102 mm) clamp. Secure vent to other fastening devices that extend into interior of vent to reduce...
Use & Care Guide
Page 4
... dryer to be installed on options and ordering, call 1-800-807-6777 or visit us at: www.whirlpool.com/accessories. ACCESSORIES Enhance your new washer and dryer with the following genuine Whirlpool accessories. In Canada, call 1-800-901-2042, or visit us at a premium, the stack kit allows the dryer to a more information...
... dryer to be installed on options and ordering, call 1-800-807-6777 or visit us at: www.whirlpool.com/accessories. ACCESSORIES Enhance your new washer and dryer with the following genuine Whirlpool accessories. In Canada, call 1-800-901-2042, or visit us at a premium, the stack kit allows the dryer to a more information...