Owner's Manual
Page 3
..., meets FCC requirements. The unit should be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by following measures: Relocate either this product or the device that provides guidelines for proper grounding and, in wire to an antenna ...protection against voltage surges and built-up static charges. Article 810 of interference, which can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. Modifications not expressly approved by the manufacturer or have the same ...
..., meets FCC requirements. The unit should be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by following measures: Relocate either this product or the device that provides guidelines for proper grounding and, in wire to an antenna ...protection against voltage surges and built-up static charges. Article 810 of interference, which can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. Modifications not expressly approved by the manufacturer or have the same ...
Owner's Manual
Page 31
..., press ENTER to return to the RESULT:EXIT screen. SL SR . PREPARATION p ■ If a warning screen appears 1 Press ENTER to display detailed information about potential problems detected during auto setup. Notes • If you change the SUBWOOFER PHASE parameter in the SETMENU (see page 29. Press j / i to switch between warning messages.
..., press ENTER to return to the RESULT:EXIT screen. SL SR . PREPARATION p ■ If a warning screen appears 1 Press ENTER to display detailed information about potential problems detected during auto setup. Notes • If you change the SUBWOOFER PHASE parameter in the SETMENU (see page 29. Press j / i to switch between warning messages.
Owner's Manual
Page 33
... / -). • Use speakers of similar quality and efficiency. • If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again. • If warning W-1 appears, corrections are connected correctly. • Check the speaker connections for ...appear depending on the speakers even when the speakers are made . • If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center. PREPARATION 29 AUTO SETUP Warnings after auto setup Press j / i to the listening position. • Check the speaker connections for ...
... / -). • Use speakers of similar quality and efficiency. • If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again. • If warning W-1 appears, corrections are connected correctly. • Check the speaker connections for ...appear depending on the speakers even when the speakers are made . • If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center. PREPARATION 29 AUTO SETUP Warnings after auto setup Press j / i to the listening position. • Check the speaker connections for ...
Owner's Manual
Page 97
...is set to OFF, and no video signal is currently being received from a source component, such as lightning or strong static electricity). If the problem persists, the cables may be reproduced by this unit. Disconnect the optimizer microphone. Refer to always show the OSD. The setting for the on... chart below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to turn on when STANDBY/ ON (or SYSTEM POWER) is pressed, or enters the standby mode soon after...
...is set to OFF, and no video signal is currently being received from a source component, such as lightning or strong static electricity). If the problem persists, the cables may be reproduced by this unit. Disconnect the optimizer microphone. Refer to always show the OSD. The setting for the on... chart below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to turn on when STANDBY/ ON (or SYSTEM POWER) is pressed, or enters the standby mode soon after...
Owner's Manual
Page 98
...set to minimum. NONE, the surround back speaker setting is Raise the level of the center speaker is automatically set to NONE. TROUBLESHOOTING Problem The sound suddenly goes off. Only the speaker on the power, and play the source again. - No sound from the subwoofer. No...selector setting is set to minimum. Press MUTE to the center channel, and the front and surround speakers output effect sounds. If the problem persists, 12 the cables may be heard. Incorrect balance settings in SUR. Adjust the SPEAKER LEVEL settings. 66 When playing a monaural ...
...set to minimum. NONE, the surround back speaker setting is Raise the level of the center speaker is automatically set to NONE. TROUBLESHOOTING Problem The sound suddenly goes off. Only the speaker on the power, and play the source again. - No sound from the subwoofer. No...selector setting is set to minimum. Press MUTE to the center channel, and the front and surround speakers output effect sounds. If the problem persists, 12 the cables may be heard. Incorrect balance settings in SUR. Adjust the SPEAKER LEVEL settings. 66 When playing a monaural ...
Owner's Manual
Page 99
sources cannot be defective. Firmly connect the audio plugs. If the problem - persists, the cables may be output Dolby Digital or DTS digital instructions for your turnable to the 19 GND terminal. an MC-head amplifier. It ... should be recorded. GND terminal of this unit is turned off. can be recorded by a digital recording component connected to this DIGITAL OUTPUT jack. TROUBLESHOOTING Problem Cause Remedy Refer to page Dolby Digital or DTS The connected component is not connected to Connect the source component to the analog AUDIO this...
sources cannot be defective. Firmly connect the audio plugs. If the problem - persists, the cables may be output Dolby Digital or DTS digital instructions for your turnable to the 19 GND terminal. an MC-head amplifier. It ... should be recorded. GND terminal of this unit is turned off. can be recorded by a digital recording component connected to this DIGITAL OUTPUT jack. TROUBLESHOOTING Problem Cause Remedy Refer to page Dolby Digital or DTS The connected component is not connected to Connect the source component to the analog AUDIO this...
Owner's Manual
Page 100
...all noise. There is noise when the OSD is multipath interference. Move this unit further away from digital or radio frequency equipment, or this problem when the transmitter is too far away or the antenna input is poor. The OSD may cause this unit. Select OFF in with the ... 40 - 21 40 40 - 40 - - 96 Cause The characteristics of FM stereo broadcasts may be tuned in . Refer to page - 71 - ■ Tuner Problem FM stereo reception is noisy. This unit suddenly turns into the standby mode. Cause Remedy This unit is too close to eliminate multipath interference. There...
...all noise. There is noise when the OSD is multipath interference. Move this unit further away from digital or radio frequency equipment, or this problem when the transmitter is too far away or the antenna input is poor. The OSD may cause this unit. Select OFF in with the ... 40 - 21 40 40 - 40 - - 96 Cause The characteristics of FM stereo broadcasts may be tuned in . Refer to page - 71 - ■ Tuner Problem FM stereo reception is noisy. This unit suddenly turns into the standby mode. Cause Remedy This unit is too close to eliminate multipath interference. There...
Owner's Manual
Page 101
.... axis from an Reposition this unit. - The signal coding or modulation of 6 m (20 ft) and no more than 30 degrees off- ■ Remote control TROUBLESHOOTING Problem The remote control does not work nor function properly. The remote control does not "learn" new functions. The distance between the two remote Place the...
.... axis from an Reposition this unit. - The signal coding or modulation of 6 m (20 ft) and no more than 30 degrees off- ■ Remote control TROUBLESHOOTING Problem The remote control does not work nor function properly. The remote control does not "learn" new functions. The distance between the two remote Place the...