Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by lwardynah on June 24th, 2014
How To Change The Clock Time On A Power Connect 6248
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 6248 Manual Pages
Command Line Interface Guide - Page 58
Power Over Ethernet (PoE)
Configures PoE and displays PoE information. RMON
Can be configured through the CLI and displays RMON information.
Clock
Configures the system clock....and Image Manages the switch configuration files.
SSH
Configures SSH authentication.
58
Command Groups Line
Configures the console, SSH, and remote Telnet
connection. Management ACL
Configures...
Command Line Interface Guide - Page 628
... Mode Interface Configuration (Ethernet) mode
User Guidelines Change the default value of this command only to 30 seconds. Time in Interface Configuration mode to set to adjust ... The actual timeout is this parameter or the product of the Radius transmission times the Radius timeout, whichever is set the time that the switch should wait for a response to
an EAP-request frame from the client ...
Command Line Interface Guide - Page 629
... example sets the time for the retransmission of an EAP-request frame to the client to 30 seconds. Command Mode Interface Configuration (Ethernet) mode
User Guidelines Change the default value... resending the request. Syntax dot1x timeout tx-period seconds no form of seconds that the switch should wait for a response to an Extensible Authentication Protocol (EAP)-request/identity frame from ...
Command Line Interface Guide - Page 630
This feature is an extension of seconds that the switch waits for a response to an EAP-request/identity frame to 3600 seconds... a number when RADIUS indicates the Tunnel-Private-Group-ID for the specified interface. Syntax show dot1x command in Power Connect Release 2.1. Command Mode Privileged EXEC mode
User Guidelines This command has no default configuration.
A valid Ethernet interface....
Command Line Interface Guide - Page 635
...representing the identity of Dot1x Option 81 feature added in the display:
Field Interface Username
Supp MAC Address Session Time Filter-ID
VLAN Assigned
Description
The port number. This field shows the username when the port control is .... VLAN Assigned 1
The following table describes the significant fields shown in Power Connect Release 2.1. Specifies a valid interface number.
User's Guide - Page 5
Power Connection 53
4 Hardware Description
Overview 55 Front Panel 56 Rear Panel 59 Console (RS-232) Port 61 Physical Dimensions 61 Power Supplies 62 ...
5 Configuring Dell PowerConnect
Overview 71 Starting the CLI 72 General Configuration Information 74
Terminal Connection Configuration 74 Baud Rate 74 Other Configuration Requirements 74 Booting the Switch 75 Configuration Overview 81...
User's Guide - Page 21
...be captured across the entire network.
Trivial File Transfer Protocol (TFTP) The PowerConnect 6200 Series switches support boot image, firmware, and configuration upload or download through TFTP. Simple..., examined, and acted upon.
SNTP The Simple Network Time Protocol (SNTP) assures accurate network switch clock time synchronization up to common industry practice. For more information ...
User's Guide - Page 49
... interfaces and provides information about cable connections. Stations are connected to the switch's ports through the physical interface ports on the front panel. The topics covered in this section include: • Ethernet Interface • SFP Interfaces • Bay 1 and Bay 2 Interfaces • Serial Cable Connection • Power Connection
Cable and Port Information
49 For each...
User's Guide - Page 61
... an EIA/TIA-232 port.
If you connect the terminal to a subordinate switch, you need to assemble and cable the stack before powering up for management through a serial interface.
This port provides a direct connection to the switch and is used only for the first time, the switches elect a Master Switch, which may occupy any location in the stack...
User's Guide - Page 62
... PowerConnect 6248 has four fans. Repeat this process until all of the switch rear. Create a stack by observing the LEDs. See Figure 4-13.
1. For each of the switches in the stack, connect one of the top switch and the switch directly below it. Install a separately purchased stacking module in rear "Bay 1" of each switch in the stack.
2. Power Supplies...
User's Guide - Page 74
... Configuration Requirements The following is required for downloading embedded software and configuring the switch: • ASCII terminal (or emulation) connected to the serial port (cross-cable) in the rear of the unit • Assigned IP address for the switch for changing the default baud rate using CLI commands:
console#configure
console(config)#line console...
User's Guide - Page 75
... disk check on with the local terminal already connected, the switch goes through Power On Self Test (POST). POST messages are displayed on the switch. Ensure that the serial cable is loaded into RAM. Device details... Booting the Switch
When the power is an example of simultaneously open files: 22
Configuring Dell PowerConnect
75 Select an option.
User's Guide - Page 105
... The following components are required for the purpose of switch when powered up - Using the RS-232 port, connect the switch to establish a remote network management connection with the default configuration and definitions. which is the configuration of this example: • PowerConnect 6200 Series switch • A workstation with the following components installed:
- See "Device...
User's Guide - Page 111
... Ethernet ports, or through a
network connected to reload the stack? (y/n) y
Reloading all switches..
Enabling Remote Management 1. Device Default ...Dell PowerConnect
111 Enter the enable command at the privileged mode prompt (#), and reboot the device. console>
console>enable
console#delete startup-config
Startup file was deleted
console#reload
Management switch has unsaved changes.
Once...
User's Guide - Page 213
...connected to the switch through a captive portal. To disconnect all clients from all authenticated clients that are connected through the captive portal, click System → Captive Portal →Client Connection...MAC address of the connected client. • Protocol...connection protocol, which is sorted by client MAC address.
To view information about the clients connected to the switch...
User's Guide - Page 214
... IP address of the connected client. • Interface - Shows the current connection protocol, which is either HTTP or HTTPS. • Session Time - Shows the amount of time that are authenticated to a specific interface. Shows the current account type, which is Guest, Local, or RADIUS. To view status information
for clients connected to view clients that...
User's Guide - Page 317
... Ports menu page contains links to configure Flow Control. Restores the switch operation to auto.
Since ports set for ports configured as storm control and port mirroring, and for switches that are directly connected.
The default value is incompatible with head of time, and is defined for performing virtual port tests. This command affects...
Getting Started Guide - Page 9
... 5 cm (2 inches)
on each location marked on the bottom of power, connect the 12 VDC power cable from a (separately purchased) PowerConnect RPS-600 for non-PoE switches or PowerConnect EPS-470 for other end of the RS-232 crossover cable to a grounded AC outlet at this time. The surface must be able to use the CLI. The...
Getting Started Guide - Page 266
...port counters show stack-port diag show switch
show supported switchtype
LED
LED Dell Power Connect PC6248P ,PC6224P ,PC6248 , PC6224ו.PC6224F -
PowerConnect 6200
PC 6224
1-1
PC 6248
2-1
...
Release Notes - Page 5
...-stop forwarding. All file types which may be used for a supplicant.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Added Functionality in this Release ¾ Non-Stop Forwarding
This feature creates an option to allow the stacking and CX-4 plug-in Power Connect Release 2.1 to accept a VLAN name as an alternative to a number when...
Similar Questions
How To Change The Clock On A Power Connect 6248
(Posted by KeEmmym 9 years ago)
How To Get To Boot Menu On Power Connect 6248 Switch
(Posted by weedchandr 10 years ago)
