Black & Decker LST201 Support Question
Black & Decker LST201 Support Question
Find answers below for this question about Black & Decker LST201.Need a Black & Decker LST201 manual? We have 1 online manual for this item!
Question posted by grantgiles on August 24th, 2021
Line Won't Advance
The bump feed on my lst201 weed eater doesn't workIt appears to be stuck or not advancing the lin
Current Answers
Answer #1: Posted by SonuKumar on August 24th, 2021 9:13 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,673,760
Member since:
May 9th, 2021 Points: 16,673,760
Why is my Black and Decker not feeding line?
Jammed Line
The most common cause of the Black and Decker Trimmer auto feed not working is a jammed line, which happens within the spool. ... The spare line from Black and Decker has a specific diameter, so this can also cause the line to jam if the size does not fit the spool.
https://trimthatweed.com/black-and-decker-trimmer-auto-feed-not-working/
The line of a Weed Eater trimmer head won't advance if it is too short because not enough centrifugal force acts on it. ... Running the trimmer with line that is 50 percent or less of the recommended length can cause the head to turn too quickly, which can wear out the engine.
https://homeguides.sfgate.com/line-weed-eater-keep-getting-stuck-96906.html
https://trimthatweed.com/black-and-decker-trimmer-auto-feed-not-working/
https://www.ehow.com/info_7873549_black-feeding-line-not-working.html
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Black & Decker LST201 Manual Pages
Instruction Manual - Page 1
...; Do not bump the feed head against the ground - INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. otherwise the appliance will disrupt the feed mechanism. • For use only .065 inch diameter ROUND line
(B+D Model #AF-100 is 20 volts.
20V MAX* STRING TRIMMER
INSTRUCTION MANUAL
CATALOG NUMBER
LST201
Thank you...
Instruction Manual - Page 2
...,
may result in death or serious injury. Important Safety Warnings WARNING: When using electric
gardening appliances, basic safety precautions should be caught in a dry, locked-up place out of... spectacles or goggles at a safe distance from work going away from oil and grease. • CHECK DAMAGED PARTS - Don't use , when replacing line, or prior to solid objects and where
necessary...
Instruction Manual - Page 3
... be shorted by this manual. • DO NOT immerse appliance in water or squirt it with a pressure washer. • Keep guards in place and in working order. • Keep hands and feet away from chemically treated lumber To reduce your appliance may burst causing personal injury and damage. SYMBOLS The label...
Instruction Manual - Page 4
... center when service or repair is cracked or damaged, do not place battery in locations where the temperature may cause respiratory irritation. Take it to work together. • These chargers are burned.
• Do not charge or use the appliance and battery pack in aprons, pockets,
4 take it to clean. WARNING...
Instruction Manual - Page 6
... liquid. INSTALLING AND REMOVING THE BATTERY PACK FROM THE APPLIANCE
WARNING: Make certain the lock-off
button is installed, remove
11
the covering from the line cut-off blade, located on the edge of the guard
E
6
Make sure the tabs (13) on until an audible click is heard (Figure B). D
B
10
11...
Instruction Manual - Page 7
... as shown in figure G3. G
G1
5
5O-10O
G2
G3
RELEASING THE CUTTING LINE
In transit, the cutting line is achieved, tighten the collar by loosening the collar (5) and rotating it opposite of the...and slowly
swing the trimmer side to the spool housing. CAUTION: Inspect area to obtain proper working positions shown in figure G.
7 CONVERT TO EDGING MODE
WARNING: When being used as an
...
Instruction Manual - Page 8
... appropriate hole in the spool housing. L
CUTTING LINE / LINE FEEDING Your trimmer uses .065 inch (1.65 mm) diameter, ROUND nylon line. • Lift the edge guide (7) into the edging position as shown in Figure I
surfaces or heavier weeds are being cut;
The advanced automatic line feeding mechanism senses when more feeding if the cutting or edging is the best...
Instruction Manual - Page 9
...com.
REPLACEMENT ACCESSORIES CAUTION: Before you begin trimming,
only use serrated or heavier gauge line, as described in this appliance could be hazardous. Do not use the appropriate type ... the new spool and push it onto
the boss (19) (figure N) in the housing. The line should protrude approximately 5-3/8 inches (136mm) from becoming trapped under the spool.
• Align the spool...
Instruction Manual - Page 10
...line...line is recommended you periodically touch-up the sharpness of the cutting line...line reaches the recesses (23), cut the line. (figure P).
• Fit the spool onto the appliance as shown in layers. Your trimmer line...
21
2. The line cutter on ,...line into one or more of the line...line in top condition, store spare pre-wound spools or bulk line...Wind the cutting line onto the spool...the line on...
Instruction Manual - Page 12
... (0.065 inch (1.65 mm)) - Imported by Black & Decker (U.S.) Inc.,
701 E. If damaged, replace spool. • Pull the cutting line until it snaps securely into the housing. If the automatic line feed still does not work or the spool is maintained. • Ensure you are not exceeding a 10° angle as detailed in the spool...
Similar Questions
Does The Gh3000 Have A Spring Under The Spool Of Line
(Posted by Anonymous-174520 10 months ago)
Unable To Locate Proper Spool Cover For Lst201 Type 3.
can't find anyone carrying spool cover for a lst201 type3. Can you help or give a part number?
can't find anyone carrying spool cover for a lst201 type3. Can you help or give a part number?
(Posted by Ritinv 2 years ago)
My Lst201 Trimmer Quit While Trimming Grass By My Fence. The Line Was Barely Out
of the spool. I recharged the battery but got no response. The trimmer was 2 years old in May. Any t...
of the spool. I recharged the battery but got no response. The trimmer was 2 years old in May. Any t...
(Posted by rustycannon1 4 years ago)