Dewalt DW734 Support Question
Dewalt DW734 Support Question
Find answers below for this question about Dewalt DW734.Need a Dewalt DW734 manual? We have 2 online manuals for this item!
Question posted by mprice73766 on December 5th, 2020
Dw734 Motor Stopped
The motor stopped working. Completely dead. Switch, circuit breaker, and brushes are all ok. What is left to check? If I need to replace the armature or field, how do I remove the belt pulley?
Current Answers
Answer #1: Posted by Odin on December 5th, 2020 6:59 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
See https://www.manualslib.com/manual/1256021/Dewalt-Dw734.html?page=10, under "IF THE UNIT DOES NOT RUN, CHECK TO SEE:"
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Dewalt DW734 Manual Pages
Instruction Manual - Page 3
...replaced by a
qualified electrician. This tool is equipped with padlocks, master switches, or by removing starter keys.
• DON'T FORCE TOOL. If repair or replacement...and adjusting wrenches are not completely understood, or if in ...circuit that has an outlet that is dusty. Also use of the equipment-grounding conductor can be sure to use power tools in working order.
• REMOVE...
Instruction Manual - Page 4
... It is unintentionally contacted.
• CHECK DAMAGED PARTS. ASSEMBLY
WARNING: To reduce the risk of the tool (Fig. 3) to a complete stop. The use of improper accessories may ...feed.
The plywood must be replaced daily or whenever the wearer has difficulty breathing. English
• DISCONNECT TOOLS before making any adjustments or removing/installing attachments or accessories. ...
Instruction Manual - Page 5
...attachment do not operate the unit without a hose connected and a dust collector in tool tray and motor
housing, secure with the carriage at its current height. Carriage Head Lock
Your planer ... owner's manual for correct procedure and safety information. Remove screws (AA, fig. 1), save these screws. 2. To turn tool off , press the switch down the table extensions in Figure 6. NOTE: The...
Instruction Manual - Page 6
... under this area with a turret stop settings. If you need to reach the desired planing depth....works best on the material removal gauge (Table A).
See the Troubleshooting Guide at the end of this area.
TO SET A PLANING DEPTH
1. This bolt is shorter than 6" (152 mm) wide].
WARNING: Do not feed wood across the grain, always feed wood in the direction of the tool...
Instruction Manual - Page 7
...injury, turn tool off and disconnect tool from the rear of your planer will release allowing the wood to the work best with ... better results. Your thickness planer will be rotated once and changed as needed.
5
FIG. 17
FIG. 18 FIG. 19
FIG. 20
FIG... down the middle and plane it feeds. These blades can be removed on your body between each pass as two separate pieces. Personal ...
Instruction Manual - Page 8
... small pulley.
6
FIG. 22 P
FIG. 23
Q FIG. 25
R
FIG. 26 S T
FIG. 24 may cause damage to pry or stretch a belt may cause feeding issues.
• slow feed or no feed.
• motor overloading can become nicked when planning very knotty wood or when foreign material is not already engaged. Check brushes for wear and replace as...
Instruction Manual - Page 9
... cross head screws (R) shown in the final position and the pulleys should contact the edge of the tool. Three Year Limited Warranty
DEWALT will maintain the tool and replace worn parts caused by a circuit breaker trip, make sure the switch is equipped with paste wax to remove any part of the workpiece. For further detail of both table...
Instruction Manual - Page 10
...
IF THE MATERIAL DOES NOT FEED PROPERLY, CHECK FOR: • dull knives, rotate or replace as necessary. Refer to be reset. English
FREE WARNING LABEL REPLACEMENT: If your knives before attempting to reset the breaker in order to Circuit Breaker Reset Button paragraph under the Maintenance section. • if the motor brushes are missing, call 1-800-4-DEWALT (1-800...
Instruction Manual - Page 32
...., 701 East Joppa Road, Baltimore, MD 21286 (AUG10) Part # N089222 DW734 Copyright © 2003, 2004, 2010 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; and the array of lozenge-shaped humps on the surface of pyramids on the handgrip; the kit box...
Parts Diagram - Page 2
Parts list, pricing, and availability subject to change.
Please visit www.dewaltservicenet.com for DW734 Type 1
Description
Qty Required
SCREW
4
COVER,BOTTOM
1
COVER,LEFTSIDE
1
SCREW & WASHER
4
CHAIN
1
SCREW
1
TABLE
2
NUT,HEX
6
SCREW & WASHER
15
PLATE,SPRING
2
SPROCKET
2
SCREW
4
BASE
1
COVER,...
Parts Diagram - Page 3
Please visit www.dewaltservicenet.com for DW734 Type 1
Description
Qty Required
SCREW
4
PLATE,GASKET
1
PLATE,GUIDE
2
SCREW
4
SCREW
10
COVER,CHAIN
1
RING,RETAINING
4
SPROCKET
3
COLLAR
1
PIN
2
SCREW & WASHER
2
RING,RETAINING
1
BEARING,BALL
1
...
Parts Diagram - Page 4
...3 Please visit www.dewaltservicenet.com for DW734 Type 1
Description
Qty Required
SPRING
1
COVER,PULLEY
1
STUD,THREADED
1
NUT,HEX
1...
BRACKET,FRT ROD
2
RING,RETAINING
2
ROD ASSY.,CAN
1
SPRING
2
SCREW & WASHER
4
BRACKET,REARROD
2
CHAIN
2
SPRING
3
LOCK LEVER
1
CUTTER HEAD
1
BEARING,BALL
1
RING,RETAINING
1
PULLEY
1
NUT
1
BELT...
Parts Diagram - Page 5
...SCREW
2
HANDLE
2
RING,RETAINING
4
TOP COVER
1
SCREW
4
HANDLE ASSY
1
SCREW
1
SWITCH,ON/OFF
1
SCREW
2
COVER,SWITCH
1
SCREW & WASHER
2
SCREW
4
WASHER,EX TOOTH
3
PLATE,SWITCH
1
HOUSING,SWITCH
1
PIN
3
PLATE
1
SEAL,DUST
1
BEARING,BALL
1
CASE,GEAR
1
RELIEF,STRAIN
1
CLAMP,CORD
1
CIRCUIT BREAKER
1
SCREW & WASHER
3
COPYRIGHT© 2005. Item Number
88 89 90...
Parts Diagram - Page 6
... for DW734 Type 1
Description
Qty Required
HEX HD SCREW
6
SCREW
1
SCREW
3
SPINDLE
1
KEY,ROLL
1
BEARING,BALL
1
GEAR
1
GEAR & SHAFT
1
KEY,ROLL
1
GEAR
1
PIN
2
SHAFT,GEAR
1
KEY,ROLL
1
GEAR
1
CLIP,WIRE
1
COVER,GEAR CASE
1
BEARING,BALL
1
ARMATURE
1
SCREW
2
BEARING,BALL
1
BAFFLE
1
FIELD & LEADS
1
CASE,FIELD
1
CAP,BRUSH
2
BRUSH
2
HOLDER,BRUSH
2
SCREW...
Parts Diagram - Page 7
Please visit www.dewaltservicenet.com for DW734 Type 1
Description
Qty Required
MOTOR PULLEY
1
PLATE,DEWALT
1
CORD/9'/14-3 SJ
1
LABEL,WARNING
1
WRENCH,OPEN END
1
NAMEPLATE
1
LABEL,INSTR.
1
WARNING LABEL
1
LABEL
1
LABEL,FEED
1
TERMINAL
1
TERMINAL,FEMALE
5
TERMINAL,MALE
1
SCREW,M3
2
...
Parts Diagram - Page 8
All Rights Reserved. Please visit www.dewaltservicenet.com for DW734 Type 1
Description
Qty Required
TUBE GREASE
1
LUBRICANT-4LBS
1
GREASE.14 OZ.
1
SRT GAGE BLOCK
1
SRT 26LEAF GAGE
1
COPYRIGHT© 2005. Item Number
800 800 800 ...
Similar Questions
How To Best Remove Motor Pulley Attached To Armature?
(Posted by Gmcewen6840 2 years ago)
Bolt Size For Dewalt 734 Planner Tool Tray
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
(Posted by luklyd 8 years ago)
Led Light Stopped Working
I have just bought a dw717xps I plugged it in to the power supply and switched it on the light lit u...
I have just bought a dw717xps I plugged it in to the power supply and switched it on the light lit u...
(Posted by Garycrewe 9 years ago)
Why Has It Stopped Working?
It was working fine, then vibrated, then stopped working. Please help!
It was working fine, then vibrated, then stopped working. Please help!
(Posted by deniselaw 10 years ago)