Whirlpool WRT518SZK Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WRT518SZK manuals!
Problems with Whirlpool WRT518SZK?
Ask a Question
Free Whirlpool WRT518SZK manuals!
Problems with Whirlpool WRT518SZK?
Ask a Question
Popular Whirlpool WRT518SZK Manual Pages
Installation Instructions - Page 2
... THE WATER SUPPLY 17 FINAL INSTALLATION 19
Installing the access cover and forming the copper tubing 19 Connecting the power/leveling the unit 20 STARTING THE ICE MAKER 21 TROUBLESHOOTING 22 Operational notes 22 Troubleshooting chart 22 The modular ice maker service sheet 23 Ice maker replacement parts list 24 Ice maker replacement parts list (cont'd 25
Requesting Assistance...
Installation Instructions - Page 4
... set of a specific step you are contained in the illustration.
4 Hand drill with any tools listed here. 1. A DETAIL shows a close-up illustration of a certain portion of a diagram or an illustration of steps shown, refer to install a part, position the part as shown in bubbles alongside the larger illustration. Tubing cutter 10. Read and follow the instructions...
Installation Instructions - Page 5
... the valve. IMPORTANT: When you account for the Ice Maker, a replacement parts list is provided on a table where they can be easily identified and located.
The KEY numbers correspond to 18 Cubic Foot Top Freezer Models.
*** For installation in 11 Cubic Foot Top Freezer Models only (kit 24ECKMF). 5 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15...
Installation Instructions - Page 6
... holder (if necessary, refer to install the ice maker. Set these areas
Rear wall
Rear wall
Power cord plug and receptacle
Power cord plug and receptacle
Power cord plug and receptacle
Top freezer model
Bottom freezer model
Side-by -side units, you have to support the ice bucket. On top-mount models without a full-width freezer...
Installation Instructions - Page 10
... screws.
1⁄2" hex-head sheet-metal screws
Refer to the side diagrams for models with the screw you removed earlier (see DETAIL A).
Fill tube
Spout
Foam gasket
Installing the fill tube/gasket (14 to 18 cubic foot and Bottom Freezer models)
DETAIL A
2. Insert the fill tube through the hole in the back cover...
Installation Instructions - Page 11
... at the approximate locations shown in DETAIL C and DETAIL D (for 11 Cubic Foot Top Freezer Models with Fill Tube and Bracket Fill Tube).
DETAIL C Alternate fill tube
design
DETAIL D Fill... cover, then remove the cover and set it aside. Installing the tubing clips
Refer to page 12. Peel the backing from rear access cover DETAIL A Installing the tubing clips
11
If you have...
Installation Instructions - Page 15
...connector (remove and discard)
Wiring harness connector
Installing the ice maker clips
15 Remove and discard the blank connector from the cup. For Side-By-Side Models Only: Refer to DETAIL A and mount ...with two 3⁄4" hex-head sheet-metal screws. You will fit through this cutout when you install the ice maker. Mounting the ice maker
Refer to the side diagram for the following step....
Installation Instructions - Page 16
... raised tab). Center the top tabs under clips
Insert fill tube into place (you installed earlier.
Position the ice maker inside the freezer compartment and connect its top and bottom mounting...of the ice maker to the wiring harness connector so they lock).
4. For Side-By-Side Models Only: Position the ice maker so that its wiring connector to the freezer liner mounting hole with...
Installation Instructions - Page 18
...Connect to Refrigerator Follow the connection instructions specific to the rear panel with the copper tubing. Do not overtighten.
Copper tubing
C. Secure copper tubing to your model. 1.
Avoid kinks when coiling the...back of copper tubing to allow the refrigerator to refrigerator and check for service. Bend the copper tubing to the valve inlet using the original screw in the panel...
Installation Instructions - Page 20
.... If it is crooked and needs to 18 Cubic Foot Top Freezer Models)
Sheet-metal screw (for 11 Cubic Foot Top Freezer Models only)
Leveling the ice maker
20 Place a level on top of the...you need to re-level the refrigerator, follow the procedure to follow these instructions can result in your refrigerator's "Use and Care Guide."
3. Do not remove ground prong.
Do not use an extension cord....
Installation Instructions - Page 21
...models without a full-width freezer shelf, you will not function properly if the ice bucket is placed directly on top of the inverted ice tray shelf. Installing... freezer wall (see the side diagram) to "Troubleshooting" on 21
After that it
Turning the ice ...problems, refer to its "on top of the freezer shelf. The ice maker will be gone. This completes the installation...
Installation Instructions - Page 22
... Ice tastes stale. Troubleshooting chart
The following sounds is being dumped into the ice bucket (see page 21); PROBLEM One or more ice, adjust the freezer control for a colder setting. Not enough ice... or if you use a well as a water source, you encounter problems with your service center should consider installing a second water strainer in Ice Maker overflows. CAUSE The water valve is...
Installation Instructions - Page 23
... RETAINING CLIPS WITH BIMETAL. FILL CUP REMOVE MODULE, MOTOR, AND SUPPORT ASSEMBLY. PULL FILL CUP FROM MOLD.
WHEN REINSTALLING EJECTOR BLADES, REALIGN "D" COUPLING WITH MODEL CAM.
MOTOR - 1.5 WATTS, 8800 OHMS MODULE -
LOOSEN BOTH SCREWS. ADDITIONAL ROTATION COULD DAMAGE MODULE. REINSERT TO FULL DEPTH.
Specifications
MOLD HEATER - 185 WATTS, 72 OHMS THERMOSTAT - DISCONNECT SHUT...
Installation Instructions - Page 24
... 16 17 18 19 20 21 22 23
Part Number 628228 628356 627843 627788 627790 627796 627985 489322 628358 628258 489136 489276 627792 628256 2155021 489128 1115846 628366 627929 1115844 628229 628379
Description Mold and Heater Assembly Bearing and Inlet Ejector Ice Stripper Support Retainer, Thermostat (2) Thermostat (also Order #542369 Cement Alumilastic...
Installation Instructions - Page 25
Ice maker replacement parts list (cont'd)
The following parts are not included in this list. Part Number 939529 837142 1121997 *836489 *1106508 *488645 *488649 *841707 *627854... Cubic Foot Top Freezer Models) Screw, 8 x 1/2" Screw, 8-32 x 1/2" Insert, Plastic Tube Tube Assembly, Inlet Valve Nut, Inlet Valve Washer Dampener Tube Clamp Tube Clamp Tube Clamp Clamp, Service Cord Plastic Tube Nut ...
Whirlpool WRT518SZK Reviews
We have not received any reviews for Whirlpool yet.