Home » Beltronics » Radar Detectors & Jammers » Beltronics Vector 995

Beltronics Vector 995 Support Question

Find answers below for this question about Beltronics Vector 995.
Need a Beltronics Vector 995 manual? We have 1 online manual for this item!

Beltronics Overview Questions Manuals Reviews Videos Research

Question posted by Tani995 on August 24th, 2021

Whenever I Power On The Vector 995 It Keep On Running The Same Message

is it possible to upgrade the device ??

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on August 25th, 2021 12:14 AM

SonuKumar

Member since:
May 9th, 2021

Points: 16,617,810

100
points

https://www.beltronics.com/register/beltronics_eula.asp

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Beltronics Vector 995 Manual Pages

Owner's Manual - Page 2

... starting with Display (Pilot), then Voice (Voice), then Power-On sequence (PwrOn), then Signal Strength Meter (Meter), and.... The buttons labeled CITY and BRT are also used a radar detector before, a review of the Quick Reference Guide on pages ...). Programming Details ̈ The V995 will provide a "Reset" message, accompanied by holding both CITY and BRT buttons down for 2 seconds...

Owner's Manual - Page 3

...Press the RVW button to go from one category to the next PILOT (Power-on indication) VOICE POWER-ON SEQUENCE SIGNAL STRENGTH METER AUTOMUTE CITY MODE SENSITIVITY BANDS * Factory Default ... • Interpreting Alerts • How Radar Works • How "POP" Works • How Laser Works • TSR Signal Ranking Software • How Safety Radar Works Service • Troubleshooting • ...

Owner's Manual - Page 4

...mount V995 directly behind the vehicle. Page 11 Note: In the Dark Mode the display will indicate radar band, and a precise bar graph of signal strength. Brightness Button Press to fully understand V995's operation... these simple steps 1 Plug the small end of the power cord into the side jack of the detector, and plug the large end of the power cord into your car's lighter socket. 2 Mount your ...

Owner's Manual - Page 5

...slides over the lighter plug. To ensure that might obstruct the radar antenna or laser lens. Caution! Optional power cords See the Accessories section for unobtrusive and hassle-free mounting.... (there are available. 6 7 Note: Depending on your vehicle, the lighter socket power may require the optional European sleeve to determine if your windshield. Windshield QuickMount V995's ...

Owner's Manual - Page 6

...silence the audio alert during a radar encounter. You can select alternate power-on indication After V995's start-up and down, accompanied by a bar-graph on , a safety radar message will not show Highway, AutoScan...tell you to indicate which sensitivity mode is turned on the display. Power-on displays. If Safety Radar (SWS) is selected. See the Programming section for details. If...

Owner's Manual - Page 7

...;cation. In this new level of information about detected signals. 11 A complete listing of the text messages is detected, only the audio will display the actual numeric frequency of the radar signal being encountered. Power Connector V995's power jack uses a telephone-type connector. This 4-conductor connector only works with this mode, V995 will be...

Owner's Manual - Page 8

... from one category to the next PILOT (Power-on indication) VOICE POWER-ON SEQUENCE SIGNAL STRENGTH METER AUTOMUTE CITY MODE... AutoMute to scroll through all categories, it will provide a "Reset" message, accompanied by holding both the CITY and BRT buttons down . Press... V995's display will begin again at the top of the detector, and are highlighted in more bands are disabled Turn bands ...

Owner's Manual - Page 9

...you put V995 in "AutoScan" or "Highway" modes. 15 Power-on ) In this setting, V995 will be heard when a radar, Laser, or SWS message is also followed by an audible alert. "X OFF"), will ...signal strength. (factory default) MeterTEC (Tech Display meter) In this setting, all radar, laser, and SWS messages (if programmed) will reduce X-band alarms from X-band intrusion alarms and motion ...

Owner's Manual - Page 10

... • Ku-band 13.400 GHZ ± 25MHz • Laser 904nm, 33 MHz bandwidth Radar Receiver / Detector Type • Superheterodyne, VTO • Scanning Frequency Discriminator • Digital Signal Processing (DSP) ...setting all North American radar and laser frequencies are no trafﬁc radar units using that you with an audible alert, and associated text message stating which band has ...

Owner's Manual - Page 11

...handbook is as complete as we can be taken seriously. V995 emits short alerts for radar, laser and safety alerts. These signals may be set up nearby. 19 Because ...intermittently. V995 gives an X-band, or K-band alert intermittently. Explanation You are approaching a continuous radar source aimed in frequency. Such alerts should be dangerous. You are typically not as strong or...

Owner's Manual - Page 12

... typically use LIDAR equipment parallel to cosine error (an inaccuracy, which increases as conventional radar, therefore, you become familiar with distance. AS A RESULT, EVEN THE BRIEFEST LASER ALERT... alarms and motion sensors often operate on the power of the radar equipment itself. LIDAR uses these being that your V995's radar detection abilities are limitations to decide which target is...

Owner's Manual - Page 13

... SWS safety radar system has 64 possible messages (60 currently allocated). Our new proprietary software (TSR), intelligently sorts, ranks and rejects this new feature, please give us a call or visit our website for more prevalent (the number of operating transmitters is ready to start protecting you to it unnecessarily. The SWS messages your detector is...

Owner's Manual - Page 14

... within range of the Programming options. Contact Beltronics for V995 to decode the speciﬁc safety message (page 22-23) Self Cal V995 is not behind tinted areas. • Determine if your... may not have radar or laser unit turned on . • Check that the power is ON. • Check that vehicle ignition is ON. • Check that the laser lens is running a self-calibration ...

Owner's Manual - Page 15

... you did not purchase your V995. 26 Register online: @ www. Product Purchased Vector 995 Radar & Laser Detector Serial Number 3. Enclose the following information with a Service Order Number, which must... have a question 2. It may be contacted with a quotation. Ship V995 and power cord to: BELTRONICS Customer Service Department Service Order Number 5442 West Chester Road West ...

Owner's Manual - Page 16

... warranty covers: BELTRONICS warrants your protection) to the extent they violate the laws of any of the original purchase receipt. 3. Standard Coiled Power Cord.........$14.00 Direct-wire Power Cord 10.00 Coiled SmartPlug 29.95 Direct-wire SmartPlug 29.95 Accessory Kit 19.95 Extra Windshield Mount 4.00 Features, speciﬁ...