Zenith SL-6201 - Heath - Wireless Pushbutton Support and Manuals
Get Help and Manuals for this Zenith item
This item is in your list!
View All Support Options Below
Free Zenith SL-6201 manuals!
Problems with Zenith SL-6201?
Ask a Question
Free Zenith SL-6201 manuals!
Problems with Zenith SL-6201?
Ask a Question
Popular Zenith SL-6201 Manual Pages
User Guide - Page 1
... with existing Heath®/Zenith jumper or
dip switch systems.
• Patented Technology
• Battery powered push button - Select models
only (see Lighted Push Bar Feature for more than one chime
system in the same house.
• Factory installed batteries.
• LED halo lighted push bar -
No wires to run.
• 128 selectable codes allow...
User Guide - Page 2
...screwdriver. See Code and Tune
batteries
Setting section.
3. Press push button to activate
the chime receiver code. Use either screws or double sided tape to mount push button.
• To mount with screws, remove back of case to activate
factory installed batteries.
... Up
Remove material in screw hole. 1. If chime does not sound, see Troubleshooting.
4.
Mount push button.
User Guide - Page 3
... the same for setting the code.
4.
Code and Tune Settings
Code Settings
Note: Most installations will not require you to expand your chime and push button. WARNING: Disconnect chime unit from power source before reconnecting to see if system is factory set; however, there are used for both the push button and chime.
Follow the instructions below for this...
User Guide - Page 4
... switch low (0 or OFF). This tune can be changed by following the instructions below.
• Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes) Push Button: Location 8, Remove jumper or set dip switch low (0 or OFF). Chime: Remove jumper from location 8.
• Westminster (Eight note...
User Guide - Page 5
... for instruction)
Back of Chime
Note: Some models might require the use of batteries.
598-1105-06
-- Inside Push Button
ON 1234 5678
12345678
* Code Settings 1-7 Must Match Both Push
Button and Chime
Tune Setting (Not used on all models)
Tune Setting
Insert Batteries (+) Positive Side Up
C
R 122
0+
(+) Positive Battery Terminal
Replacing Push Button Batteries
Most Models: Install...
User Guide - Page 6
...8
12345678
Tune Setting (Not used on all models)
* Code Settings 1-7 Must Match Both Push
Button and Chime
Tune Setting
(+) Positive Battery Terminal
CR 2032
Insert Batteries (+) Positive Side Up
Replacing Push Button Batteries
Model 6444: Install two lithium type CR2032 3 volt batteries positive (+) side up.
--
598-1105-06 Open access door (see chime manual
for instruction)
Back of Chime...
User Guide - Page 7
Halo Lighted Push Bar Feature (Select Models Only)
This Heath®/Zenith wireless push button contains a LED (Light Emitting Diode) that will illuminate in photocontrol will allow the light intensity of the push button will indicate its setting. Decals on the specific mounting environment of the push button. The actual time and intensity that include two...
User Guide - Page 8
...not work when installed: • Do not mount chime or push button on metal or near metal studs. The range of push button and chime batteries (if applicable), replace
if necessary. ...button off metal surface. • Concrete floors may reduce range. Troubleshooting
Chime does not sound: • Make sure push button and chime codes are the same (See pages 3
through 6). • Check ...
User Guide - Page 9
...guide.
You may cause undesired operation.
If you experience a problem, follow this Product
Lifetime Finish Warranty
(Selected Models Only)
Full Lifetime Finish (plate only) warranty to the following information available: Model... AM to operate the equipment. You may also write* to store. No Service Parts Available for regulatory compliance could void the user's authority to 4:30 PM CST...
User Guide - Page 10
... to you. Please keep your dated sales receipt, it is required for inconvenience, installation, setup time, loss of any malfunction caused by this warranty in previously sold products.
-...requests. Repair service, adjustment and calibration due to you specific legal rights. REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF ...
Zenith SL-6201 Reviews
Do you have an experience with the Zenith SL-6201 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Zenith yet.
Earn 750 points for your review!