Craftsman 21400 Support Question
Craftsman 21400 Support Question
Find answers below for this question about Craftsman 21400 - 10 in. Band Saw.Need a Craftsman 21400 manual? We have 1 online manual for this item!
Question posted by dtaylor717 on April 22nd, 2016
Zts 6000 Mower Dies When Try To Lower/raise Deck Or Engage Blades.
I have a ZTS 6000 zero turn craftsman mower. When I try to move deck or engage blades the mower dies. I have checked the seat safety switch, checked the inline belreaker, replaced the switch for the mower deck raise/lower, and also replaced the PTO engage switch. Not sure where to go from here. Hoping you can help
Current Answers
Answer #1: Posted by Odin on April 22nd, 2016 9:39 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,670
Member since:
April 10th, 2010 Points: 41,236,670
See http://bit.ly/1WhqtGL. If that doesn't solve, consider the other links at http://bit.ly/1WhqsCG.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Craftsman 21400 Manual Pages
Owners Manual - Page 1
www.craftsman.com Owner's Manual
10-in. BANDSAW
1/3 HP MOTOR Model 119.214000
CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions.
• Table of Contents
• Full One Year Warranty • Safety Instructions • Assembly • Getting to Know Your Bandsaw • Adjustment • Operation •...
Owners Manual - Page 2
...! If this warranty will apply for commercial or rental purposes, this tool is equipped with padlocks, master switches, or by removing starter keys.
@
Never operate a tool while under the influence of drugs, medication, or alcohol.
Table of contents ...
2
Full one year warranty ...
2
Safety instructions ...
2
Assembly...
4
Getting to know your work area well lighted and...
Owners Manual - Page 3
... parts should immediately be properly repaired or replaced.
_PECIAL SAFETY RULES FOR BANDSAWS
1. Always turn off the machine if the material is to saw will operate properly and perform its intended function. Make sure that appear on Tools. Note and follow the safety warnings and instructions that the blade tension and blade tracking are properly adjusted. 8, Make "relief...
Owners Manual - Page 4
...lower table trunion with washer in one box. Assemble the upper table trunnion to the table. 1.
Use any packing material.
Prior to make sure all parts from the bag of the table (See Fig. 1). a. Medium Screwdriver 1
Adjustable Wrench t
Square 1
LIST OF LOOSE PARTS IN BAG
Item
Description
Q'ty. UNPACKING AND CHECKING... CONTENTS
Model 119.214000 10"...saw blade...
Owners Manual - Page 5
... is recommended that when in the machine's base. (See Fig. 5)
FIG. 2
c.
To ensure sufficient upright stability of the machine it should be
bolted to the saw blade. The bandsaw has a 2-1/2" dust port included. (Sea Fig. 6) It is connected to a suitable dust collector. b. FIG. 6
tension knob =g knob
]uide
T
_. _
_Blade
rack ng knob
'Guide...
Owners Manual - Page 6
...
NOTE: Do not adjust the fence handle such that the indicator reads
zero degree on the lower table trunnion and place a suitably sized square against the saw blade and the table for trunnion, recheck the saw blade.(See Fig.8)
FIG. 10
b. To avoid injury to the saw blade position.
2.
After counterclockwise truning the fence handle, sliding the rip fence...
Owners Manual - Page 7
... the new saw blade ensure the blade teeth are approximately 1/16" behind the gullets of the saw blade tracking by turning the upper wheel by unlocking the guide adjusting screw (B) Fig. 15
d. Re-tension the new saw blade and check the saw blade. The saw blade should be just clear of the back of the saw blade, proceed as mentioned below" TRACKING THE SAW BLADE" h. g. Replace the rip...
Owners Manual - Page 8
..., usually in use water or other operation control, a safety device or the power cord, turn the workpiece without pushing it from the center of the ...seated correctly before starting check if any part of dust. Remove the old drive belt and fit the new belt. (ensure ribs in contact with the saw blade tension. Select the right saw blade to cut to prevent it , as the motor switch...
Owners Manual - Page 9
... or defective bearing. 2. Defective switch. 3 Defective motor.
1. The blade has come off the motor, tighten the blade tension knob. 2. The saw blade correctly. Remedy
1. Open the doors and check.
3. Replace the blade. 4. Fit the saw blade has broken. 4.
Diagnosis
1. Replace the lock switch. 3. Put light pressure on . Adjust the blade guides (see ADJUSTMENT instructions...
Owners Manual - Page 11
...Ball Bearing 12ram Retaining Ring 28 Lower Wheel Tire
Retaining Ring 12 Saw Blade Upper Wheel
Upper Bearing Bolt Wheel ...Blade Tracking Knob Cap
Blade Tracking Knob Body Hex. Nut M14
Motor PuUey Hex. Nut M6
Cable w/Plug Lock Washer 4 Washer 4
Pan Head Screw M4x8 Switch Cover Plate Lock Switch...Fence Carrier
Head Screw M6x1O
,Special Screw Washer 10 Fence Handle Roll Pin 3x18
Star knob screw...
Owners Manual - Page 20
... major brand appliances, lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it -yourself. For the replacement parts, accessories and owner's manuals that you need to do-it ! For Sears professional installation of home appliances and items like vacuums, lawn equipment, and...
Similar Questions
Utility Pump Needs Replaced Day 4 No Help Sears All Shut Down Lowes No Help Ohio
submersible utility pump needs replaced day 4 and still no help ,,I went to 3 different lowes they w...
submersible utility pump needs replaced day 4 and still no help ,,I went to 3 different lowes they w...
(Posted by tabathacosta20 2 years ago)
Left Blade On My Craftsman Lt 2000 18.5 Horsepower Mower Came Loose I Retightene
the left blade on my craftsman 2000 lt mower came loose i retightened it as soon as i turned it on i...
the left blade on my craftsman 2000 lt mower came loose i retightened it as soon as i turned it on i...
(Posted by elbert64jw 8 years ago)
Engine Replacement For A 1955 Craftsman 131.8250.
I have an old craftsman lawn mower 1955, MN 131.8250 and would like to replace the engine. The old o...
I have an old craftsman lawn mower 1955, MN 131.8250 and would like to replace the engine. The old o...
(Posted by jkinney6 8 years ago)
How To Replace New Return Spring On 42' Craftsman Mower Deck?
I have a 15.5 h.p craftsman tractor model number 917529550 and can't find any info on how to replace...
I have a 15.5 h.p craftsman tractor model number 917529550 and can't find any info on how to replace...
(Posted by edesloover1 8 years ago)
Manual For My Craftsman 9' Band Saw
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
(Posted by glorioussuhn37 11 years ago)