Boss Audio PH2.1000 Support Question
Boss Audio PH2.1000 Support Question
Find answers below for this question about Boss Audio PH2.1000.Need a Boss Audio PH2.1000 manual? We have 1 online manual for this item!
Question posted by Anonymous-128644 on January 13th, 2014
Amp And Sub
why does this amp not work with a 1200 watt 4 ohm boss sub
Current Answers
Related Boss Audio PH2.1000 Manual Pages
User Manual in English - Page 1
...PH2.500 PH2.600 PH2.800 PH2.1000 PH2.1300 PH2.1500
Two Channel MOSFET Car Audio Amplifiers
PH4.400 PH4.500 PH4.600 PH4.700
Four Channel MOSFET Car Audio Amplifiers
PH1500M PH2500M
MonoBlock MOSFET Car Audio Amplifiers
Congratulations on your choice for making your purchase of listening pleasure.
USER'S MANUAL
page CONTENTS
2 Introduction 2 What is included? 3 Features 3 About 2 Ohm...
User Manual in English - Page 2
... system of your input source. What is missing, contact the store where you integrate the amp into your system regardless of the nature of controls in these amplifiers in order to help you purchased the amplifier.
• PHANTOM amplifier
• Remote subwoofer level control
•High input cable with the remote level control module...
User Manual in English - Page 3
Features
Your new PHANTOM amplifier features the following:
• Class A-B operation
• Bridgeable outputs (except PH1500M and PH2500M)
• Tri-Mode capable (except PH1500M and PH2500M)
• MOSFET PWM (Pulse Width Modulated) Power Supply
• 2 Ohm stable stereo operation with output power increase
• Thermal and speaker short protection
• Soft turn-on circuit...
User Manual in English - Page 4
...amplifier to mount the amplifier.
2.
If the mounting surface is turned off while connecting the input jacks and speaker terminals.
Place the amplifier in your car's...or damage to the amplifier, do not permit any of the amp's mounting holes, to install it. Never operate the amplifier when it only ...work near the gas tank, fuel lines, hydraulic lines and electrical wiring.
User Manual in English - Page 5
... to the "BATT+" connection on the head unit to about 3/4 volume, and adjust the amplifier's input level control(s) to the amplifier, and excessive audio distortion. Further fine tuning of the car.
Ignoring these instructions will result in length. If multiple amplifiers are being used ) using 16 gauge (or heavier) wire.
3. Insert fuse(s) into the...
User Manual in English - Page 6
... level and low level inputs from your receiver to your amplifier at the same time!
2-Channel Amplifiers
PH2.500, PH2.600, PH2.800, PH2.1000, PH2.1300, and PH2.1500
Remote Subwoofer Level Control
R
POWER
RL
HIGH LEVEL ...OSF ET POWE R AMPL IFIER
To Audio Outputs of head
unit or signal processor
4-Channel Amplifiers
PH4.400, PH4.500, PH4.600 and PH4.700
Remote Subwoofer Level Control
CH3/4 CH1...
User Manual in English - Page 7
MonoBlock Amplifier
PH1500M and PH2500M
Remote Subwoofer Level Control
R
POWER
R
L
HIGH LEVEL INPUTS
LOW INPUTS
L
2V-8V 100mV-2V
...
M OSF E T M ONOBL OCK POWE R AM PL I FI E R
To Audio Outputs of head
unit or signal processor
PHANTOM MOSFET Amplifier User's Manual - Always use a high-quality RCA cable for best audio performance. NOTE: Do not connect BOTH the high level and low level...
User Manual in English - Page 8
...receiver to your head unit lacks RCA outputs. L- L+
To Speaker Terminals of head unit
4-Channel Amplifiers
PH4.400, PH4.500, PH4.600 and PH4.700
CH CH CH CH
4+ 4- 3- ...
The high level input(s) should only be used when your amplifier at the same time!
2-Channel Amplifiers
PH2.500, PH2.600, PH2.800, PH2.1000, PH2.1300, and PH2.1500
Remote Subwoofer Level Control
R
POWER
R
L
HIGH LEVEL...
User Manual in English - Page 9
MonoBlock Amplifier
PH1500M and PH2500M
R
POWER
R
L
HIGH LEVEL INPUTS
LOW INPUTS
L
2V-8V 100mV-2V
min
max
INPUT... of head unit
Remote Subwoofer Level Control
PHANTOM MOSFET Amplifier User's Manual - L+
To Speaker Terminals of the amplifier. High Level Input Wiring
The high level input(s) should only be used when your amplifier at the same time! Be sure to observe polarity...
User Manual in English - Page 10
... Channel and Bridged Modes
2-Channel Amplifiers PH2.500, PH2.600, PH2.800, PH2.1000, PH2.1300, and PH2.1500
Two
Channel Mode
+
LEFT
- Subwoofer
SPEAKER IMPEDANCE
4-8 OHMS
L
R
SPEAKER CONNECTIONS BRIDGED MODE
FUSES
Connect the Positive (+) terminal of head unit
FUSE
Battery
+ -
Speaker
+ - RIGHT Speaker
SPEAKER IMPEDANCE
2-8 OHMS
L
R
SPEAKER CONNECTIONS BRIDGED MODE
Bridged...
User Manual in English - Page 11
...OHMS
Chassis ground point
to REMOTE TURN-ON terminal of this mode, put the crossover switches in MONO. Be sure to check the table at the bottom of head unit
FUSE
Battery
PHANTOM MOSFET Amplifier User's Manual - The main speakers will operate in STEREO... Amplifiers
Tri-Mode
PH2.500, PH2.600, PH2.800,
PH2.1000, PH2.1300, and PH2.1500
Tri-mode operation allows you wish to achieve.
User Manual in English - Page 12
... REMOTE TURN-ON terminal of the LEFT subwoofer to the CH3 (+) amplifier terminal.
PHANTOM MOSFET Amplifier User's Manual -
CH1
CH2
SPEAKER CONNECTIONS
BRIDGED MODE
CH3
CH4
SPEAKER CONNECTIONS
BRIDGED MODE
+12V
GND
FUSES
REMOTE
POWER CONNECTIONS
Bridged Mode
LEFT Subwoofer
SPEAKER IMPEDANCE
4-8 OHMS
Connect the Negative (-) terminal of head unit
FUSE
Battery Connect...
User Manual in English - Page 13
... the wiring as shown below. page 13 The main speakers will operate in STEREO while the subwoofer simultaneously operates in this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. Tri-Mode
SPEAKER IMPEDANCE
8 OHMS
Component values for the crossover frequency you to connect this mode, put the...
User Manual in English - Page 14
SPEAKER IMPEDANCE
2-8 OHMS
SPEAKER CONNECTIONS
FUSES
+12V
GND
REMOTE
POWER CONNECTIONS
Chassis ground point
to REMOTE TURN-ON terminal of head unit
FUSE
Battery
PHANTOM MOSFET Amplifier User's Manual - page 14 Power and Speaker Wiring
MonoBlock Mode
MonoBlock Amplifiers PH1500M and PH2500M
MonoBlock Mode
+
Speaker
-
User Manual in English - Page 15
... make sure you experience operation or performance problems with this point, go on until the faulty/noisy component is found.
It is set the amplifier's input level control as low as possible. Check for the amp model is at least 3VDC. Check that the Remote Input (Turn-On) has at least 12v.
Similar Questions
Amp Is Being Weird
Amp will turn on when ignition is turned off, it will stay on for a few seconds then turn off, when ...
Amp will turn on when ignition is turned off, it will stay on for a few seconds then turn off, when ...
(Posted by bryntone17 2 years ago)
Placed New Battery In Car And Connected All Wiring, Amp And Speakers Not On
(Posted by Anonymous-169351 2 years ago)
Why Does My Ph2.1000 Get So Hot.
I just changed subs. From a Alpine 12"dvc 4ohm to a fosgate t1 12" dvc 4ohm. Now my ph2.1000 gets so...
I just changed subs. From a Alpine 12"dvc 4ohm to a fosgate t1 12" dvc 4ohm. Now my ph2.1000 gets so...
(Posted by jfarnsworth100 2 years ago)
How To Set Up Speakers With Sub To The Amp.
I have a 12 sub and 2 6s speakers and I dont know how to hook them up and but have only bass thru th...
I have a 12 sub and 2 6s speakers and I dont know how to hook them up and but have only bass thru th...
(Posted by Rileyahill11 3 years ago)